How to configure acpid
Basically, acpid just executes scripts residing in /etc/acpi/actions. Which script to launch at which event is configured in several files in /etc/acpi/events. All actions are documented in /var/log/acpid.
Sources of Information
$ man acpidholds detailed information on how to configure acpid.
- The ibm-acpi package includes example scripts in the config folder inside the tarball. They are a good starting point to adjust them to your needs.
- You also might want to have a look at the ACPI section of the Configs page or the Scripts repository.
- And you can find information about the event strings ibm-acpi generates for certain keys at the Special Keys HOWTO.
Example: go to sleep on lid close
To make the ThinkPad go to sleep when you close the lid, you need to add an event handler for the lid event and an action script that takes care of going to sleep and resuming.
The event script needs to be created within /etc/acpi/events and can have any name you like.
In this case we call it lid because it will trigger the lid event. Do
# vi /etc/acpi/events/lid and make it look like this:
event=button/lid action=/etc/acpi/actions/sleep.sh %e
The "event" line is a regular expression specifying the events we're interested in. You can determine what the event strings are from looking at /var/log/acpid after trying to suspend, close the lid, etc. . You can find information about the event strings ibm-acpi generates for certain keys at the Special Keys HOWTO.
The "action" line is the command to be executed when these events are dispatched. In this example we call the sleep.sh script residing in /etc/acpi/actions and pass the event description text using the %e placeholder.
Our example /etc/acpi/actions/sleep.sh script looks as follows:
#!/bin/sh # if launched through a lid event and lid is open, do nothing echo "$1" | grep "button/lid" && grep -q open /proc/acpi/button/lid/LID/state && exit 0 # remove USB 1.1 driver rmmod uhci_hcd # sync filesystem and clock sync /sbin/hwclock --systohc # switch to console FGCONSOLE=`fgconsole` chvt 6 /usr/sbin/radeontool light off # go to sleep sleep 5 echo -n "mem" > /sys/power/state # readjust the clock (it might be off a bit after suspend) /sbin/hwclock --adjust /sbin/hwclock --hctosys # reload USB 1.1 driver modprobe uhci_hcd # turn on the backlight and switch back to X radeontool light on chvt $FGCONSOLE
- The lid generates an event for both opening and closing thus requiring that we check its state and only act if it's closed.
- There have been problems encountered with the USB devices not working properly after a resume from suspend. To circumvent those we remove the USB driver prior to suspend and reload it afterwards.
- Note that the
# echo -n "mem" > /sys/power/stateline does not return until we are revived. So there is only one event generated and there is no need to check the state of anything.
- The console switching code in this script is a special solution for a problem where the backlight doesn't switch off on the T30 and some other models. Before going to sleep, these models switch to console mode which causes the backlight to come back on. So we preemptively switch to console mode and turn off the backlight using radeontool before going to sleep.
- If something doesn't work, your first action should be a
# tail /var/log/acpid. It will tell you a lot about what is going on. If it has "Permission denied" errors, check the permissions of your /etc/acpi/actions scripts (especially make sure that the executable bit is set). Also check the permissions for other involved files like i.e. device nodes.
- If your display doesn't come back on resume, look here.
- My X21 didn't reset the sleep LED (the small moon), it was blinking after the sleep, if you have the ibm-acpi kernel module loaded, you can switch it of after the sleep by appending this line to the script:
echo 7 off > /proc/acpi/ibm/led