Difference between revisions of "BIOS Upgrade"

From ThinkWiki
Jump to: navigation, search
(Booting the image with syslinux: +memdisk at Ubuntu)
m (Installed Firmware: pretty space instead of underline)
 
(164 intermediate revisions by 54 users not shown)
Line 1: Line 1:
__TOC__
+
{| width="100%"
 +
|style="vertical-align:top;padding-right:20px;width:10px;white-space:nowrap;" | __TOC__
 +
|style="vertical-align:top" |
 +
This page is meant to describe ways to update the BIOS on a ThinkPad that only runs Linux for users that don't have ready access to Windows. If you have Windows on your ThinkPad you can just boot into it and follow instructions on the Lenovo website.
  
This page is meant to describe ways to update the BIOS on a ThinkPad that only runs Linux for users that don't have ready access to Windows. If you have Windows on your ThinkPad you can just boot into it and follow instructions on the IBM website.
+
Updating the BIOS in Linux (with few exceptions) '''is not officially supported''' by Lenovo. However there are work arounds.
  
{{NOTE| In one case ([[APM setup on a type 2379 ThinkPad T40]]) it was not possible to upgrade the BIOS from Windows XP; a downgrade to Windows 98 was required to successfully run the BIOS upgrade app. The symptoms in this case were that, once the files had been extracted to the hard disk, and the machine was to reboot into the upgrade app, it would beep and hang just before reboot, requiring a power cycle. Once the power was cycled, it would simply reboot back into XP without performing any BIOS upgrade actions. So even if you have Windows, you may still need to use the info on this page.}}
+
<BR>
 +
{{WARN|By following any of the instructions here you are accepting the '''very real risk''' of turning your ThinkPad into a big expensive paper weight, as a firmware update gone wrong can create unfix-able problems.
  
----
+
'''Proceed at your own risk!'''}}
==Before You Begin==
+
|}
Updating the BIOS in Linux (with few exceptions) '''is not officially supported''' by IBM/Lenovo.  However there are work arounds.
+
 
 +
= [[Custom BIOS]] =
 +
 
 +
Some ThinkPad fans have created Custom BIOSes to remove whitelists, disable annoying errors, do Fn-Ctrl keyswaps, and add more functionality. Check the [[Custom BIOS]] wikipage for more information.
 +
 
 +
* '''X200, X60, T60, Macbook 2,1''' - [http://libreboot.org Libreboot] - Based on Coreboot, this BIOS (approved by the FSF) removes all proprietary blobs to create Free Libre Open Source Laptops, where everything from the motherboard to the computer can use Open Source Software. Richard Stallman famously uses a Libreboot X60.
 +
* Sovem's Whitelist Removed BIOSes - A famous user from BIOS-mods.com, that removes mPCI whitelists from BIOSes upon request.
 +
* '''T61, R61, X61/X61s/X61T, X300''' - [[Middleton's BIOS]] - Enables SATAII, removes whitelist, thermal fixes, Fn-Ctrl swap.
 +
* '''T43/T43p, R52, X41/X41T''' - [[Problem with non-ThinkPad hard disks#Use unofficial modified BIOS|TTav134's BIOS]] - Removes Error 2010 for aftermarket hard drives, and the BIOS whitelist.
 +
 
 +
== [[Middleton's BIOS]] ==
 +
 
 +
A user on NotebookReview named 'Middleton' made these alternative BIOSes to enable SATA2 on certain Thinkpad models (X61/T61/R61/X300). These ThinkPads are limited to SATA1 in their BIOS even though the hardware is SATA2. This is a huge drawback for anyone wanting to use SSDs, because it is so much slower.
 +
 
 +
Also, it is not possible to install some wireless cards, because only certain models are whitelisted by IBM/Lenovo. [[Middleton's BIOS]] removes this limitation as well.
 +
 
 +
'''See the wikipage [[Middleton's BIOS]] for installation instructions, downloads, and more description.'''
 +
 
 +
Note: If your BIOS-Update tool says that no update is needed, then simply downgrade the Bios first: On Lenovo's drivers download page, the old Bios files are listed at the very bottom of the page.
 +
 
 +
= Downloading New Firmware =
 +
{{WARN|Flashing the wrong firmware for your hardware may cause permanent damage to your ThinkPad.  It is up to you to confirm that the firmware you are using is correct.}}
 +
 
 +
A list of links to firmware downloads can be found at [[BIOS Upgrade Downloads]] for most Thinkpad models.  You can also check the Lenovo Support website's [http://support.lenovo.com/en_US/downloads/default.page?#|ThinkPad driver matrix].
 +
 
 +
Lenovo/IBM provides firmware upgrades in a variety of packages:
 +
* Diskette
 +
* Non-diskette
 +
* Linux diskette
 +
* BIOS Utility
 +
* Bootable CD
 +
 
 +
Not every type of package is available for every model.
 +
 
 +
The ''BIOS Utility'' and ''Bootable CD'' packages combine the BIOS and ECP firmwaresFor the other packages, there is one for each firmware.
 +
{| align="right" style="width:20em;"
 +
| {{HELP|Can an image be extracted from a "Linux diskette" .exe file?}}
 +
|}
  
{{WARN|By following any of the instructions here you are accepting the '''very real risk''' of turning your thinkpad into a big expensive paper weight, as a firmware update gone wrong can create unfixable problems.
+
The ''Linux diskette'' is just the ''Diskette'' package that runs on Linux instead of Windows/DOS.  It's unknown if a boot image can be extracted from it.
  
'''Proceed at your own risk!'''
+
You may need to try different packages to find the one from which you can extract a boot image.
  
It is also important to understand that Thinkpads from IBM have two separate firmwares: the BIOS, and the Embedded Controller program.  A given BIOS version will require a certain version of the Embedded Controller program.
+
== Two Firmwares: BIOS and ECP ==
 +
{{WARN|Flashing incompatible firmwares, or flashing them in the wrong order, may cause permanent damage to your ThinkPad.}}
  
The IBM documentation is sometimes unclear about the order in which these two firmwares should be updated.  On most, but not all Thinkpads, '''the correct update order is Embedded Controller program first, and then the BIOS'''.  Make sure to do the two updates immediately one after the other. Newer models from Lenovo update both the Embedded Controller program and the BIOS at the same time, so you don't have to worry about it.}}
+
It is important to understand that Thinkpads from IBM have two separate firmwares: the BIOS, and the Embedded Controller Program (ECP).
 +
 
 +
A given BIOS version will require a certain version of the ECP.  You must read the Lenovo website and/or .txt files to confirm which BIOS is compatible with which ECP, and '''the order in which to update them'''. 
 +
 
 +
=== Update Order ===
 +
The Lenovo/IBM documentation is sometimes unclear about the order in which these two firmwares should be updated.  When in doubt (i.e. IBM didn't provide specific instructions for your model or a particular firmware update), '''update the ECP first, and then the BIOS'''.  Also, make sure to do the two updates '''immediately one after the other'''.
 +
 
 +
The EC firmware is usually much better at backwards compatibility than the BIOS.
 +
 
 +
{{NOTE|Updaters for newer models take care of both BIOS and EC, and use automatically whatever sequence is needed, so you don't have to worry about it.}}
 +
 
 +
== Installed Firmware ==
 +
You can check the current BIOS and ECP versions on your ThinkPad as detailed here: [[BIOS Version]]
  
 
===DMI IDs===
 
===DMI IDs===
 
Please consider updating the [[List of DMI IDs]] before (and after) updating your BIOS.
 
Please consider updating the [[List of DMI IDs]] before (and after) updating your BIOS.
  
==BIOS Upgrade Paths==
+
= Updating Firmware =
 +
 +
Firmware flasher program can run on DOS (Lenovo PC DOS) or Windows but, unfortunately, not Linux. So ''in theory'' there are two basic steps to update the firmware (either the BIOS or the ECP) on a ThinkPad not running Windows:
 +
# Get or create a bootable image with supported OS
 +
# Boot that image and, if not started automatically, ran flasher program
  
For every firmware (either BIOS or Embedded Controller program) update on the IBM web site there used to be two different firmware update programs provided. The Diskette Updater and the Non Diskette Updater. For newer Lenovo Models the Diskette Updater is replaced with a bootable CD-Image and the Non Diskette Updater is renamed BIOS Update Utility, both of which update the BIOS and the Embedded Controller program at the same time. A list of links to firmware downloads can be found at [[BIOS Upgrade Downloads]] for nearly all Thinkpad Models.
+
Recent Thinkpads have firmwares available as ''Bootable CD'' image, e.g., FILENAME.iso. If you have an optical drive there is no need to read this page any further: just download .iso image, burn it and boot to flash bios. If you are not that lucky, read on.
  
===The Diskette Updater===
+
First you need to realize that there are different ways to boot DOS on PC (theoretically it is possible to boot Windows to ran flasher, but why?...): from internal hard drive, CD drive, USB Flash drive or, as the last resort, floppy drive. Easiest way is from internal hard drive, but you'd better avoid touching it until you don't want to loose files there. [[Booting from a Floppy]] is not recommended, so there are two best options to boot: CD drive or USB Flash drive.
  
{{WARN|If the floppy fails while flashing, your ThinkPad will need a repair shop}}
+
Sparse instructions below provide you guidance how to do different parts of this pazzle but it's your duty to understand what to do and how to do that.
  
The Diskette updater appears to be a 16 bit DOS program which asks you to accept a license agreement.  It will run in Windows, DOS, OS/2, or [http://dosemu.sf.net Dosemu] perfectly, but requires a real floppy disk attached via a real floppy controller.  A USB Floppy Drive will not work.
+
== Using UEFI ==
  
The flash environment can be a really dumb piece of work and it will be reading the data from the floppy as it goes, i.e. it is dangerous as all heck should the floppy reads fail.  Use a clean (in the physical sense) floppy and floppy drive.  Have two or more flash disks ready, all of them binary copies of each other, and all of them tested to be perfectly readable.  And the only thing you can tell DOS without risking your ThinkPad, is to "Retry" if it asks.
+
Especially usable when CDROM is not available, tested on X140e, but should work in most recent firmwares as these supports UEFI, much simpler than older methods outlined in this and other pages.
  
Important floppy-drive knowledge for those who are not used to them:
+
You should have a USB mass storage device you can erase.
* One floppy is never enough.  Good quality ones are very dependable for short-time data storage when new, but chances are you'll be using either old or extra-shitty diskettes (good ones have not been manufactured for a long while now), so you cannot trust them at all
+
* When a floppy fails to read because you failed at the "use clean floppies" part, it may get dirt stuck to the drive head and will not work well until cleaned
+
* You can clean a floppy disk, but it requires much care as you must do it without using any fluids, and you only want to remove the dirt on top of the metal-oxide layer, without damaging said layer (i.e. you can't rub it, and you can't cause any scratches)
+
* Dirty driver heads sometime damage floppies.  Wet driver heads always damage floppies.  Clean the drive heads first, and make sure to wait until they dry before inserting a floppy in the drive
+
* You may need to clean the floppy drive head before it will work again if it gets dirty.  You'll need the usual "floppy disk cleaner diskette with isopropil alcohol" kit to fix it (if you know the other way to clean the heads, you don't need to be reading this!), always telling DOS to "retry" (hit anything else, and your ThinkPad is likely toast)
+
* If you forget to let the head dry after a cleaning, it will destroy the next floppy it touches and get very dirty.
+
  
===The Bootable CD Image===
+
{{WARN|this will erase the USB mass storage device content.}}
  
Newer models from Lenovo can be updated using the Bootable CD Image. This should be the easiest way for non-Windows users and also maybe a more secure way for Windows users, as well. As the image is provided as a plain ISO-file without any Windows enclosure, you can simply burn it to a CD-R/RW with any modern operating system, as long as you have a CD/DVD-RW Drive and are then able to boot from it.
+
1. Download BIOS update ISO image, we assume it is xxx.iso.
  
