Difference between revisions of "ThinkPad 11a/b/g/n Wireless LAN Mini Express Adapter"
|Line 34:||Line 34:|
There is now active development of a free driver [http://linuxwireless.org/en/users/Drivers/ath9k ath9k] that
There is now active development of a free driver [http://linuxwireless.org/en/users/Drivers/ath9k ath9k] that to support the draft 11n protocolis in the mainline kernel .and however , you'll have to [[How to install the development version of atk9k|jump through a few hoops]].
= Using the Windows Driver in Linux =
= Using the Windows Driver in Linux =
Revision as of 00:38, 5 December 2008
To determine the chipset your card uses, issue the following commands:
# update-pciids # lspci | egrep -i 'network|atheros|wireless' 03:00.0 Network controller: Atheros Communications, Inc. AR5418 802.11a/b/g/n Wireless PCI Express Adapter (rev 01)
If you get something different than above despite having the most current PCI IDs, please report it here!
For native Linux support, a development snapshot of the "madwifi" driver, which uses a non-free binary-only HAL, can be used. It does not support the draft 11n protocol, but will work in "legacy" 11g mode. Support for this chipset was initially planned for release 0.9.4, but this inclusion had to be postponed as a critical update with a bug fix for compilation with the 2.6.24 kernel was necessary before the pre-release trunk was sufficiently stable. Thus, it is still necessary to download the prerelease snapshot from trunk using subversion.
There is a howto, which describes the procedure for getting the snapshot to work.
There is an old ticket for this card at madwifi, #1001.
There is an new ticket for this card at madwifi-branch, #1243. Insert non-formatted text here
There is now active development of a free driver ath9k that aims to fully support the draft 11n protocol. It is available in the mainline linux kernel starting with 2.6.27 and there for automatically included in any distribution running this kernel (eg. Ubuntu Intrepid Ibex). The version in this latest kernel however does not support "aggregation" which basically means you will only see a slight increase in speed from the 11g protocol (mesured as 25 Mb/s vs 20Mb/s). If your distribution does not yet include this kernel (aheghm Debian), you'll have to jump through a few hoops.
Using the Windows Driver in Linux
If you have a weak stomach for pre-release software, you can always use "ndiswrapper" (>= 1.29) to wrap the Windows driver supplied by Lenovo. This isn't as bad as you think. It does work like a charm, but you may have problems if you're using a 64 bit kernel since it's not clear that a 64 bit windows XP driver exists (ndiswrapper currently doesn't support Vista drivers). Here's the Howto.
Non-Maskable Interrupt with madwifi
A number of folks have reported getting errors while using the experimental madwifi driver with the AR5418. After hours of flawless operation, the Kernel sometimes throws an NMI after which, the wifi dies. Aside from rebooting, suspending (to ram or disk) and resuming seems to be the only method to recover.
Uhhuh. NMI received for unknown reason b0 on CPU 0. You have some hardware problem, likely on the PCI bus. Dazed and confused, but trying to continue
wifi0: rx FIFO overrun; resetting wifi0: rx FIFO overrun; resetting wifi0: rx FIFO overrun; resetting
A possible preventitive measure is issuing the command
# iwpriv <device> bgscan 0
each time you load the driver. To make this change "permanent", you could add this command to your distribution's ifup networking scripts as described below.
Open up /etc/network/interfaces in a text editor and find the entry for your wireless device. Which should look something like
iface wlan0 inet manual wpa-driver madwifi wpa-roam /etc/network/wpa_supplicant.conf
and add the line
post-up iwpriv wlan0 bgscan 0
to the end of it where of course you substitute your interface name (e.g., "ath0") for "wlan0".
In addition to hard-switching the wireless card, the switch also generates an acpi event on transition from hi->lo and vice versa. It is however the same event in both directions.