- 1 ThinkPad T43 2687-DDU setup for Debian Etch
- 1.1 Kernel
- 1.2 Userland
- 1.2.1 Complex configuration issues
- 1.2.2 Simple configuration issues
- 1.2.3 udev rules
- 1.2.4 Kernel/module configuration
- 1.2.5 laptop-mode-tools
- 1.2.6 Suspend2
- 1.2.7 acpi events
- 1.3 Software that needs packaging
- 1.4 Software that could benefit from re-packaging
- 2 External Links
ThinkPad T43 2687-DDU setup for Debian Etch
This is an ongoing, spotty guide for an advanced Debian setup of a T43, focused on using absolutely all of its capabilities that can be used. It is not an installation guide, but rather a configuration guide. Refer to Debian for a list of pages with initial installation instructions.
When it is really usable, I will move it to some other far more public place in ThinkWiki.
Installing should be done using the latest Debian Etch debian-installer release. Anything else simply will not run on the ThinkPad.
Baseline kernel: Debian's latest 2.6.16 (220.127.116.11 with stabilization patches)
- Latest ipw2200 driver and ieee80211 layer:
- There are two ways to go about this: either disable IEEE 802.11 support (and thus ipw2200) in the kernel and build both modules out-of-tree (failure to do so will break the out-of-tree build), or update the kernel subsystems with more up-to-date files.
- The advantage of updating the kernel drivers instead of doing an out-of-tree build is that should there be any configuration options that require ieee80211 support, those will be available. On the other hand, it is a bit more difficult, as you will have to mess with Kconfig.
- copied files over the in-kernel files in include/net, drivers/net/wireless, Documentation/networking, net/ieee80211, thus replacing the old drivers with the new ones.
- ipw2200 often have extra options you need to enable, look in the toplevel Makefile and add them to drivers/net/wireless/Kconfig. They are usually bool types, so it is trivial to copy, e.g. IPW_DEBUG and rename to the new required options.
- SATA power-management
- freeze-block-queue patch (for HDAPS)
- ACPI update patches
- ACPI shutdown on resume patch
- TP SMAPI support
- Software Suspend 2
- Linuxant Conexant HSF modem driver
- nsc-ircc ISA PNP patch
Kernel setup tasks
- Make sure the following subsystems are modules (for suspend/resume)
- USB (especially EHCI_HCD and UHCI_HCD)
- HDAPS (may work compiled in, as well)
- Make sure the following subsystems are enabled and not modules (safety net)
- ThinkPad SMAPI
- Place the following modules on /etc/modules:
- Configure IrDA module options
- ipw2200 firmware needs to go in /lib/firmware. The module should be given the led=1 module parameter option
Complex configuration issues
You want to install and configure to your liking:
- kde/gnome power management thingies
- X.org power management on the video driver
Simple configuration issues
These are fairly simple minor things you might want to do:
install the procps package. Add the following lines to /etc/sysctl.conf:
install the sysfsutils package. Add the following lines to /etc/sysfs.conf
# ThinkPad battery charger defaults devices/platform/smapi/BAT0/start_charge_tresh=40 devices/platform/smapi/BAT0/stop_charge_tresh=85 devices/platform/smapi/BAT1/start_charge_tresh=70 devices/platform/smapi/BAT1/stop_charge_tresh=90 # Default frequency scalling governor devices/system/cpu/cpu0/cpufreq/scaling_governor=conservative
- udev extended network interface naming needs to be configured, order of tg3/ipw2200 won't be respected if /etc/modules.conf is read after udev did the PCI coldplugging
This is done in /etc/modprobe.d/ files. Install the setserial package.
Add a /etc/modprobe.d/thinkpad-t43 file there with this content:
# Intel Wireless, default to radio offline for safety and security options ipw2200 disable=1 led=1 hwcrypto=1 # IrDA alias irda0 nsc-ircc options nsc-ircc dongle_id=0x09 io=0x2f8 irq=3 dma=3 install nsc-ircc /bin/setserial /dev/ttyS1 uart none port 0 irq 0; /sbin/modprobe --ignore-install nsc-ircc
Install and configure laptop-mode-tools to your liking. If you really want to protect your HD when moving the ThinkPad around, laptop-mode-tools can help that dramatically by leaving the drive spun-down and parked most of the time.
On top of what is usually done for ThinkPads, remember to set the acpi_sleep=s3_bios kernel option if you have an ATI GPU. Suspend to RAM should be done using the default mode in ram.conf (RediSafe-like suspend-to-ram-with-backup-on-disk is possible, using Suspend2... but it takes 10 times more to suspend).
If you can do the suspend to ram without unloading any modules, it is much much faster. This heavily depends on the kernel, as a lot of drivers are still quite buggy.
# Suspend to RAM mode reminders UseSysfsPowerState mem SaveClock restore-only Unmount /media/* IbmAcpi yes
# Suspend to disk mode reminders UseSuspend2 yes Unmount /media/* UnmountFSTypes vfat msdos cifs smbfs ntfs nfs IbmAcpi yes
For suspend-to-ram (sleep)
#!/bin/sh # Check the reason we are running case "$1" in button/lid) # do not run with the lid open grep -q open /proc/acpi/$1/$2/state && exit 0 ;; esac exec /usr/sbin/hibernate -F /etc/hibernate/ram.conf
To sleep when the lid is closed:
event=button[ /]lid action=/etc/acpi/actions/sleep.sh %e
To sleep when fn+f4 is pressed:
event=button[ /]sleep action=/etc/acpi/actions/sleep.sh %e
event=ibm[ /]hotkey HKEY 0+80 0+1004 action=/etc/acpi/actions/sleep.sh %e
For hibernation (suspend-to-disk)
Requires that ibm-acpi has hotkeys enabled, mask 0x0800.
event=ibm[ /]hotkey HKEY 0+80 0+100[cC] action=/usr/sbin/hibernate
Software that needs packaging
- hdapsd (a bit crude, needs a lot of work still)
- ipw2200/ieee80211 need adopting, and since they clash terribly with in-kernel support, they will only work right if we either convert them to be patch-based, or to detect that the user built with in-kernel ieee80211/ipw2200 enabled and abort the out-of-tree compilation.
Software that could benefit from re-packaging
- hsfmodem: should be easy to build out-of-tree in another machine other than the one it will be installed at