===Extracting a Bootable CD-ROM Image from the Non Diskette Updater===
+
2. Extract bootable image using [https://userpages.uni-koblenz.de/~krienke/ftp/noarch/geteltorito/ geteltorito] tool:
{{WARN|Though this process was successfully tested on one version of .exe files found on IBMs website this doesn't mean it will work for all of them. Proceed at your own risk.  Consult the list at the bottom of this page to see other users' experience with your model Thinkpad.}}
+
  
This installer appears to be a 32bit windows .exe which is designed for updating the BIOS directly from a running Windows OS.  It turns out that this .exe is really a wrapper license program around Windows .cab files (see [[How_to_change_the_BIOS_bootsplash_screen|BIOS-Bootsplash]]). If you install the Linux program [http://freshmeat.net/projects/cabextract/ '''cabextract'''] you can expand these .cab files directly. Run the following:
+
{{cmduser|./geteltorito.pl -o xxx.img xxx.iso}}
  
:{{cmduser|cabextract FILENAME.exe}}
+
3. Insert USB device, checkout its device, we assume /dev/sdX.
  
This will extract 8 files in the current directory. One of them will be FILENAME.img.  In this discussion, "FILENAME" represents the name of the Non Diskette file that you downloaded, such as "1NHJ04US".
+
4. Dump content of image to USB device.
  
The non Diskette download was not extractable for at least the version 3.23 (T41p), but the diskette version worked perfectly - cabextract delivered a .img file to continue here...
+
{{WARN|Double check the device name so you do not overwrite any other filesystem.}}
  
You can test that this is really a floppy image by running:
+
{{cmdroot|<nowiki>dd if=xxx.img of=/dev/sdX</nowiki>}}
  
:{{cmdroot|mkdir mntfloppy}}
+
5. Reboot, enter BIOS setup, enable UEFI only (or 1st priority) at startup options, save and reboot.
:{{cmdroot|mount -o loop FILENAME.img mntfloppy}}
+
:{{cmdroot|ls -la mntfloppy}}
+
  
If the results of {{cmdroot|ls -la mntfloppy}} look like a dos floppy, and no read errors were displayed, you have a pretty good chance that the floppy image is usable.
+
6. Interrupt boot, press F12 and select USB mass storage device as boot source.
  
Unmount the image after you are done:
+
7. The BIOS update utility should run and you should succeed in flashing BIOS.
  
:{{cmdroot|umount mntfloppy}}
+
== Create a bootable image ==
  
Now, you can proceed to [[BIOS_Upgrade:Creating a Bootable CD from a Floppy Image]], below.
+
In case Lenovo does not provide your laptop with ''Bootable CD'' it is possible to create one from *discket packages.
  
===Booting the image with syslinux===
+
=== Extracting an update image ===
 +
{{WARN|Though this process has been successfully tested on many versions of .exe files found on IBMs website, that doesn't mean it will work for all of them.  '''Proceed at your own risk'''.  Consult the testing tables farther down of this page to see other users' experience with your model Thinkpad.}}
 +
{{NOTE|Lenovo has changed the packaging format. Old bios can be extracted with [http://freshmeat.net/projects/cabextract/ '''cabextract'''], new ones with [http://innoextract.constexpr.org/ '''innoextract'''].}}
 +
Older .exe installers from Lenovo mostly appear to be just a wrapper license program around Windows .cab files (see [[How_to_change_the_BIOS_bootsplash_screen|BIOS-Bootsplash]]). If you install the Linux program [http://freshmeat.net/projects/cabextract/ '''cabextract'''] you can expand these .cab files directly.  For example, if you downloaded {{path|1iuj13us.exe}} from Lenovo:
  
Once the image is extracted from the Non Diskette Updater, it can be booted directly through GRUB without the need of burning a CD. This method has been tested on T42 with a broken DVD-ROM, but it should be applicable to any ThinkPad.
+
:{{cmduser|cabextract 1iuj13us.exe}}
  
'''1.''' Download the '''Non Diskette Updater'''.
+
Extracting cabinet: 1iuj13us.exe
 +
  extracting 1IUJ13US.IMG
 +
  extracting BIOSUPTP.EXE
 +
  extracting DOBOOT.EXE
 +
  extracting DOSBOOT.COM
 +
  extracting DOSBOOT.SYS
 +
  extracting DOSBOOT.VXD
 +
  extracting DOSBOOT2.COM
 +
  extracting ECTLUPTP.EXE
 +
  extracting EFLASHAS.SYS
 +
  extracting HDFWUPTP.EXE
 +
  extracting IBMTPI.XML
 +
All done, no errors.
  
'''2.''' Extract the images using '''cabextract''' (see previous sections for details). Let's say that the image file is called {{path|1RUJ37US.IMG}} (replace with the actual filename).
+
The file we want is '''FILENAME.IMG''', with "FILENAME" being the .exe. you downloaded.  E.g., {{path|1IUJ13US.IMG}}.
  
'''3.''' Make sure that <tt>syslinux</tt> package is installed in your system. Locate the <tt>memdisk</tt> file from the syslinux package. In case of openSUSE 11.1, it is placed in {{path|/usr/share/syslinux/memdisk}}. On Ubuntu 9.04, it can be found at {{path|/usr/lib/syslinux/memdisk}}.
+
If this does not work for the Non-diskette .exe, try it on the Diskette .exe.  It's reported, for example, that the Non-diskette .exe for BIOS version 3.23 for the T41p was not extractable, but the Diskette .exe worked perfectly, with {{cmduser|cabextract}} delivering a .IMG file.
  
{{HINT|If you use rpm, try calling <tt>$ rpm -q syslinux --list</tt>}}
+
==== If cabeextract/innoextract fails ====
  
'''4.''' Copy both the '''image and memdisk''' files into {{path|/boot}} directory. You must be root to do this.
+
Diskette .exe for some older models can't be extracted using cabextract. For example for the latest BIOS of 390E one gets
 +
spsdilc9.exe: no valid cabinets found
 +
There is a simple way to solve this, by stripping the header off from the Non-diskette version. To do this, first you need to find the index for the first occurance of '''MSCF''' in the downloaded executable. This can be done with the following
 +
strings -a -t d NO-DISKETT.EXE | awk 'offset=index($2,"MSCF"), (offset != 0) {print $1+offset-1}' | head --lines 1
 +
4196
 +
The command adds the byte offset of the matching line plus the index for the start of the '''MSCF''' on that line, thus the byte offset of '''MSCF''', this number is usually '''4196''' Now we need to cut these header bytes off, this is done by a standard dd cut, the following cuts away the first 4196 bytes.
 +
dd if=NO-DISKETTE.EXE of=out.cab iflag=skip_bytes skip=4196
 +
The newly created '''out.cab''' should now work with '''cabextract'''
 +
cabextract out.cab
  
{{cmdroot|cp ./1RUJ37US.IMG /usr/share/syslinux/memdisk /boot/}}
+
A second alternative is to use Windows XP (works in VirtualBox too) together with [http://sourceforge.net/projects/vfd/ Virtual Floppy Drive]. Rund vfdwin.exe, go to the Driver tab and hit Install and Start. Then go to the Drive0 tab, click on Change and select A:. Finally, click on Open/Create, and click Create. This should give you a virtual floppy drive the .exe file will extract files to.
  
'''5.''' Open {{path|/boot/grub/menu.lst}} in your favourite editor.
+
A third solution is to use QEMU with a DOS diskette image to run the disk extractor.
  
'''6.''' Copy the active section and edit <tt>title</tt>, <tt>kernel</tt>, <tt>initrd</tt> according to this example:
+
==== Testing the Image ====
  
<pre>title IBM BIOS update
+
You can test that FILENAME.IMG is really a floppy image by running:
    root (hd0,0)
+
    kernel /boot/memdisk
+
    initrd /boot/1RUJ37US.IMG
+
</pre>
+
  
{{NOTE|The <tt>root</tt> section must remain unchanged. This tells GRUB, on which partition the image is located.}}
+
{{cmdroot|mkdir /tmp/mntfloppy}}
{{WARN|Do not modify the original section in <tt>/boot/grub/menu.lst</tt>. You might not be able to boot back to the operating system}}
+
  
== Updating Thinkpad X Series ==
+
{{cmdroot|mount -o loop FILENAME.IMG /tmp/mntfloppy}}
  
The special update instructions for X series Thinkpads are quite long. You can find them at the page [[BIOS_Upgrade/X_Series]].
+
If a '''ls''' command on the image returns what looks like a DOS floppy, and no read errors were displayed, you have a pretty good chance that the image is usable. For example:
  
==Updating via CD/DVD Drive==
+
{{cmdroot|ls /tmp/mntfloppy}}
 +
$0195000.FL1  069580.PAT  06d2.HSH    IBMDOS.COM    TPCHKS.EXE
 +
0691.HSH      06D0.PAT    06d6.HSH    LOGO.BAT      UPDTFLSH.EXE
 +
0691.PAT      06D1.PAT    06d8.HSH    LOGO.SCR      UPDTMN.EXE
 +
0694.HSH      06D2.PAT    CHKBMP.EXE  PHLASH16.EXE  USERINT.EXE
 +
0694.PAT      06D6.PAT    COMMAND.COM  PREPARE.EXE  UTILINFO.EXE
 +
0695.HSH      06D8.PAT    CONFIG.SYS  PROD.dat      lcreflsh.bat
 +
0695.PAT      06d0.HSH    FLASH2.EXE  QKFLASH.EXE
 +
069580.HSH    06d1.HSH    IBMBIO.COM  README.TXT
  
The whole thing gets more complicated if you neither have Windows nor a floppy drive installed. This is what this page is intended to describe.
+
Unmount the image after you are done testing:
  
Another possibility which works even without a CD-drive or network is to boot the disk image via the grub initrd mechanism.
+
{{cmdroot|umount /tmp/mntfloppy}}
  
Be aware that IBM officially does '''not''' support this! The official statement to my support request was:
+
== Booting from update image ==
 +
Now that you have a bootable image for the correct update for you hardware, you need to do is boot from that image to install the update.
  
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
There are different ways to do that:
<pre><nowiki>
+
* [[#Booting from a CD|Boot from a CD]]
I'm afraid we only support the options listed on our web page and no you
+
* [[#Booting_using_GRUB|Boot image using bootloader (e.g. GRUB)]]
can't burn a CD/DVD, however you can try to use an external USB FDD
+
* [[#Booting_from_a_USB_Flash_drive|Boot from a USB Flash drive]]
(floppy) drive. The experts recommend a IBM USB FDD, however they have also
+
* [[#Booting_from_a_floppy|Boot from a floppy]]
tested it with a Sony USB FDD drive.
+
  
In order to make sure the drive is recognised you can boot up the FDD with
+
=== Booting from a CD ===
a bootable dos diskette for w98
+
{| align="right" style="width:40em;"
</nowiki></pre>
+
|{{HINT|If there is a ''Bootable CD'' image available, e.g., FILENAME.iso, just download that, instead of mucking around with image files.}}
</blockquote>
+
|}
 +
If you are going to update the firmware by booting from a CD, you need to turn FILENAME.IMG that you extracted above into an .iso file.
  
