* You should be have the wanted resolution in the properties of your DVI profile.
9 KB (1,406 words) - 18:39, 23 November 2008
...mpt, press F2. This will list available images. I used fb1024, because I wanted to use qtparted (graphical, fb1024 is framebuffer at 1024x768 vs fb800 is f
12 KB (2,107 words) - 05:31, 6 June 2008
...tfs partition, so the suggested "max" selection was the opposite of what I wanted.
23 KB (3,256 words) - 01:42, 26 March 2020
...since the ACPI standby-mode needs quite a lot of battery-power. However I wanted the hibernation mode. Coming up...
4 KB (694 words) - 16:56, 16 February 2009
...y I have no horror story and no complicated work arounds to report. But I wanted to let others know that CentOS 4 on this laptop is easy.
293 bytes (52 words) - 17:36, 24 November 2006
...ible. That is I didn't want to install a bunch of extra software. I just wanted an 'out of the box' configuration
I wanted to use WPA encryption. To get WPA you must use the wpasupplicant module.
4 KB (552 words) - 01:46, 15 October 2008
I wanted a dual-boot machine, but throwing caution to the winds, I decided not to cr
673 bytes (112 words) - 23:25, 22 September 2007
...oot, it wanted to run a filesystem check - let it run. (after booting, it wanted to reboot again because it thought some device had changed - went along wit
7 KB (1,142 words) - 18:21, 5 August 2011
I own an old IGATE 11M card (still fine for just surfing) I wanted to test on openSUSE 10.2. Unfortunately it did not work out of the box, so
51 KB (7,507 words) - 11:46, 8 January 2008
...both kernels were i586 so when I went to install the ATI Video driver, it wanted to update my kernel. I reinstalled with 'linux i686 as mentioned above and
15 KB (2,296 words) - 15:00, 27 July 2008
PS: I'm very sorry for this stupid looking guide, but I wanted to write it down, so it doesn't get lost. I got to know about it, through a
964 bytes (176 words) - 19:13, 20 February 2007
...t complete--I am editing it as I make progress on my installation. I just wanted to share the tricks I have discovered so far, and start a page where you ca
2 KB (304 words) - 09:40, 1 March 2008
Even though the X60s is fast core duo 1.8 Ghz machine I wanted to maximise efficiency so I choose Xubuntu.
3 KB (543 words) - 15:31, 7 July 2007
...mbols and I couldn't get it to work. Well, I forgot compiz for a while and wanted to just get the Xen HVM taste. So tried to use the xorg's nv driver and int
I had to crack my head to get this X in xen kernel. So made up my mind and wanted to give the generic VESA driver a shot and it worked!!! Finally some XServe
9 KB (1,330 words) - 17:36, 3 July 2007
I wanted to use all Space of the Harddisk, so I decided to kill the Rescue & and Rec
OK I really wanted to get hdapsd (Harddisk Active Protection) to work. I tried a lot of things
23 KB (3,641 words) - 01:45, 24 August 2008
I wanted to setup my account with a nonroot rpm build setup so I could recompile som
16 KB (2,567 words) - 14:22, 3 June 2008
now delete any line below the wanted threshold from the sorted file (i took "dash" as masker with 104kb)
...clude support for IPv6, firewall and PCMCIA so you'll need to add those if wanted.
16 KB (2,380 words) - 21:28, 24 December 2010
...ls to BAT0 when remaining capacity on BAT1 is less than 20%. Change .2 if wanted. Swap BAT0 and BAT1 if tp_smapi thinks the ultrabay is BAT0.
20 KB (3,084 words) - 17:42, 5 August 2011
So I did the backport of the driver (from 2.6.27) for myself, since I wanted to run the kernel 2.6.26 with Xen dom0 and 64 bits. Since this is not an ob
508 bytes (91 words) - 21:26, 20 December 2008
I wanted to give a try to GNOME and reinstalled the whole system. In the meantime a
2 KB (406 words) - 00:26, 23 February 2009