Rescue and Recovery
Consideration 6 of the Readme states:
"The Master Boot Record (MBR) must be configured properly for the Rescue and Recovery application to function properly. When possible, the Rescue and Recovery application attempts to ensure the proper configuration of the MBR. This can only occur if the Rescue and Recovery application is installed after other applications that requires the MBR."
Apparently, the MBR is not "configured properly" if LILO or GRUB have written it. The following is the case:
- The default bootloader seems to ignore the active bit and always boots the first partition instead
- The default bootloader contains code to catch a press of the appropriate button during bootup and launch the Rescue and Recovery application in that case
- Before launching the Rescue and Recovery application at system boot, the default bootloader changes the partition type of the Rescue and Recovery partiton to 0x0b, otherwise it changes it to 0x12 (to hide it from Windows)
- The Rescue and Recovery application assumes that the first partition contains Windows
- When booting from the Rescue and Recovery partition, it needs to have its type set (either by Thinkvantage or by GRUB) to 0x0b (FAT32) for the default bootloader to launch the Rescue and Recovery application.
Since neither LILO nor GRUB catch the press of the button (an undocumented mechanism anyway) it is not possible to launch the Rescue and Recovery application by pressing the appropriate button during system boot, once LILO or GRUB have altered the MBR for their boot procedure.
IBM provides a program to manage the Rescue and Recovery bootloader. It is located in C:\Program Files\IBM ThinkVantage\Common\BMGR or C:\Program Files\Common Files\Lenovo\BMGR. It can select the partition to boot, and also allows for rewriting the MBR if it was written by another bootloader. More information is needed about this program.
MBR written by GRUB
If the MBR was written by GRUB you can still use GRUB to launch the Rescue and Recovery application. However if you leave the type of the Rescue and Recovery partition to 0x12 (Compaq diagnostics), this will result in an error message "c000021a, Fatal System Error" if you try to launch it. To avoid that and to make sure the recovery partition always is of the right type, add a line to change the partition type to 0x0b to the Rescue and Recovery partition's entry in your /boot/grub/menu.lst. Assuming your Rescue and Recovery partition is the second partition, it could look like this: Please note that there are people who report that this didn't work, for example it didn't work on a Z61m 9450-3HG.
title IBM Rescue and Recovery root (hd0,1) parttype (hd0,1) 0x0b unhide (hd0,1) chainloader +1
Also add an unhide line here because we are going to hide the Rescue and Recovery partition on every boot of Windows, so we need to unhide it, when the recovery partition is booted. This is because if we don't hide the partition when booting Windows, it would be visible and accessable there and that's not what we want. So, assuming that Windows is on the first partition, the Windows entry could now look like this:
title Windows root (hd0,0) hide (hd0,1) chainloader +1
GRUB in a partition's boot sector
A way to have your Access IBM button still functional on bootup, is to create a separate /boot partition, install GRUB to that partition and make it active. This will leave the MBR untouched.
- In the BIOS, set the IBM Predesktop Area to 'Secure'.
- Boot your Linux distribution's installation CD.
- Follow the instructions and go through the regular installation process.
- Create a primary partition for /boot (the other stuff can go into the extended partitions) and when the time comes to install GRUB, make sure you install it into the boot sector of the boot partition.
- Set this boot partition as active.
Using the Windows Bootloader to Boot Linux
The NTLDR Windows bootloader can be configured to boot Linux in addition to Windows. The master boot record is unchanged, so the ThinkVantage Rescue and Recovery system boot functionality is preserved. This clever procedure was originally applied to Ubuntu Dapper Drake, and is generalized here.
1. Boot Windows and make product recovery disks. You will see this step repeated throught this wiki for good reason. The recovery disks can refresh your hard disk to its original factory state, getting you out of the trouble you might make in the next step.
2. Shrink the Windows NTFS partition to the size you like. You will need a bootable CD that is capable of resizing NTFS partitions. I have done this before with Knoppix, but this time I used Partition Magic (US$70).
3. Reboot into Windows to verify that the partition resize was successful.
4. Begin your Linux installation. Linux will see the Windows NTFS partition as /dev/sda1, and the Rescue and Recovery FAT32 partition as /dev/sda2. When the Linux installer asks you about GRUB, do not install GRUB in the MBR. Instead, install GRUB in the /boot partition (most likely /dev/sda3).
5. After the Linux installation is finished, reboot with a bootable Linux CD. The the "rescue mode" of your Linux installation CD #1 should work fine for this. Start the network if you plan to use FTP in step 7.
6. After you get a shell prompt, become root if necessary, and then write the first sector of the /boot partition (probably /dev/sda3) to a file using the dd command:
sudo -i dd if=/dev/sda3 of=grub.img bs=512 count=1
The resulting grub.img file should be 512 bytes long.
7. Transfer the grub.img file somewhere where you can read it from Windows. You can use removable media like a USB flash drive, or even FTP.
8. Reboot into Windows. Copy the grub.img file to c:\grub.img.
9. Save a copy of the c:\boot.ini NTLDR control file as, say, c:\boot.backup.ini. c:\boot.ini is read-only and hidden, so you will have to tell Windows to show hidden files, and turn off the read-only property on c:\boot.ini.
10. Edit c:\boot.ini. Append the line,
c:\grub.img="Linux GRUB Bootloader"
You may also want to change the default OS to c:\grub.img, and reduce the timeout to 5 seconds or so.
11. Reboot. Now the Windows boot menu should offer you a choice of "Linux GRUB Bootloader" or Windows XP. Choose "Linux GRUB Bootloader", and you will be taken to the GRUB boot menu, where you can select Linux, or even go back to the Windows boot menu.
12. When you want to use ThinkVantage Rescue and Recovery, push the ThinkVantage button upon system boot, just as you would have done had you not changed anything.
Older versions of Rescue and Recovery
Some Thinkpads (e.g., T23 and T30) do not come with a Recovery CD, but also do not support the Hidden Protected Area. These ThinkPads have an older version of Rescue and Recovery preloaded on the hard disk to implement the factory recovery function. Most of the comments above also apply to the older versions, with the following differences:
- The recovery partition type is 0x1c, hidden FAT32, LBA-mapped (or 0xc when unhidden).
- The boot manager program is in C:\IBMTOOLS\RECOVERY and only runs in a 16-bit DOS environment
name of this boot manager needed
- The IBM Predesktop area runs atop of Windows 98 (command-line) instead of WinPE
- IBM page on ThinkVantage Rescue and Recovery.
- Rescue and Recovery Readme
- IBM page about accessing the Recovery Partition if Linux has been installed and the F11 button no longer works
- IBM Rescue and Recovery repair diskette