But it seems to be possible as Mathias Dalheimer describes this [http://mailman.linux-thinkpad.org/pipermail/linux-thinkpad/1998-January/009743.html here].
+
The [http://en.wikipedia.org/wiki/El_Torito_%28CD-ROM_standard%29 El Torito Bootable CD Specification] is a wonderful thing.  Thanks to it, a bootable CD can be made with a bootable floppy image in such as way that the CD believes that it is a 2.88 MB floppy drive.  This allows you to replace a boot floppy by a boot CD in nearly all situations.
  
Another indication that it should work is that IBM uses PHLASH16.EXE (at least on T4x/p systems) to flash the BIOS into the chip. The same tool is used by [http://www.samsungpc.com/gb/support/p35/bios/bios-instructions.html other vendors] to flash the BIOS from bootable CD-ROMs.
+
It is very easy to create such a bootable CD ISO image in Linux using the '''mkisofs''' tool{{footnote|1}}. Run a command as follows:
{{WARN|Do '''not''' use the [http://syslinux.zytor.com/ SYSLINUX] image-loader [http://syslinux.zytor.com/memdisk.php MEMDISK] to boot the images! Some flash tools crash in that situation!}}
+
  
Some interesting but very technical information about the used flash tool can be found [http://www.paul.sladen.org/thinkpad-r31/wifi-card-pci-ids.html here].
+
{{cmdroot|genisoimage -b 1WUJ25US.IMG -c boot.catalog -o bootcd.iso 1WUJ25US.IMG}} #or older mkisofs
  
===Creating a Floppy Image===
+
Where *.IMG is the name of the image file extracted above. This creates a CD with one file on it and marks that file as the boot image.
If you have created a boot floppy on another machine, you need to create an image file of that floppy. This can be easily done in linux by running a command line:
+
  
:{{cmdroot|1=dd bs=2x80x18b if=/dev/fd0 of=/tmp/floppy.img}}
+
You can now burn the {{path|bootcd.iso}} to a CD in your favorite CD-burning program.
 +
{{WARN|By following any of the instructions here you are accepting the '''very real risk''' of turning your ThinkPad into a big expensive paper weight, as a firmware update gone wrong can create unfix-able problems. '''Proceed at your own risk!'''}}
  
You can also create a floppy image by using Ken Kato's [http://chitchat.at.infoseek.co.jp/vmware/vfd.html VMware's back]. It is a free Windoze tool that creates a virtual floppy drive and allows you to produce an image file ready to be ISO'ed. Note: you might have to 'manually' (through application's interface) assign the virtual drive a volume letter in order to be seen by IBM's application (as, by default, it seems not to do it).
+
Boot from the CD to update your firmware.  Remember to have [[BIOS_Upgrade#Two_Firmwares:_BIOS_and_ECP|both BIOS and ECP firmware boot-CDs]] ready, as needed, and use them in the [[BIOS_Upgrade#Update_Order|proper order]].
  
You should verify this {{path|floppy.img}} as explained above.
+
{| align="center"
 +
| {{HELP|Please, report your success/failure with flashing BIOS from the manually cooked CD (from .IMG file) here: [[BIOS_Upgrade_success_failure#Booting_from_CD]]}}
 +
|}
  
===Creating a Bootable CD from a Floppy Image===
+
=== Booting using GRUB ===
Once you have your floppy image, either from imaging a real floppy, or from extracting them via the cabextract method above, you need to make a boot CD out of it.
+
{|
 +
| style="width:75%" | {{WARN|Many have warned '''not''' to use the SYSLINUX image-loader '''memdisk''' to boot firmware update images.}}
 +
| style="font-size:80%" | {{HELP|Who are these "many"?  Link to a discussion?}}
 +
|}
 +
Once the bootable image, FILENAME.IMG, is extracted from the .exe, it can be booted directly through GRUB without the need of burning a CD, using the [http://syslinux.zytor.com/ SYSLINUX] image-loader '''[http://syslinux.zytor.com/memdisk.php memdisk]'''.
  
The eltorito bootable CD standard is a wonderful thing. What this means is that a bootable CD can be made with a bootable floppy in such as way that the CD believes that it is a 2.88 MB floppy drive.  This allows you to replace a boot floppy by a boot CD in nearly all situations.
+
Locate the '''memdisk''' file from the syslinux package. You can search for it with '''find''':
  
It is very easy to create such a bootable CD ISO image in Linux using the mkisofs tool.  To do this run a command as follows:
+
{{cmdroot|find /usr -name memdisk}} #or just use "dlocate memdisk" or "locate memdisk" if these programs are installed
  
:{{cmdroot|mkisofs -b bootfloppy.img -o bootcd.iso bootfloppy.img}}
+
If {{path|/usr/.../memdisk}} is not present, syslinux is not installed.  You will need to install it to boot a .IMG from GRUB.
  
where bootfloppy.img is the name of the .img floppy image file, for example 1NUJ10US.IMG.
+
Copy both the '''FILENAME.IMG''' and '''memdisk''' files into {{path|/boot}} directory. For example:
  
Note: This creates a CD with one file on it and marks that file as the boot image.  For more info on this read {{cmduser|man mkisofs}}.
+
{{cmdroot|cp ./FILENAME.IMG /usr/share/syslinux/memdisk /boot/}}
  
You can now burn the {{path|bootcd.iso}} in your favorite CD burning program.
+
Open {{path|/boot/grub/menu.lst}} in your favourite editor. '''Copy''' the active section into a '''new section''', and edit the new section:
 
+
To get an overview which models have been tested with this version, here is a list:
+
 
+
===Does work:===
+
 
{| border="1" cellspacing="0" cellpadding="2"
 
{| border="1" cellspacing="0" cellpadding="2"
| '''Model''' || '''Tested by'''
+
! Parameter
 +
! Instructions
 +
! Example
 
|-
 
|-
| style="vertical-align:top;" | {{600E}} (2645-4AU) ||
+
| ''title'' || Pick a name for the new section. This will show up in the GRUB boot menu. || <tt>title IBM ECP Update</tt>
*George Tellalov <gtellalov_dontspamme@bigfoot.com>. BIOS 1.16 from spsdin36.exe worked perfectly with the method bootable cd from floppy image. I highly recommend this upgrade because it made my ibm-acpi module load (it wouldn't load before) and fixed some suspend to ram problems. Here's the [http://george.tellalov.info/bios_upgrade_600e_spsdin36.iso cd image] I used. Use at your own risk. You can send me a chocolate if it works for you ;)
+
 
|-
 
|-
| style="vertical-align:top;" |  {{600E}} (2645-5bU) ||
+
| ''root''  || Do not change. This is the partition containing the {{path|/boot}} directory      || <tt>root (hd0,0)</tt>
*Mike Vincent<matchstc-putobvioushere.com>. Bios 1.16 from spsdin36.exe and then to the boot cd worked great for me. Thought I had bricked it three separate times using a "real" floppy! Each from different diskettes .The updater would start, give me the "going to take30 seconds" speech...and then access the HD for 10 minutes. Each time it would reboot fine. Did the cd as described above...worked great first time. Perhaps 10 year old seldom used floppy disc drives have some challenges?
+
 
|-
 
|-
| style="vertical-align:top;" | {{600X}} (2645) ||
+
| ''kernel'' || '''/boot/memdisk''' will allow you to boot an image file.                  || <tt>kernel /boot/memdisk</tt>
*Jonathan Byrne <jonathan@RemoveThisToMailMe.yamame.org>. BIOS 1.11 from spsuit55.exe worked perfectly using cabextract/CD method.
+
 
