Difference between revisions of "Installing Slackware on a Thinkpad W520"

From ThinkWiki
Jump to: navigation, search
(Blanked the page)
 
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
== Installation ==
 
  
Slackware 13.37 64-bit installed like a breeze on a hot, humid day!  For the most part all of the essentials to get the system up and running on the W520 was detected and put into play with little or no intervention or editing of files on my end.
 
 
== Video ==
 
 
Coming from a W510, the W520 introduced me to the concepts of discrete and integrated graphics, as well as NVIDIA's Optimus technology.  Unfortunately because of NVIDIA's unwillingness to bring Optimus support to Linux, you have three choices.  You can use the integrated Intel HD graphics, NVIDIA's discrete graphics, or look into the bumblebee project [https://github.com/MrMEEE/bumblebee#readme here].  I went with the NVIDIA discrete graphics route with plans to try out the bumblebee project at a later time.  Make sure to specifically set your graphics option in the BIOS to discrete, otherwise Slackware/Linux will select integrated.
 
 
Instead of the open source nouveau driver I went with NVIDIA's binary, version 275.09.07.  With X.Org's X Server 1.9.5 in Slackware, xorg.conf is pretty bare these days as detection is done pretty smoothly at start.  Using NVIDIA's installer to create a default xorg.conf, the only things I added to that were
 
 
{{xorg.conf}}
 
 
 
The first decision is whether you want to use the NVidia discrete graphics (faster) or the Intel HD integrated graphics (more power-efficient). Both are more than fast enough for office graphics, the only noticeable speed difference is in 3D acceleration. You must set the graphics mode in the BIOS accordingly to discrete or integrated only. Do not leave it at the default "Optimus" as it is undocumented and unsupported.
 
 
{{NOTE|If you want stable 3D acceleration out of the box you should use the Intel integrated graphics.}}
 
The following notes refer to the NVidia discrete graphics only. Fedora uses the reverse-engineered Nouveau driver in this case, which currently is restricted to 2D graphics. If you need 3D acceleration, you have to install the binary-only NVidia drivers. The easiest way is to configure teh [http://rpmfusion.org/Configuration RPM fusion repository] and follow their [http://rpmfusion.org/Howto/nVidia NVidia HowTo]. This amounts to running
 
 
{{cmdroot|yum localinstall --nogpgcheck http://download1.rpmfusion.org/free/fedora/rpmfusion-free-release-stable.noarch.rpm}}
 
 
{{cmdroot|yum localinstall --nogpgcheck http://download1.rpmfusion.org/nonfree/fedora/rpmfusion-nonfree-release-stable.noarch.rpm}}
 
 
{{cmdroot|yum install kmod-nvidia}}
 
 
The backlight control does not work by default with the NVidia driver, to get it to work you have to add '''Option "RegistryDwords" "EnableBrightnessControl=1"''' to the Device section of your {{path|/etc/X11/xorg.conf}}.
 
 
== Networking ==
 
 
=== WiFi ===
 
 
I have the [[Intel Centrino Ultimate-N 6300]] card and it works out of the box.
 
 
=== Ethernet ===
 
 
The '''e1000e''' driver in Fedora 14 is too old for the ethernet chip. To get it to work you have to download and compile the [http://downloadcenter.intel.com/Detail_Desc.aspx?lang=eng&DwnldID=15817 updated driver] from Intel's web page. You don't have to recompile the whole kernel; Just unpack, make, and {{cmdroot|insmod ./e1000e.ko}}
 

Latest revision as of 01:57, 22 July 2011