How to control fan speed
This page discusses methods for controlling the system fan.
Using a patched kernel
The Patch for controlling fan speed provides a convenient interface via /proc/acpi/ibm/fan.
Manual speed control can be done through the patch for controlling fan speed:
#cat /proc/acpi/ibm/fan status: enabled level: auto speed: 4219 commands: enable, disable, level <level> (<level> is 0-7, auto or disengaged) #echo level 2 > /proc/acpi/ibm/fan #cat /proc/acpi/ibm/fan status: enabled level: 2 speed: 3142 commands: enable, disable, level <level> (<level> is 0-7, auto or disengaged)
Using a stock kernel
Linux Kernel 2.6.22 and Above (ibm-acpi has been replaced by thinkpad-acpi)
To enable fan control, the module parameter fan_control=1 must be given to thinkpad-acpi.
For example, in Ubuntu 8.04 (Hardy Heron), add the following to /etc/modprobe.d/options: options thinkpad_acpi fan_control=1
Having done so, reboot and you can use the following commands to control fan speed:
# echo level 0 > /proc/acpi/ibm/fan (fan off)
# echo level 2 > /proc/acpi/ibm/fan (low speed)
# echo level 4 > /proc/acpi/ibm/fan (medium speed)
# echo level 7 > /proc/acpi/ibm/fan (maximum speed)
# echo level auto > /proc/acpi/ibm/fan (automatic - default)
# echo level disengaged > /proc/acpi/ibm/fan (disengaged)
Older Linux Kernels (using ibm-acpi)
To enable fan control, the module parameter experimental=1 must be given to ibm-acpi. Then, you can control the fan by directly writing to the relevant embedded controller register, /proc/acpi/ibm/ecdump.
# echo 0x2F 0x00 > /proc/acpi/ibm/ecdump (fan off)
# echo 0x2F 0x02 > /proc/acpi/ibm/ecdump (low speed)
# echo 0x2F 0x04 > /proc/acpi/ibm/ecdump (medium speed)
# echo 0x2F 0x07 > /proc/acpi/ibm/ecdump (maximum speed)
# echo 0x2F 0x80 > /proc/acpi/ibm/ecdump (automatic - default)
# echo 0x2F 0x40 > /proc/acpi/ibm/ecdump (disengaged)
See the specifications below for the meaning of these modes.
On/off control using stock kernel
If you only wish to turn the fan on and off (with automatic control when it's on), you can use the following.
When loading ibm-acpi v0.11 with experimental switch (
# modprobe ibm_acpi experimental=1), it is possible to read and write the status of fan:
#cat /proc/acpi/ibm/fan status: enabled speed: 3580 commands: enable, disable #echo disable > /proc/acpi/ibm/fan cat /proc/acpi/ibm/fan status: disabled speed: 0 commands: enable, disable
When off, the fan will then never wake up. It is advised to use an automated control script to reduce the chance of hardware damage.
Automated control scripts
An ACPI fan control script can be used to override the firmware's fan algorithm with gentler, quieter version. It monitors the laptop's thermal sensors and sets the fan speed accordingly, according to customizable thresholds. For the default behavior, simply save as tp-fancontrol, make sure you've loaded thinkpad-acpi with the "fan_control=1" parameter, and run:
There is an distro independent daemon (http://projekte.f4.fhtw-berlin.de/trac/s0332819-linuxtools/wiki/), written in python. Packages are available for debian based linux systems.
A GTK GUI program (packaged for Ubuntu 7.10 and 8.04) may also help.
Automated program - Simple ThinkPad Fan Control
Written by Stanko, stanko [at] mfhinc [dot] net
This is program for controlling fans speed on IBM/Lenovo ThinkPads. It is written for Linux only. This program is written in C, using GTK GUI.
You are required to have the Linux kernel with 'thinkpad-acpi' patch. You must also enable manual control for your fans. For Linux 2.6.22 and above, you must add 'fan_control=1' as a module parameter to 'thinkpad-acpi'. For example, in Debian Lenny (and Ubuntu 8.04), you must add the following to "/etc/modprobe.d/options":
options thinkpad_acpi fan_control=1
Having done so, reboot. Now you'll be able to use this program easily.
Here is screenshot:
and direct download (src + i386 32bit binary). Please read README.txt file included in package. [tpfc0.5.tar.gz]
I wrote this for my own personal use, and thought that it would be a good idea to release it to the world, and hope that it will be useful to someone! Feel free to send comments, bug reports or a thanks to the e-mail above.
The following hardware behavior was discovered experimentally by Thinker and neither provided by nor confirmed by IBM/Lenovo. The following description may be inaccurate and may vary by model (see list of models above). The terminology probably does not match the one used by IBM/Lenovo engineers.
ACPI DSDT register HFSP (8 bits, offset 0x2F in the EmbeddedController address space, accessed through the standard EC interface at IO ports 0x62 and 0x66) is read/writable and has the following meaning:
Bits 7 6 5 4 3 2 1 0 --------------- Value 1 0 * * * * * * - automatic * 1 * * * * * * - disengaged 0 0 N N N N N N - manual (0..63; 0=disable fan, 1=min, ..., 7=max)
Changing modes may not be immediate on all ThinkPads. Later ThinkPad models seem to take at least 5s to start responding to a fan mode change, for example.