|-
 
|-
| style="vertical-align:top;" |  {{600X}} (2645) ||
+
| ''initrd'' || This is the name of the firmware-updater image file, e.g., 1IUJ13US.IMG    || <tt>initrd /boot/1IUJ13US.IMG</tt>
*Andy Barnes <andy@RemoveThisToMailMe.itchypaws.co.uk>. As per Jonathan above, extracted BIOS 1.11 from spsuit55.exe using cabextract, created a CD boot image and burnt to CD.  Worked flawlessly - thanks to everyone who contributed to this article!
+
|-
+
| style="vertical-align:top;" |  {{A20p}} (2629-6VU) ||
+
*Chris Pickett http://www.sable.mcgill.ca/~cpicke/. BIOS 1.11 flashed fine with cabextract/CD method.
+
|-
+
| style="vertical-align:top;" |  {{A21e}} (2628-JXU) ||
+
*Amit Gurdasani <gurdasani at yahoo dot com>. BIOS 1.13 flashed fine with cabextract/CD method. Alarmingly, after the BIOS update, the laptop beeped but did not shut down as was indicated onscreen -- that was frozen on the "do not shut down the laptop" screen. On power down and up again, the BIOS setup showed the newer BIOS image running, and Linux booted up fine. Linux ACPI didn't complain about the BIOS being too old either.
+
|-
+
| style="vertical-align:top;" |  {{A31p}} (2653) ||
+
*Matthias Meinke largeeddy@gmx.at, BIOS 1.09 1NET15WW flashed fine with cabextract/CD method.
+
|-
+
| style="vertical-align:top;" |  {{A31}} (2652) ||
+
*[[User:Wnoise|Aaron Denney]], BIOS 1.13 flashed fine with cabextract/CD method.  The cabextract/CD method also worked for BIOS 1.10.
+
|-
+
| style="vertical-align:top;" |  {{R30}}  ||
+
*Jarrod, 30 August 2007, Thinkpad R30 Type 2656-E0M. BIOS updated to 1.40 (1CETF0WW) using floppy disk/mkisofs/cdrecord. Worked fine, no problems.
+
|-
+
| style="vertical-align:top;" |  {{R31}} ||
+
*[http://mailman.linux-thinkpad.org/pipermail/linux-thinkpad/1998-January/009743.html Mathias Dalheimer]
+
*Sebastian Sauer (with cabextract/CD method)
+
|-
+
| style="vertical-align:top;" | {{R40}} ||
+
*Matthew Lambie, http://lambie.org
+
|-
+
| style="vertical-align:top;" | {{R50}} (1836-3SU) ||
+
*jlbartos <jlbartos at hotmail dot com>
+
|-
+
| style="vertical-align:top;" | {{R50e}} (1834-PTG) ||
+
*item <item at freemail dot hu> : successfully finished with cabextract/CD method for "1wuj25us.exe" (BIOS version 1WET90WW (2.10), Release Date: 2006/12/22)
+
*Christos Nouskas <nouskas at gmail dot com>: upgraded to BIOS version 1WET90WW (2.10) and EC version 1VHT28WW (1.04) using GRUB (BIOS first / EC second)
+
|-
+
| style="vertical-align:top;" | {{R51}} (1829) ||
+
*Robert Uhl <rob dot uhl at gmx dot de>, Jellby <jellby at yahoo dot com>
+
|-
+
| style="vertical-align:top;" | {{R51}} (1830-RM7) ||
+
*Will Parker <stardotstar at sourcepoint dot com dot au> successfully flashed 3.20 using existing 3.04 ECP and retained custom boot splash.
+
|-
+
| style="vertical-align:top;" | {{R51}} (2887) ||
+
*Ingo van Lil <inguin at gmx dot de>
+
|-
+
| style="vertical-align:top;" | {{R52}} (1858) ||
+
*Stuart McCord <stuart dot mccord at gmail dot com>  flashed both BIOS and ECP using cabextract, BIOS flashed first as on IBM website
+
|-
+
| style="vertical-align:top;" |  {{T20}} ||
+
*Franz Hassels <fhassel at suse dot com>
+
|-
+
| style="vertical-align:top;" |  {{T22}} ||
+
*Daniel Maier <nusse teamidiot de>
+
*Mathias Behrle (with cabextract/CD method, Version 1.07 => 1.12) --[[User:Mathiasb|Mathiasb]] 11:58, 14 December 2006 (CET)
+
*Bob Skaroff (cabextract/CD), 1.06 => 1.12
+
*Leo Butler (cabextract/CD), 1.11 => 1.12
+
|-
+
| style="vertical-align:top;" |  {{T23}} ||
+
*Bart Snapp <snapp at uiuc dot edu> Note: I followed IBM's instructions to flash the BIOS *first* and the Embedded Controller *second*.
+
*Moy Easwaran: BIOS 1.18 / EC 1.06a via cabextract and CD-boot.  The BIOS-update exe generated errors in Windows 2000.
+
*Joe Renes: BIOS 1.18 / EC 1.06a on 2006-03-20 via cabextract and CD-boot. Piece of cake.
+
*Raphael Errani: BIOS 1.20 / EC 1.06a on 2006-11-06 via cabextract and CD-boot (using mkisofs). Worked without errors. 1st Bios, 2nd EC
+
*Myron Getman: BIOS 1.20 / EC 1.06a on 9/10/08 via cabextract --> k3b --> CD-boot.  Worked like a charm.  First BIOS update with Linux!
+
*Leo Butler: BIOS 1.13 / EC 1.04 to 1.20/1.06a via cabextract and syslinux/memdisk boot through grub. Worked like a charm and no wasted CD.
+
|-
+
| style="vertical-align:top;" |  {{T30}} ||
+
*Martin Gühring <guehring at gmail.com> BIOS 2.10 via cabextract the Non-Diskette BIOS -> mkisofs '''in the directory the exe was extracted''' to generate the iso -> burn the iso -> boot the CD
+
|-
+
| style="vertical-align:top;" | {{T40}} ||
+
*Sean Dague, http://dague.net
+
*Justin Mason, http://jmason.org
+
*Ivanhoe (Bios 3.19)
+
*Alessandro Raulino (roger_2) EC 3.04 & BIOS 3.23 flashed with cabextract/CD method
+
*Nick Jenkins, using BIOS 3.23 with the [[#The_Non_Diskette_Updater|Non-diskette updater + cabextract method]], then [[#Creating_a_Bootable_CD_from_a_Floppy_Image|created a bootable CD from the cabextracted .IMG file]], then boot that ISO, and it worked great!
+
|-
+
| style="vertical-align:top;" |  {{T40p}} ||
+
*Lukas Krähenbühl, ismo at pop dot agri dot ch
+
*Thomas Achtemichuk, tom at tomchuk dot com. BIOS 3.15 flashed fine with cabextract/CD method
+
|-
+
| style="vertical-align:top;" | {{T41}} ||
+
*Lev Givon (Bios 3.15 / EC 3.04) <lev at columbia dot edu>
+
*Ernesto Hernández-Novich (Bios 3.19 / CP 3.04) < emhn at usb dot ve >
+
*[http://maebmij.org James Ballantine] (Bios 3.21 / CP 3.04) using nondisk/cabextract/CDRW
+
|-
+
| style="vertical-align:top;" |  {{T41p}} ||
+
*Nils Newman, work great. (Version: Bios 3.14 / Embedded Controller 3.04)
+
|-
+
| style="vertical-align:top;" |  {{T42}} ||
+
*Dan (BIOS 3.20 / EC 3.04, cabextract/CD method) <tronic171 at evilphb.org>
+
*Hirosh Dabui <hirosh@dabui.de>
+
*magarzo <mdr.magarzo at gmail.com> (BIOS v.3.23 / Embedded Controller v.3.04 / both with cabextract to non-diskette v. plus Bootable CD {T42 Type: 2373-JXG}
+
|-
+
| style="vertical-align:top;" |  {{T42p}} ||
+
*Robert Schiele <rschiele@uni-mannheim.de>, Joern Heissler <joern@heissler.de>, Hirosh Dabui <hirosh@dabui.de>
+
|-
+
| style="vertical-align:top;" |  {{T43}}  ||
+
*Conrad Rentsch <Conrad dot Rentsch at t-online dot de> (Version: Bios 1.29 / Embedded Controller 1.06)
+
*Tom Heady <tom-thinkwiki.org@punch.net>
+
*Florian Boucault <florian at boucault dot ath dot cx> (Model : 1871-W34 & Version: Bios 1.23 / Embedded Controller 1.03)
+
*Till Heikamp <t dot heikamp at geniusbytes dot com> (Model 2886, Bios 1.22 to 1.29, Embedded Controller 1.03 to 1.06)
+
|-
+
| style="vertical-align:top;" |  {{T60}}  ||
+
*Roman Komkov <roman  at komkov dot org dot ru> (Model 1951, Bios 1.07 to 2.13) Successfully upgraded from CD Image
+
|-
+
| style="vertical-align:top;" |  {{T61}}  ||
+
*Kai Weber <kai.weber  at glorybox dot org> (Bios 1.06 to 1.26) Successfully upgraded from CD Image
+
|-
+
| style="vertical-align:top;" |  {{X20}}  ||
+
*Neil Caunt <retardis at gmail dot com>
+
|-
+
| style="vertical-align:top;" |  {{X21}}  ||
+
*Patrick Leickner <ranma at web dot de>, (BIOS 2.21->2.25 / EC 1.31->1.36) via non-disk/cabextract/mkisofs/cdrecord
+
|-
+
| style="vertical-align:top;" |  {{X22}}  ||
+
*David Emery <dave at skiddlydee dot com>,  (EC 1.30, BIOS 1.32 using non-disk/cabextract/CD method)
+
|-
+
| style="vertical-align:top;" |  {{X23}}  ||
+
*Nils Faerber <nils dot faerber at kernelconcepts dot de> (Embedded Controller 1.30, BIOS 1.32 with cabextract/CD method)
+
|-
+
| style="vertical-align:top;" |  {{X30}}  ||
+
*Hella Breitkopf, [http://www.unixwitch.de/ www]  (Embedded Controller 1.04, BIOS 1.07 with cabextract/CD method)
+
*William Roe <willroe at gmail dot com> (Embedded Controller 1.06, BIOS 1.09 - cabextract/mkisofs/wodim)
+
|-
+
| style="vertical-align:top;" |  {{X31}}  ||
+
*Grzegorz KuÅ›nierz <koniu at sheket dot org>  (Embedded Controller 1.08, BIOS 3.01 with cabextract/CD method)
+
|-
+
| style="vertical-align:top;" |  {{X40}}  ||
+
*Robbie Stone <robbie@serendipity.cx>
+
|-
+
| style="vertical-align:top;" |  {{Z60m}}  ||
+
*[[User:Morle|Morle]] 01:09, 17 Nov 2007 (CEST),  (Embedded Controller 1.18 and Bios 1.24 with cabextract/CD method)
+
 
|}
 
|}
  
===Does not work:===
+
Do '''not''' modify the original section in {{path|/boot/grub/menu.lst}}, or you might not be able to boot back to the operating system.
{|
+
| '''Model''' || '''Tested by'''
+
|}
+
  
Please note that testing this is '''at your own risk'''!!!
+
If you have [[#Two_Firmwares:_BIOS_and_ECP|two firmware updates to do]], you will need a section for each firmware's FILENAME.IMG in {{path|/boot/grub/menu.lst}}.
  
 +
{{NOTE|If both BIOS and ECP are to be updated, be sure to update them in the [[#Proper_Order|proper order]].}}
  
 +
{{WARN|By following any of the instructions here you are accepting the '''very real risk''' of turning your ThinkPad into a big expensive paper weight, as a firmware update gone wrong can create unfix-able problems.  '''Proceed at your own risk!'''}}
  
==Updating via Grub and a Floppy Image==
+
Reboot your computer, entering the GRUB menu and selecting ''IBM BIOS Update'', or whatever you named the new section in {{path|/boot/grub/menu.lst}}.
  
{{WARN|Many have warned '''not''' to use the [http://syslinux.zytor.com/ SYSLINUX] image-loader [http://syslinux.zytor.com/memdisk.php MEMDISK] to boot the images! Some flash tools may crash in that situation! Proceed at your own risk!}}
+
==== Booting image with GRUB2 ====
 +
===== GRUB2: booting floppy Image =====
 +
With grub2, one would ''append'' the following to ''/boot/grub/grub.cfg'' :
 +
menuentry "My BIOS Upgrade" {
 +
set root=(hd0,0) #should match the others in your grub.cfg
 +
linux16 /boot/memdisk
 +
initrd16 /boot/1WUJ25US.IMG #or whatever yours is
 +
  }
  
Floppy images may be booted from Grub via a utility called [http://syslinux.zytor.com/memdisk.php MEMDISK], which may be compiled from the [http://www.kernel.org/pub/linux/utils/boot/syslinux/ '''SYSLINUX source'''].  Copy the compiled memdisk image and the floppy image to your boot directory and configure grub as follows:
+
{| align="center"
 +
| {{HELP|Please, report your success/failure with flashing BIOS from the manually cooked CD (from .IMG file) here: [[BIOS_Upgrade_success_failure#GRUB2:_Booting_floppy_Image]]}}
 +
|}
  
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
===== GRUB2: booting CD Image =====
<pre><nowiki>
+
You must first download the bootable iso file from the Lenovo Website.
title    Bios Flash
+
kernel    /boot/memdisk
+
initrd    /boot/FILENAME.img
+
</nowiki></pre></blockquote>
+
  
Again, proceed at your own risk.  This was tested on an R51 type 2888.
+
===== On Debian and Ubuntu =====
 +
Then, on Debian and Ubuntu, you can install the grub-imageboot package, then you just have to copy the iso file in /boot/images and run update-grub:
 +
<pre>
 +
sudo apt-get install grub-imageboot
 +
sudo mkdir -p /boot/images
 +
sudo cp /home/youruser/Downloads/6uuj12uc.iso /boot/images
 +
sudo update-grub
 +
</pre>
  
This also worked for me on a T41p type 2373. -- [[User:MrStaticVoid|James Lee]] 20:55, 8 May 2006 (CEST)
+
===== Manual method =====
 +
Otherwise, copy the file 'memdisk' from the syslinux package to /boot. Also create a symlink, so you do not have to change the grub configuration for each bios upgrade:
 +
<pre>
 +
sudo su -
 +
cd /boot
 +
cp /home/youruser/Downloads/6uuj12uc.iso .
 +
cp /usr/share/syslinux/memdisk .
 +
ln -s 6uuj12uc.iso biosupgrade.iso
 +
</pre>
 +
Now create the boot entry:
 +
<pre>
 +
cat >> /etc/grub.d/40_custom <<EOF
 +
menuentry "Lenovo BIOS Upgrade" {
 +
    set root=(hd0,1) # <-- check for correct numbering
 +
    linux16 /boot/memdisk iso
 +
    initrd16 /boot/biosupgrade.iso
 +
}
 +
EOF
 +
update-grub
 +
</pre>
 +
Reboot an Select "Lenovo BIOS Upgrade".
  
And it worked for me on a X31 type 2673-CBU. -- [[User:JanTopinski|Jan Topinski]], 18 September 2006
+
For the next Bios Upgrade you'll just need to copy the new iso file to /boot and adjust the symlink.
  
And it worked for me too on a X31 type 2672-CXU, very useful. -- [[User:TheAnarcat|TheAnarcat]] 16:21, 7 March 2007 (CET)
+
{| align="center"
 +
| {{HELP|Please, report your success/failure with flashing BIOS from the manually cooked CD (from .IMG file) here: [[BIOS_Upgrade_success_failure#GRUB2:_Booting_CD_Image]]}}
 +
|}
  
Same here (worked) on a X31 type 2673-58G --[[User:FaUl|FaUl]] 15:53, 20 June 2007 (UTC)FaUl
+
=== Booting from a USB Flash drive ===
  
Works well on a X31 type 2672-PG9, but with a big moment between starting update and the updating window -- [[User:Starox|Starox]] 22 Jul 2007
+
==== Updating the BIOS in MS-DOS mode ====
 +
(This process works for most Thinkpad models that has Windows XP, Windows Vista or Windows 7 OS)
  
And it worked for me on two X40 type 2371 -- [[User:Antialize|Jakob Truelsen]], 19 Jan 2007 -- BIOS: 2.07 1uuj21us.exe -- ECP: 1.62 1uhj10us.exe
+
1. Using HP USB Boot Utility, [http://blogs.oreilly.com/digitalmedia/2004/10/utility-to-make-usb-flash-driv.html create a bootable USB flash drive [http://www.bay-wolf.com/utility/usbkey/win98boot.zip DOS using Windows 98 Boot Disk Floppy Image].
  
Worked on X40 type 2386 -- [[User:Antialize|Galen Seitz]], 15 Feb 2008 -- BIOS: 2.08 1uuj22us.exe -- ECP: 1.62 1uhj10us.exe -- memdisk from syslinux 3.61
+
2. Extract the (*.ima) from the ISO BIOS image (e.g. [http://www.rarsoft.com WinRAR] will do this).
  
Not working for me on T43 type 2668-F7G -- [[User:Maus3273|Maus3273]] 20:48, 30 January 2007 (CET) -- BIOS: 1.29 1YUJ18US.IMG -- I got into the bios program, but the machine never restarts after initiating the upgrade.
+
3. Using a tool that can open .IMA files (such as [http://www.winimage.com/ WinImage]), extract all files to a temporary folder.
  
X41 type 2525-F8G -- [[User:ladoga|Lauri Koponen]], 11:08 16 Apr 2007<br>
+
4. Run the HP tool, select the USB device, I used FAT32,  create a DOS bootable disk and point at the win98boot folder - then "Start". Warning: this '''formats''' the USB flash drive and all data will be erased!
BIOS: 2.09 (74UJ15US.IMG), is no go. (hangs while initialising the actual flashing process) I tried with 2.07 (74UJ13US.IMG) and 2.06 (74UJ12US.IMG) aswell and they all failed in the very same fashion.<br>
+
ECP: 1.02 74HJ03US.IMG, works.
+
  
It works fine on R30 type 2656-64g, BIOS v.1.40 -- [[User:english.voodoo|Yuri Spirin]], 10 May 2007.
+
5. Once complete (you could test if it boots at this point), copy the extracted BIOS files from the temporary folder you created to the USB flash drive.
  
Workes fine on T40 type 2373 with cabextracted 1RUJ37US.IMG / 1RHJ10U2.IMG  and memdisk from syslinux 1:3.31-4 (Debian package version) -- [[User:Euphoria|Euphoria]] 00:10, 29 May 2008 (CEST)
+
6. Boot from USB flash drive by pressing F11 within the BIOS boot logo. At the DOS command prompt, type "updflsh" and then follow the prompts by pressing "Y" or Enter. Make sure that you have a fully charged battery pack and the AC Adapter is firmly plugged before proceeding with the BIOS update.
 +
'''DO NOT Power off the laptop or unplug the USB flash drive while the update is in progress or else update will fail and your computer will be unable to boot and system board may need to be serviced.'''
  
Works fine on R40 type 2723 with cabextracted 1OHJ11WW.IMG/1PUJ25US.IMG, memdisk from syslinux 3.70 (slackware 12.1) -- [[User:qunying|Qunying]] 21:28, 23 Jul 2008 (PST)
+
This process takes around 1-2 minutes. A long beep followed by a short beep will notify you that the update is complete and the system will automatically power off.
  
Worked perfectly on a T40 type 2373 with 1RHJ10U2.IMG (3.04, 2004-11-15) and 1RUJ37US.IMG (3.23, 2007-07-03) using cabextract and memdisk from syslinux 3:1.36-4ubuntu5. [[User:Morphics|Morphics]] 10:58, 20 Aug 2008 (BST)
+
7. Power on the laptop then enter the BIOS setup by pressing F1 and Load BIOS defaults.
  
Worked perfectly on a T41p type 2373 with 1RUJ37US.IMG (3.23, 2007-07-03) using cabextract and memdisk from syslinux 3.71 on gentoo linux. --[[User:Deggel|Deggel]] 21:03, 22 September 2008 (CEST)
+
==== Using grub4dos (also for Linux) ====
  
==Updating with Network Boot Image==
+
[http://grub4dos.sourceforge.net/wiki/ grub4dos] is a GNU GRUB fork with interesting features. One of them is the ability to boot ISO images directly off USB flash drives. Contrary to the name, GRUB for DOS works fine on Linux. Follow these steps:
 +
* Download the latest grub4dos package at http://download.gna.org/grub4dos/ (I needed 0.4.4 for my USB2 drive - 0.4.3 did not work.)
 +
* Unpack
 +
* Insert your FAT-32 formatted pendrive
 +
* Run <code>sudo ./bootlace.com /dev/sdX</code>, where /dev/sdX is the device name assigned to your pendrive (use <code>sudo fdisk -l</code> to figure this out). Be very careful to get the device correct or else you could overwrite your hard drive! This creates grub4dos boot sector in MBR of the flash drive.
 +
* Copy the files <code>grldr</code> and <code>menu.lst</code> to the root directory of your pendrive.
 +
* Convert the ThinkPad .IMG file to a .ISO file using <code>genisoimage -b 1yuj18us.img -c boot.catalog -o 1yuj18us.iso 1yuj18us.img</code>
 +
* Copy the ISO image to the root directory of your pendrive (e.g. <code>1yuj18us.iso</code>).
 +
* Edit <code>menu.lst</code> on the pendrive and include the following section (of course putting the appropriate ISO image name):
 +
<pre>
 +
title thinkpad-bios
 +
map (hd0,0)/1yuj18us.iso (hd32)
 +
map --hook
 +
chainloader (hd32)
 +
boot
 +
</pre>
 +
* Reboot and press F12 to select booting from USB.
 +
* If all went well, you should be able to boot the Thinkpad's ISO image and flash the BIOS. I tested it successfully on T400.
  
BIOS, Embedded Controller (EC), CD/DVD and Harddisk firmware disks can be booted
+
==== Manually creating a USB Flash drive in Linux ====
over the network with [http://syslinux.zytor.com/pxe.php PXELINUX] as part of the [http://syslinux.zytor.com/ SYSLINUX] package.
+
  
This requires that you have a DHCP and tftp server configured and setup properly on
+
Use "geteltorito" to extract the update image from ISO image, downloaded from Lenovo's drivers page. Write the extracted image to a USB Flash drive using dd. "geteltorito" is available in Ubuntu (at least in Trusty, 14.04) from package "genisoimage".
your network, and is probably not for the faint of heart.
+
* Install the genisoimage package: <code>sudo apt-get install genisoimage</code>
 +
* Extract the boot image from the ISO: <code>geteltorito g6uj14us.iso > biosupdate.img</code>
 +
* Install the boot image to USB Flash drive, make sure to install to the correct device! (device for me was /dev/sdb): <code>sudo dd if=biosupdate.img of=/dev/<yourusbflashdevice> bs=512K</code>
 +
* Reboot and press F12 to select booting from USB.
 +
* If all went well, you should be able to boot the Thinkpad's ISO image and flash the BIOS. Tested successfully on: X1 Carbon, X230.
  
Make sure the firmware bootdisk is in linux 'dd' format, as the self-extracting .exe disks
+
=== Booting from a Floppy ===
from the IBM website cannot be booted directly as such.
+
{{WARN|Using a floppy disk '''is NOT recommended'''.}}
  
This worked on the {{R31}}, {{X22}}, {{T21}}, {{T30}} and {{T41p}} with various firmware updates.
+
This is how IBM/Lenovo intended it.  Use their .exe files to create a bootable floppy with the flash update on it.  Boot from the floppy and there you go.
  
 +
So, why is it not recommended?
 +
# If something goes wrong, your ThinkPad may be permanently damaged
 +
# Floppy disk drives are not reliable
 +
# Floppy disks are not reliable
 +
# It only works with /dev/fd0, meaning it won't work with a USB floppy
  
On {{X22}}, works with EC 1.30 but NOT with BIOS 1.32
+
So, even though Lenovo is now offering "Linux diskette" updaters, that will create a bootable floppy under Linux, using a floppy is still not recommended. Besides, many people don't even ''have'' a floppy drive on their ThinkPad.
  
==Updating via "IBM Predesktop area", suitable for model X (not have CDROM and floppy)==
+
If you really want to do it with a floppy, some tips:
It's so difficult to update BIOS and ECP without cdrom, floppy disk.
+
* Use a clean (in the physical sense) floppy drive
Don't know the reason why I couldn't update BIOS and ECP(1QHJ08US and 1QUJ19US) for my IBM Thinkpad X31.Hmm, may be cause of the dividing partition on my hard disk, that is:
+
* Use new floppies
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
* Test floppies for errors before starting update process
<pre><nowiki>
+
* Have multiple copies of the update disks ready--if one should fail, replace it with a copy
Primary: ext3, ext3, ntfs
+
* Should DOS complain of a read error, '''only''' respond wth "Retry"
Extended: Ntsf, fat32
+
Bootloader: GRUB
+
</nowiki></pre></blockquote>
+
  
No problem, you can use this way to do it:
+
{{NOTE|Should the system encounter a disk read error during the flash process, and you select "Abort", your system could be permanently damaged.}}
* First, config in BIOS
+
In Security part:
+
# Remove all password of Subpervisor and Power on password
+
# Set Access IBM Predesktop Area to Normal
+
# Choose Enable "Flash BIOS updating by End User" in BIOS update Option.
+
  
In Config part:
+
==== Using UNetbootin ====
# Choose Enable for Network flash over Lan
+
  
* Second, download the newest version of BIOS update and ECP update
+
Unetbootin 422 worked with the image files unpacked with cabextract on my x31.
Running: The program extract all files to the folder. There is a .img file (1QUJ19US.IMG, 1QUJ08US.IMG) in each folder.
+
Copy the imformation content in that img file and paste it to one FAT partition(using winimage or TotalCmd to extract)
+
  