After boot, the HFSP register may not reflect the true state of the EC (on some models it reads 0x07 even though the EC is actually in automatic mode).
The embedded controller registers 0x84 (LSB), 0x85 (MSB) are the main fan tachometer, and report fan speed in RPM in everything since the A31 and maybe a little earlier. Not much is know about the tachometer in earlier models, or even whether they had one or not.
In automatic mode, the embedded controller sets the fan speed automatically according to system temperatures and some unknown algorithm.
Note that the ACPI DSDT may supplement this in some models. The X40, for example, changes the profile of speeds the automatic mode should use depending on battery status.
In manual mode, the fan level is forced to the given value and the EC will auto-regulate the fan to maintain at a (roughly) constant RPM, which is model-dependent. Manual speed levels 8-63 yield the same behavior as level 7, and the the ACPI DSDT uses level 7 for the emergency mode it enters upon critical CPU/GPU temperature, so apparently 7 is the real maximum level.
Disengaged (full-speed) mode
In disengaged mode, the embedded controller does not monitor the fan speed. It "disengages" the closed-loop control function that keeps track of fan speed, and uses an open-loop control function that ramps up the fan to its maximum speed (100% duty-cycle). The end speed is not stable, but it is often much faster than the maximum speed manual and automatic modes would set the fan to.
Most newer ThinkPads take quite a while (in excess of one minute) to fully enter disengaged mode. Exiting it is much faster. The A31 acts differently, and switches to disengaged mode as fast as it switches to other modes.
For some reason, the embedded controller may stop updating the tachometer registers while entering or exiting disengaged mode in some ThinkPad firmware versions (hence the EC tachometer registers will not be updated on these models while entering/exiting disengaged mode). Once it arrives at maximum speed, or once it gets back at closed-loop cruise speed, the embedded controller starts updating the tachometer registers again. Later T models such as the T43 have this problem, while the A31 does not.
The above was successfully tested on the following models:
- ThinkPad A31 (fan levels RPM: 0 = off, 1-2 = ~3280-3380 (!), 3-5 = ~3200, 6-7 = ~3380, "disengaged" = ~4000 (see NOTE above))
- ThinkPad R50 (highest manual level is 3; disengage mode works and reaches much higher RPM)
- ThinkPad R50p (fan levels RPM: 0 = off, 1-2 = ~3200, 3-5 = ~3500-3600, 6-7 = ~3700-3800, disengaged = ~5300)
- ThinkPad R51 (fan levels RPM: 0 = off, 1-2 = ~3150, 3-5 = ~3350, 6 = ~3750, disengaged = ~5100)
- ThinkPad R51e (fan levels RPM: 0 = off, 1-2 = ~3300, 3-5 = ~3800, 6 = ~4150, disengaged = ~5100)
- ThinkPad R52 (fan levels RPM: 0 = off, 1-2 = ~3350, 3-5 = ~3650, 6 = ~4250, disengaged = ~5245)
- ThinkPad R60 (fan levels RPM: 0 = off, 1-1 = ~2650, 3-5 = ~3300, 6-7 = ~3950, disengaged = ~4800)
- ThinkPad R60e
- ThinkPad T22
- ThinkPad T23 (low speed = ~2200, medium and maximum speed = ~4800; disengaged mode works at ~5800)
- ThinkPad T30
- ThinkPad T40 (fan levels RPM: 1-2 = ~2950, 3-5 = ~3600, 6-7 = ~4050; disengaged = ~5400)
- ThinkPad T41, T41p (fan levels RPM: 1-2 = ~2980, 3-5 = ~3500, 6-7 = ~4050; disengaged mode works at ~5100)
- ThinkPad T42, T42p (fan levels RPM: 1-2 = ~2900, 3-5 = ~3700, 6-7 = ~4700; disengaged mode works at ~5200)
- ThinkPad T43, T43p (fan levels RPM: 1-2 = ~3300, 3-5 = ~4100, 6-7 = ~4700; disengaged mode works at ~6450)
- ThinkPad T60 (fan levels RPM: 1-2 = 3000-3100, 3-5 = ~3600, 6-7 = ~4500; disengaged mode works at ~5500)
- ThinkPad T61 (fan levels RPM: 0 = off, 1-2 = ~2980, 3-5 = ~3330, 6-7 = ~3760; disengaged mode works at ~4500)
- ThinkPad X30 (level 0 = off, low = ~3900, medium = ~4200, maximum = ~4650, disengaged = ~5900)
- ThinkPad X31 (fan levels RPM: 0 = off, 1-2 = ~2850, 3-5 = ~3450, 6 = ~4050, 7 = ~4150; disengaged mode works at ~4975)
- ThinkPad X40
- ThinkPad X41
- ThinkPad X41 Tablet
- ThinkPad X60 (fan levels RPM: 7 = ~3700, disengaged ~4700)
- ThinkPad X61s
- ThinkPad Z60t, Z60m (fan levels RPM: 1-2 = ~1700, 3-5 = ~2800, 6-7 = ~3500)
- ThinkPad Z61m
- Thinkpad Z61p (fan levels 0-7, auto, disengaged; enable, disable; watchdog (untested))
Probably other models are supported too (please update this page if you confirm this; maintain some ordering too).
Models using a different interface
The following models also work, use a different access method which supported (only) via the /proc/acpi/ibm/fan of ibm-acpi. No need for patching.
- ThinkPad 560 (these models don't have a fan)