 +
{{HELP|How exactly did you do this? It failed for me. Does it work only with .IMG files that are converted to .ISO files, or can .ISO files provided by Lenovo also work (how?)}}
  
as seen All files in 1QUJ19US.IMG is extracted to D:\BIOS
+
=== Booting from a Network Boot Image ===
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
BIOS, ECP, CD/DVD and Harddisk firmware disks can be booted over the network with [http://syslinux.zytor.com/pxe.php PXELINX] as part of the [http://syslinux.zytor.com/ SYSLINUX] packageThis requires that you have a DHCP and tftp server configured and setup properly on your network, and is probably not for the faint of heart.
<pre><nowiki>
+
695,764  $018E000.FL1
+
163      0691.HSH
+
2,049    0691.PAT
+
163      0694.HSH
+
2,049    0694.PAT
+
163      0695.HSH
+
2,049    0695.PAT
+
2,049    06D0.PAT
+
163      06D1.HSH
+
2,049    06D1.PAT
+
163      06D2.HSH
+
2,049    06D2.PAT
+
163      06D6.HSH
+
2,049    06D6.PAT
+
2,049    06D8.PAT
+
697      CHKBMP.EXE
+
8,128    COMMAND.COM
+
26      CONFIG.SYS
+
24,860  FLASH2.EXE
+
26      LCREFLSH.BAT
+
170      LOGO.BAT
+
330      LOGO.SCR
+
111,925 PHLASH16.EXE
+
91,648  PREPARE.EXE
+
45      PROD.DAT
+
22,252  QKFLASH.EXE
+
9,923    README.TXT
+
4,260    TPCHKS.EXE
+
39,666  UPDTFLSH.EXE
+
6,958    UPDTMN.EXE
+
12,501  USERINT.EXE
+
15,254  UTILINFO.EXE
+
</nowiki></pre></blockquote>
+
  
And all files in 1QUJ08US.IMG are: D:\ECP
+
Make sure the firmware bootdisk is in linux 'dd' format, as the self-extracting .exe disks from the IBM website cannot be booted directly as such.
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
<pre><nowiki>
+
315,404 $018E000.FL2
+
8,000  COMMAND.COM
+
36      CONFIG.SYS
+
16,910  ECFLASH2.EXE
+
45      PROD.DAT
+
17,812  QKFLASH.EXE
+
990    README.TXT
+
4,260  TPCHKS.EXE
+
89,738  UPDTEC.EXE
+
31,134  UPDTFLSH.EXE
+
12,501  USERINT.EXE
+
15,226  UTILINFO.EXE
+
</nowiki></pre></blockquote>
+
  
* Okie, now plug AC Adapter, charge full battery to your laptop and continue third step:
+
This worked on the {{R31}}, {{X22}}, {{T21}}, {{T30}} and {{T41p}} with various firmware updates.  On the {{X22}}, it worked with ECP 1.30 but '''not''' with BIOS 1.32
  
** '''Flash BIOS first,'''
+
=After updating=
1. Power On, press blue button on keyboard: '''Access IBM'''
+
Lenovo recommends reseting your BIOS settings to their factory defaults after a firmware update.
  
2. On "Utilities", double click " Diagnostic disk"
+
Also, please consider updating the [[List of DMI IDs]] after updating your BIOS.
  
3. Your laptop will start PC-DOS, wait when this message appear:
+
= Special Cases =
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
* In one case, see ([[APM setup on a type 2379 ThinkPad T40]]), it was not possible to upgrade the BIOS from Windows XP; a downgrade to Windows 98 was required to successfully run the BIOS upgrade app. The symptoms in this case were that, once the files had been extracted to the hard disk, and the machine was to reboot into the upgrade app, it would beep and hang just before reboot, requiring a power cycle. Once the power was cycled, it would simply reboot back into XP without performing any BIOS upgrade actions. So even if you have Windows, you may still need to use the info on this page.
<pre><nowiki>
+
Please insert the first floppy diskette and
+
Press any key to continue
+
</nowiki></pre></blockquote>
+
  
4. Press Ctrl + Break, you will see :
+
== Updating Thinkpad X Series ==
<blockquote style="background: white; border: 1px solid black; padding: 1em;"><pre><nowiki>Terminate batch job (Y/N) ?</nowiki></pre></blockquote>
+
The special update instructions for {{X_Series}} Thinkpads are quite long. You can find them at the page [[BIOS_Upgrade/X_Series]].
  
5. Okie, press Y, you will get DOS prompt like D:\
+
== Updating without battery or with dead battery ==
{{NOTE|D:\ is my RAMDISK, C:\ is my disk format as FAT.!}}
+
  
6. Enter to c:\BIOS
+
This is a last-resort approach. Use this only if everything else fails.
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
<pre><nowiki>
+
c:
+
cd c:\BIOS
+
</nowiki></pre></blockquote>
+
  
7. Run FLASH2.EXE /u $018E000.FL1
+
The BIOS updater may refuse to update a BIOS without a battery, or if the battery charge is too low. In that case, extract the disk image with cabextract as per instructions above and dd it to an usb stick. (This will destroy the data on it, of course.) Acquire a pure DOS boot cd such as Windows 98 recovery CD and boot that.
  
8. Wait flash progress compelete and reboot.
+
Use F8 to abort the boot sequence of a windows 98 boot CD. If you need CD-ROM support, load CD-related things but say no to everything else. In particular, avoid loading himem.sys and doskey, as the presence of either program causes Phoenix bios flash tool phlash16.exe to abort.
** '''Flash ECP'''
+
Follow above instruction from step 1 to 5
+
  
6. Enter to c:\ECP
+
Change to the volume where flash2.exe and other tools are installed, and execute "flash2.exe /u". This should bypass the battery check and perform the flashing. If that doesn't work, check if the update disk contains a tool called "phlash16.exe". This can be used directly to flash the image, and the invocation is typically "phlash16 /exit $01c80000.fl1".
<blockquote style="background: white; border: 1px solid black; padding: 1em;">
+
<pre><nowiki>
+
c:
+
cd c:\ECP
+
</nowiki></pre></blockquote>
+
  
7. run UPDTFLSH.EXE $018E000.FL2
+
Updating the ECP with a dead battery or no battery presents a similar problem. For example, on the IBM ThinkPad X31, the normal command-line command to update the ECP would be UPDTFLSH ("UPDTFLSH $018E000.FL2").  But this utility checks for an installed and charged battery and will not let you update the ECP firmware if the battery is missing or not charged.  Instead, issue "QKFLASH $018E000.FL2".  This will bypass the test for the battery and allow the ECP firmware to be updated.  The same disclaimer applies here as for the BIOS: do this only as a last resort.  If there is a power failure during the update, you will likely brick your laptop.
  
8. Follow UPDTFLSH's instructions
+
This method won't work for the Thinkpad {{560X}} (and likely other older models). Since the 560X is a bit older, it won't be a big surprise if the battery is as dead as a dodo. Here's how to update the bios in this case: download the spsdi833 bios update and create the update floppy. If you have trouble creating this disk, [http://www.mediafire.com/?36o5a8buvbjx07o download an archive with the files] and put them on a floppy. Don't worry about making it bootable. Also, you will need a DOS bootdisk. A Windows 98 bootdisk will be fine. Boot the system with the W98 bootdisk, do not load CD-rom support. Remove the W98 bootdisk and put the disk with the BIOS update in the drive. If you would now run UPDTFLSH you would get the battery message, so don't do that. If you open UPDTFLSH.exe with a text editor, you would find some lines about UPDTROM. UPDTROM is the actual flash tool, but you can't simply run it just like that. Run the following:
  
9. Wait flash complete and auto turn off computer.
+
*updtrom /np /prep1
 +
*updtrom /np /prep2
 +
*updtrom /np /prep3
 +
*updtrom /np /romcmp /romflsh /prep4
 +
*updtrom /np /h8flsh /h8img /model
  
I done it on my IBM Thinkpad X31.
+
Yes, you need to run updtrom five times. Hold your breath and reboot the machine. It's done.
  
Enjoy,
+
Perhaps not all these lines are necessary, but to be sure I ran them all, and this worked for me. So I suggest you do the same. This could probably be done from the harddisk as well, but I did not test that.
  
Tested by nm.
+
For the {{i1400}} follow instructions on [http://www.motherboardpoint.com/flash-ibm-thinkpad-bios-w-o-battery-t143180.html this] website. It works not only for 2611 but for 2621 types too.
  
==After updating==
+
----
===DMI IDs===
+
Please consider updating the [[List of DMI IDs]] after (and before) updating your BIOS.
+
 
+
==Check List==
+
 
+
The following is important to remember:
+
# You must update '''both''' the Control Program and the BIOS at the same time if your current Control Program is not compatible with the new BIOS (see below)
+
# You must find versions of the Control Program and BIOS that are compatible.  Not all of them are, so follow the readmes on the IBM website carefully to determine which are.
+
# You must update the Control Program '''before''' you update the BIOS
+
  
When the Control Program '''and''' the BIOS need updating, have both update disks or CDs ready. Update the Control Program first and the system should switch itself off when finished. Insert the BIOS update disk and proceed to update the BIOS. When it's all finished, enter setup, reset the settings to their defaults and reboot. Enter setup again and tweak the settings as necessary.
+
{{footnotes|
 +
# For lots of detail on making and burning .iso files, see The Linux Documentation Project (tldp.org): [http://tldp.org/HOWTO/CD-Writing-HOWTO-3.html#ss3.1 3.1 Writing CD-ROMs (pure data)].
 +
}}

Latest revision as of 19:38, 1 November 2017

This page is meant to describe ways to update the BIOS on a ThinkPad that only runs Linux for users that don't have ready access to Windows. If you have Windows on your ThinkPad you can just boot into it and follow instructions on the Lenovo website.

Updating the BIOS in Linux (with few exceptions) is not officially supported by Lenovo. However there are work arounds.


ATTENTION!
By following any of the instructions here you are accepting the very real risk of turning your ThinkPad into a big expensive paper weight, as a firmware update gone wrong can create unfix-able problems. Proceed at your own risk!

Custom BIOS

Some ThinkPad fans have created Custom BIOSes to remove whitelists, disable annoying errors, do Fn-Ctrl keyswaps, and add more functionality. Check the Custom BIOS wikipage for more information.

  • X200, X60, T60, Macbook 2,1 - Libreboot - Based on Coreboot, this BIOS (approved by the FSF) removes all proprietary blobs to create Free Libre Open Source Laptops, where everything from the motherboard to the computer can use Open Source Software. Richard Stallman famously uses a Libreboot X60.
  • Sovem's Whitelist Removed BIOSes - A famous user from BIOS-mods.com, that removes mPCI whitelists from BIOSes upon request.
  • T61, R61, X61/X61s/X61T, X300 - Middleton's BIOS - Enables SATAII, removes whitelist, thermal fixes, Fn-Ctrl swap.
  • T43/T43p, R52, X41/X41T - TTav134's BIOS - Removes Error 2010 for aftermarket hard drives, and the BIOS whitelist.

Middleton's BIOS

A user on NotebookReview named 'Middleton' made these alternative BIOSes to enable SATA2 on certain Thinkpad models (X61/T61/R61/X300). These ThinkPads are limited to SATA1 in their BIOS even though the hardware is SATA2. This is a huge drawback for anyone wanting to use SSDs, because it is so much slower.

Also, it is not possible to install some wireless cards, because only certain models are whitelisted by IBM/Lenovo. Middleton's BIOS removes this limitation as well.

See the wikipage Middleton's BIOS for installation instructions, downloads, and more description.

Note: If your BIOS-Update tool says that no update is needed, then simply downgrade the Bios first: On Lenovo's drivers download page, the old Bios files are listed at the very bottom of the page.

Downloading New Firmware

ATTENTION!
Flashing the wrong firmware for your hardware may cause permanent damage to your ThinkPad. It is up to you to confirm that the firmware you are using is correct.

A list of links to firmware downloads can be found at BIOS Upgrade Downloads for most Thinkpad models. You can also check the Lenovo Support website's driver matrix.

Lenovo/IBM provides firmware upgrades in a variety of packages:

  • Diskette
  • Non-diskette
  • Linux diskette
  • BIOS Utility
  • Bootable CD

Not every type of package is available for every model.

The BIOS Utility and Bootable CD packages combine the BIOS and ECP firmwares. For the other packages, there is one for each firmware.

Help needed
Can an image be extracted from a "Linux diskette" .exe file?

The Linux diskette is just the Diskette package that runs on Linux instead of Windows/DOS. It's unknown if a boot image can be extracted from it.

You may need to try different packages to find the one from which you can extract a boot image.

Two Firmwares: BIOS and ECP

ATTENTION!
Flashing incompatible firmwares, or flashing them in the wrong order, may cause permanent damage to your ThinkPad.

It is important to understand that Thinkpads from IBM have two separate firmwares: the BIOS, and the Embedded Controller Program (ECP).

A given BIOS version will require a certain version of the ECP. You must read the Lenovo website and/or .txt files to confirm which BIOS is compatible with which ECP, and the order in which to update them.

Update Order

The Lenovo/IBM documentation is sometimes unclear about the order in which these two firmwares should be updated. When in doubt (i.e. IBM didn't provide specific instructions for your model or a particular firmware update), update the ECP first, and then the BIOS. Also, make sure to do the two updates immediately one after the other.

The EC firmware is usually much better at backwards compatibility than the BIOS.

NOTE!
Updaters for newer models take care of both BIOS and EC, and use automatically whatever sequence is needed, so you don't have to worry about it.

Installed Firmware

You can check the current BIOS and ECP versions on your ThinkPad as detailed here: BIOS Version

DMI IDs

Please consider updating the List of DMI IDs before (and after) updating your BIOS.

Updating Firmware

Firmware flasher program can run on DOS (Lenovo PC DOS) or Windows but, unfortunately, not Linux. So in theory there are two basic steps to update the firmware (either the BIOS or the ECP) on a ThinkPad not running Windows:

  1. Get or create a bootable image with supported OS
  2. Boot that image and, if not started automatically, ran flasher program

Recent Thinkpads have firmwares available as Bootable CD image, e.g., FILENAME.iso. If you have an optical drive there is no need to read this page any further: just download .iso image, burn it and boot to flash bios. If you are not that lucky, read on.

First you need to realize that there are different ways to boot DOS on PC (theoretically it is possible to boot Windows to ran flasher, but why?...): from internal hard drive, CD drive, USB Flash drive or, as the last resort, floppy drive. Easiest way is from internal hard drive, but you'd better avoid touching it until you don't want to loose files there. Booting from a Floppy is not recommended, so there are two best options to boot: CD drive or USB Flash drive.

Sparse instructions below provide you guidance how to do different parts of this pazzle but it's your duty to understand what to do and how to do that.

Using UEFI

Especially usable when CDROM is not available, tested on X140e, but should work in most recent firmwares as these supports UEFI, much simpler than older methods outlined in this and other pages.

You should have a USB mass storage device you can erase.

ATTENTION!
this will erase the USB mass storage device content.

1. Download BIOS update ISO image, we assume it is xxx.iso.

2. Extract bootable image using geteltorito tool:

$ ./geteltorito.pl -o xxx.img xxx.iso

3. Insert USB device, checkout its device, we assume /dev/sdX.

4. Dump content of image to USB device.

ATTENTION!
Double check the device name so you do not overwrite any other filesystem.

# dd if=xxx.img of=/dev/sdX

5. Reboot, enter BIOS setup, enable UEFI only (or 1st priority) at startup options, save and reboot.

6. Interrupt boot, press F12 and select USB mass storage device as boot source.

7. The BIOS update utility should run and you should succeed in flashing BIOS.

Create a bootable image

In case Lenovo does not provide your laptop with Bootable CD it is possible to create one from *discket packages.

Extracting an update image

ATTENTION!
Though this process has been successfully tested on many versions of .exe files found on IBMs website, that doesn't mean it will work for all of them. Proceed at your own risk. Consult the testing tables farther down of this page to see other users' experience with your model Thinkpad.
NOTE!
Lenovo has changed the packaging format. Old bios can be extracted with cabextract, new ones with innoextract.

Older .exe installers from Lenovo mostly appear to be just a wrapper license program around Windows .cab files (see BIOS-Bootsplash). If you install the Linux program cabextract you can expand these .cab files directly. For example, if you downloaded 1iuj13us.exe from Lenovo:

$ cabextract 1iuj13us.exe
Extracting cabinet: 1iuj13us.exe
 extracting 1IUJ13US.IMG
 extracting BIOSUPTP.EXE
 extracting DOBOOT.EXE
 extracting DOSBOOT.COM
 extracting DOSBOOT.SYS
 extracting DOSBOOT.VXD
 extracting DOSBOOT2.COM
 extracting ECTLUPTP.EXE
 extracting EFLASHAS.SYS
 extracting HDFWUPTP.EXE
 extracting IBMTPI.XML
All done, no errors.

The file we want is FILENAME.IMG, with "FILENAME" being the .exe. you downloaded. E.g., 1IUJ13US.IMG.

If this does not work for the Non-diskette .exe, try it on the Diskette .exe. It's reported, for example, that the Non-diskette .exe for BIOS version 3.23 for the T41p was not extractable, but the Diskette .exe worked perfectly, with $ cabextract delivering a .IMG file.

If cabeextract/innoextract fails

Diskette .exe for some older models can't be extracted using cabextract. For example for the latest BIOS of 390E one gets

spsdilc9.exe: no valid cabinets found

There is a simple way to solve this, by stripping the header off from the Non-diskette version. To do this, first you need to find the index for the first occurance of MSCF in the downloaded executable. This can be done with the following

strings -a -t d NO-DISKETT.EXE | awk 'offset=index($2,"MSCF"), (offset != 0) {print $1+offset-1}' | head --lines 1
4196

The command adds the byte offset of the matching line plus the index for the start of the MSCF on that line, thus the byte offset of MSCF, this number is usually 4196 Now we need to cut these header bytes off, this is done by a standard dd cut, the following cuts away the first 4196 bytes.

dd if=NO-DISKETTE.EXE of=out.cab iflag=skip_bytes skip=4196

The newly created out.cab should now work with cabextract

cabextract out.cab

A second alternative is to use Windows XP (works in VirtualBox too) together with Virtual Floppy Drive. Rund vfdwin.exe, go to the Driver tab and hit Install and Start. Then go to the Drive0 tab, click on Change and select A:. Finally, click on Open/Create, and click Create. This should give you a virtual floppy drive the .exe file will extract files to.

A third solution is to use QEMU with a DOS diskette image to run the disk extractor.

Testing the Image

You can test that FILENAME.IMG is really a floppy image by running:

# mkdir /tmp/mntfloppy

# mount -o loop FILENAME.IMG /tmp/mntfloppy

If a ls command on the image returns what looks like a DOS floppy, and no read errors were displayed, you have a pretty good chance that the image is usable. For example:

# ls /tmp/mntfloppy

$0195000.FL1  069580.PAT  06d2.HSH     IBMDOS.COM    TPCHKS.EXE
0691.HSH      06D0.PAT    06d6.HSH     LOGO.BAT      UPDTFLSH.EXE
0691.PAT      06D1.PAT    06d8.HSH     LOGO.SCR      UPDTMN.EXE
0694.HSH      06D2.PAT    CHKBMP.EXE   PHLASH16.EXE  USERINT.EXE
0694.PAT      06D6.PAT    COMMAND.COM  PREPARE.EXE   UTILINFO.EXE
0695.HSH      06D8.PAT    CONFIG.SYS   PROD.dat      lcreflsh.bat
0695.PAT      06d0.HSH    FLASH2.EXE   QKFLASH.EXE
069580.HSH    06d1.HSH    IBMBIO.COM   README.TXT

Unmount the image after you are done testing:

# umount /tmp/mntfloppy

Booting from update image

Now that you have a bootable image for the correct update for you hardware, you need to do is boot from that image to install the update.

There are different ways to do that:

Booting from a CD

Hint:
If there is a Bootable CD image available, e.g., FILENAME.iso, just download that, instead of mucking around with image files.

If you are going to update the firmware by booting from a CD, you need to turn FILENAME.IMG that you extracted above into an .iso file.

The El Torito Bootable CD Specification is a wonderful thing. Thanks to it, a bootable CD can be made with a bootable floppy image in such as way that the CD believes that it is a 2.88 MB floppy drive. This allows you to replace a boot floppy by a boot CD in nearly all situations.

It is very easy to create such a bootable CD ISO image in Linux using the mkisofs tool1. Run a command as follows:

# genisoimage -b 1WUJ25US.IMG -c boot.catalog -o bootcd.iso 1WUJ25US.IMG #or older mkisofs

Where *.IMG is the name of the image file extracted above. This creates a CD with one file on it and marks that file as the boot image.

You can now burn the bootcd.iso to a CD in your favorite CD-burning program.

ATTENTION!
By following any of the instructions here you are accepting the very real risk of turning your ThinkPad into a big expensive paper weight, as a firmware update gone wrong can create unfix-able problems. Proceed at your own risk!

Boot from the CD to update your firmware. Remember to have both BIOS and ECP firmware boot-CDs ready, as needed, and use them in the proper order.

Help needed
Please, report your success/failure with flashing BIOS from the manually cooked CD (from .IMG file) here: BIOS_Upgrade_success_failure#Booting_from_CD

Booting using GRUB

ATTENTION!
Many have warned not to use the SYSLINUX image-loader memdisk to boot firmware update images.
Help needed
Who are these "many"? Link to a discussion?

Once the bootable image, FILENAME.IMG, is extracted from the .exe, it can be booted directly through GRUB without the need of burning a CD, using the SYSLINUX image-loader memdisk.

Locate the memdisk file from the syslinux package. You can search for it with find:

# find /usr -name memdisk #or just use "dlocate memdisk" or "locate memdisk" if these programs are installed

If /usr/.../memdisk is not present, syslinux is not installed. You will need to install it to boot a .IMG from GRUB.

Copy both the FILENAME.IMG and memdisk files into /boot directory. For example:

# cp ./FILENAME.IMG /usr/share/syslinux/memdisk /boot/

Open /boot/grub/menu.lst in your favourite editor. Copy the active section into a new section, and edit the new section:

Parameter Instructions Example
title Pick a name for the new section. This will show up in the GRUB boot menu. title IBM ECP Update
root Do not change. This is the partition containing the /boot directory root (hd0,0)
kernel /boot/memdisk will allow you to boot an image file. kernel /boot/memdisk
initrd This is the name of the firmware-updater image file, e.g., 1IUJ13US.IMG initrd /boot/1IUJ13US.IMG

Do not modify the original section in /boot/grub/menu.lst, or you might not be able to boot back to the operating system.

If you have two firmware updates to do, you will need a section for each firmware's FILENAME.IMG in /boot/grub/menu.lst.

NOTE!
If both BIOS and ECP are to be updated, be sure to update them in the proper order.
ATTENTION!
By following any of the instructions here you are accepting the very real risk of turning your ThinkPad into a big expensive paper weight, as a firmware update gone wrong can create unfix-able problems. Proceed at your own risk!

Reboot your computer, entering the GRUB menu and selecting IBM BIOS Update, or whatever you named the new section in /boot/grub/menu.lst.

Booting image with GRUB2

GRUB2: booting floppy Image

With grub2, one would append the following to /boot/grub/grub.cfg :

menuentry "My BIOS Upgrade" {
set root=(hd0,0) #should match the others in your grub.cfg
linux16 /boot/memdisk
initrd16 /boot/1WUJ25US.IMG #or whatever yours is
}
Help needed
Please, report your success/failure with flashing BIOS from the manually cooked CD (from .IMG file) here: BIOS_Upgrade_success_failure#GRUB2:_Booting_floppy_Image
GRUB2: booting CD Image

You must first download the bootable iso file from the Lenovo Website.

On Debian and Ubuntu

Then, on Debian and Ubuntu, you can install the grub-imageboot package, then you just have to copy the iso file in /boot/images and run update-grub:

sudo apt-get install grub-imageboot
sudo mkdir -p /boot/images
sudo cp /home/youruser/Downloads/6uuj12uc.iso /boot/images
sudo update-grub
Manual method

Otherwise, copy the file 'memdisk' from the syslinux package to /boot. Also create a symlink, so you do not have to change the grub configuration for each bios upgrade:

sudo su -
cd /boot
cp /home/youruser/Downloads/6uuj12uc.iso .
cp /usr/share/syslinux/memdisk .
ln -s 6uuj12uc.iso biosupgrade.iso

Now create the boot entry:

cat >> /etc/grub.d/40_custom <<EOF
menuentry "Lenovo BIOS Upgrade" {
    set root=(hd0,1)  # <-- check for correct numbering
    linux16 /boot/memdisk iso
    initrd16 /boot/biosupgrade.iso
}
EOF
update-grub

Reboot an Select "Lenovo BIOS Upgrade".

For the next Bios Upgrade you'll just need to copy the new iso file to /boot and adjust the symlink.

Help needed
Please, report your success/failure with flashing BIOS from the manually cooked CD (from .IMG file) here: BIOS_Upgrade_success_failure#GRUB2:_Booting_CD_Image

Booting from a USB Flash drive

Updating the BIOS in MS-DOS mode

(This process works for most Thinkpad models that has Windows XP, Windows Vista or Windows 7 OS)

1. Using HP USB Boot Utility, create a bootable USB flash drive [http://www.bay-wolf.com/utility/usbkey/win98boot.zip DOS using Windows 98 Boot Disk Floppy Image.

2. Extract the (*.ima) from the ISO BIOS image (e.g. WinRAR will do this).

3. Using a tool that can open .IMA files (such as WinImage), extract all files to a temporary folder.

4. Run the HP tool, select the USB device, I used FAT32, create a DOS bootable disk and point at the win98boot folder - then "Start". Warning: this formats the USB flash drive and all data will be erased!

5. Once complete (you could test if it boots at this point), copy the extracted BIOS files from the temporary folder you created to the USB flash drive.

6. Boot from USB flash drive by pressing F11 within the BIOS boot logo. At the DOS command prompt, type "updflsh" and then follow the prompts by pressing "Y" or Enter. Make sure that you have a fully charged battery pack and the AC Adapter is firmly plugged before proceeding with the BIOS update. DO NOT Power off the laptop or unplug the USB flash drive while the update is in progress or else update will fail and your computer will be unable to boot and system board may need to be serviced.

This process takes around 1-2 minutes. A long beep followed by a short beep will notify you that the update is complete and the system will automatically power off.

7. Power on the laptop then enter the BIOS setup by pressing F1 and Load BIOS defaults.

Using grub4dos (also for Linux)

grub4dos is a GNU GRUB fork with interesting features. One of them is the ability to boot ISO images directly off USB flash drives. Contrary to the name, GRUB for DOS works fine on Linux. Follow these steps:

  • Download the latest grub4dos package at http://download.gna.org/grub4dos/ (I needed 0.4.4 for my USB2 drive - 0.4.3 did not work.)
  • Unpack
  • Insert your FAT-32 formatted pendrive
  • Run sudo ./bootlace.com /dev/sdX, where /dev/sdX is the device name assigned to your pendrive (use sudo fdisk -l to figure this out). Be very careful to get the device correct or else you could overwrite your hard drive! This creates grub4dos boot sector in MBR of the flash drive.
  • Copy the files grldr and menu.lst to the root directory of your pendrive.
  • Convert the ThinkPad .IMG file to a .ISO file using genisoimage -b 1yuj18us.img -c boot.catalog -o 1yuj18us.iso 1yuj18us.img
  • Copy the ISO image to the root directory of your pendrive (e.g. 1yuj18us.iso).
  • Edit menu.lst on the pendrive and include the following section (of course putting the appropriate ISO image name):
title thinkpad-bios
map (hd0,0)/1yuj18us.iso (hd32)
map --hook
chainloader (hd32)
boot
  • Reboot and press F12 to select booting from USB.
  • If all went well, you should be able to boot the Thinkpad's ISO image and flash the BIOS. I tested it successfully on T400.

Manually creating a USB Flash drive in Linux

Use "geteltorito" to extract the update image from ISO image, downloaded from Lenovo's drivers page. Write the extracted image to a USB Flash drive using dd. "geteltorito" is available in Ubuntu (at least in Trusty, 14.04) from package "genisoimage".

  • Install the genisoimage package: sudo apt-get install genisoimage
  • Extract the boot image from the ISO: geteltorito g6uj14us.iso > biosupdate.img
  • Install the boot image to USB Flash drive, make sure to install to the correct device! (device for me was /dev/sdb): sudo dd if=biosupdate.img of=/dev/<yourusbflashdevice> bs=512K
  • Reboot and press F12 to select booting from USB.
  • If all went well, you should be able to boot the Thinkpad's ISO image and flash the BIOS. Tested successfully on: X1 Carbon, X230.

Booting from a Floppy

ATTENTION!
Using a floppy disk is NOT recommended.

This is how IBM/Lenovo intended it. Use their .exe files to create a bootable floppy with the flash update on it. Boot from the floppy and there you go.

So, why is it not recommended?

  1. If something goes wrong, your ThinkPad may be permanently damaged
  2. Floppy disk drives are not reliable
  3. Floppy disks are not reliable
  4. It only works with /dev/fd0, meaning it won't work with a USB floppy

So, even though Lenovo is now offering "Linux diskette" updaters, that will create a bootable floppy under Linux, using a floppy is still not recommended. Besides, many people don't even have a floppy drive on their ThinkPad.

If you really want to do it with a floppy, some tips:

  • Use a clean (in the physical sense) floppy drive
  • Use new floppies
  • Test floppies for errors before starting update process
  • Have multiple copies of the update disks ready--if one should fail, replace it with a copy
  • Should DOS complain of a read error, only respond wth "Retry"
NOTE!
Should the system encounter a disk read error during the flash process, and you select "Abort", your system could be permanently damaged.

Using UNetbootin

Unetbootin 422 worked with the image files unpacked with cabextract on my x31.

Help needed
How exactly did you do this? It failed for me. Does it work only with .IMG files that are converted to .ISO files, or can .ISO files provided by Lenovo also work (how?)

Booting from a Network Boot Image

BIOS, ECP, CD/DVD and Harddisk firmware disks can be booted over the network with PXELINX as part of the SYSLINUX package. This requires that you have a DHCP and tftp server configured and setup properly on your network, and is probably not for the faint of heart.

Make sure the firmware bootdisk is in linux 'dd' format, as the self-extracting .exe disks from the IBM website cannot be booted directly as such.

This worked on the R31, X22, T21, T30 and T41p with various firmware updates. On the X22, it worked with ECP 1.30 but not with BIOS 1.32

After updating

Lenovo recommends reseting your BIOS settings to their factory defaults after a firmware update.

Also, please consider updating the List of DMI IDs after updating your BIOS.

Special Cases

  • In one case, see (APM setup on a type 2379 ThinkPad T40), it was not possible to upgrade the BIOS from Windows XP; a downgrade to Windows 98 was required to successfully run the BIOS upgrade app. The symptoms in this case were that, once the files had been extracted to the hard disk, and the machine was to reboot into the upgrade app, it would beep and hang just before reboot, requiring a power cycle. Once the power was cycled, it would simply reboot back into XP without performing any BIOS upgrade actions. So even if you have Windows, you may still need to use the info on this page.

Updating Thinkpad X Series

The special update instructions for X1, X1 Carbon, X1 Carbon 2nd, X1 Hybrid, X20, X21, X22, X23, X24, X30, X31, X32, X40, X41, X41 Tablet, X60, X60s, X60 Tablet, X61, X61s, X61 Tablet, X100e, X120e, X121e, X130e, X131e, X140e, X200, X200 Tablet, X200s, X201, X201i, X201s, X201 Tablet, X220, X230, X230i, X230s, X230 Tablet, X230i Tablet, X240, X240s, X300, X301 Thinkpads are quite long. You can find them at the page BIOS_Upgrade/X_Series.

Updating without battery or with dead battery

This is a last-resort approach. Use this only if everything else fails.

The BIOS updater may refuse to update a BIOS without a battery, or if the battery charge is too low. In that case, extract the disk image with cabextract as per instructions above and dd it to an usb stick. (This will destroy the data on it, of course.) Acquire a pure DOS boot cd such as Windows 98 recovery CD and boot that.

Use F8 to abort the boot sequence of a windows 98 boot CD. If you need CD-ROM support, load CD-related things but say no to everything else. In particular, avoid loading himem.sys and doskey, as the presence of either program causes Phoenix bios flash tool phlash16.exe to abort.

Change to the volume where flash2.exe and other tools are installed, and execute "flash2.exe /u". This should bypass the battery check and perform the flashing. If that doesn't work, check if the update disk contains a tool called "phlash16.exe". This can be used directly to flash the image, and the invocation is typically "phlash16 /exit $01c80000.fl1".

Updating the ECP with a dead battery or no battery presents a similar problem. For example, on the IBM ThinkPad X31, the normal command-line command to update the ECP would be UPDTFLSH ("UPDTFLSH $018E000.FL2"). But this utility checks for an installed and charged battery and will not let you update the ECP firmware if the battery is missing or not charged. Instead, issue "QKFLASH $018E000.FL2". This will bypass the test for the battery and allow the ECP firmware to be updated. The same disclaimer applies here as for the BIOS: do this only as a last resort. If there is a power failure during the update, you will likely brick your laptop.

This method won't work for the Thinkpad 560X (and likely other older models). Since the 560X is a bit older, it won't be a big surprise if the battery is as dead as a dodo. Here's how to update the bios in this case: download the spsdi833 bios update and create the update floppy. If you have trouble creating this disk, download an archive with the files and put them on a floppy. Don't worry about making it bootable. Also, you will need a DOS bootdisk. A Windows 98 bootdisk will be fine. Boot the system with the W98 bootdisk, do not load CD-rom support. Remove the W98 bootdisk and put the disk with the BIOS update in the drive. If you would now run UPDTFLSH you would get the battery message, so don't do that. If you open UPDTFLSH.exe with a text editor, you would find some lines about UPDTROM. UPDTROM is the actual flash tool, but you can't simply run it just like that. Run the following:

  • updtrom /np /prep1
  • updtrom /np /prep2
  • updtrom /np /prep3
  • updtrom /np /romcmp /romflsh /prep4
  • updtrom /np /h8flsh /h8img /model

Yes, you need to run updtrom five times. Hold your breath and reboot the machine. It's done.

Perhaps not all these lines are necessary, but to be sure I ran them all, and this worked for me. So I suggest you do the same. This could probably be done from the harddisk as well, but I did not test that.

For the i Series 1400 follow instructions on this website. It works not only for 2611 but for 2621 types too.



FOOTNOTES [Δ]
  1. For lots of detail on making and burning .iso files, see The Linux Documentation Project (tldp.org): 3.1 Writing CD-ROMs (pure data).