Installing Slackware 11.0 on a ThinkPad R60
Slackware 11.0 requires a bit of work to get all of the major features of this notebook working. It may take some time, but don't be daunted, it can be done. This wiki is a work in progress (like all wiki's really) and i will try to make frequent updates until i have a fairly comprehensive guide, but i will especially focus on the issues that took some time (and head scratching) to resolve.
The R60 I am using has the following specifications:
- Intel Core Duo T2400 (1.83GHz)
- 512MB RAM
- 60GB 5400rpm SATA HD
- 15in 1400x1050 LCD
- Intel 945GM/GMS/940GML Graphics Controller
- Built in CDRW/DVD
- Intel Corporation PRO/Wireless 3945ABG
- Built in Modem
- Broadcom Corporation NetXtreme BCM5751M Gigabit Ethernet
- Built in fingerprint reader
- IEEE 1394 (firewire)
- 6c Li-Ion Battery
- Intel "High-Def" audio
- Suspend-to-RAM (finally)
- Dual core support (SMP)
- DVD / CDRW with DMA support
- Synaptics touchpad (with scroll functionality)
- The highest resolution in X: 1400x1050
- (most everything else i don't mention below)
Not Yet Working
- The special keys and key combos
- The thumbprint reader (this is due to the fact that Slackware does not use PAM for authentication, not driver problems)
- Although the Active Protection System accelerometer and deamon work, the patch for the 2.6.18 kernel to park the drive head was just released, and i haven't succeeded in making it function properly yet.
- OpenGL hardware acceleration seems to not be working
- Integrated security chip (getting errors trying to load kernel module tpm_atmel)
- Hibernation (to disk), i normally only use Suspend to RAM, but i believe there are pages devoted to hibernation
- Multi-headed VGA out
- S-Video out
- Firewire (probably works)
Before You Begin
Go into the BIOS and enable "compatibility mode" for the SATA controller
While you're there disable protection of the "recovery partition" if you know you won't be using Windows, and want to recover the extra 5GB (do at your own risk!) Make sure you have a basic understanding of lilo and how to recompile a kernel. Get the Slackware installation set (disks 1-3, but you may only need the first two)
I'll also assume that you are familiar with the basic steps of installing Slackware, if you're not, consult Slackware Installation
Begin by booting off disk 1 of Slackware 11.0. For the purposes of installation, Slackware uses the 2.4.33 kernel which will be installed by default. After the installation we'll be changing the kernel anyway, so it's okay to just install this default kernel for now.
I am using the 2.6.18 kernel, others may work, but this is what i will be focusing on. I recommend getting it from kernel.org instead of using the Slackware tarball in the /extra branch. (There's no good reason, just my own personal preference) Before starting the configuration you will need two thing:
- The ieee80211 kernel patch needed for the wireless drivers which can be obtained here
- The default slackware configuration file for the 188.8.131.52 kernel (which is in that kernel's tarball in the /extra branch) This is really only necessary if you're not a kernel pro, if you are, you don't need this.
Unpack the kernel and put it into the regular place (/usr/src) delete the linux link and relink it to the new kernel tree:
# rm /usr/src/linux
# ln -s /usr/src/linux-2.6.18 /usr/src/linux
Next unpack the ieee80211 stack, and patch it to the kernel source. From the ieee80211
# make patch_kernel
Next and most annoyingly, the files that were patched must be changed slightly for the modules to compile. In each .c file in the /usr/src/linux-2.6.18/net/ieee80211/ directory the line
must be changed to
Next the patch for the Advanced Protections System (HDAPS) will be applied in the usual way. Download the patch from here.
Copy the patch file to the /usr/src path (one directory below the kernel root.) Then apply it with:
$ patch -p0 <hdaps.patch
(Your filename may differ.)
Once you've completed this, copy the config-generic-smp-184.108.40.206 file from the Slackware kernel tarball to .config in the /usr/src/linux-2.6.18/ directory. Now run:
$ make menuconfig
or your favorite configure method.
Parameters that must be given special attention:
- Optimize for "Pentium 4"
- Make sure SMP is enabled
- Enable all ACPI functions that apply to the thinkpad, especially ibm-acpi (Compile these into the kernel, do not make them modules)
- SATA options
- tg3 Gigabit ethernet
- TPM atmel (which is the security chip)
$ make bzImage
$ make modules
# make modules_install
Copy the bzImage (along with your new .config) to your /boot directory, and add it to /etc/lilo.conf Next add the following line to lilo.conf in the appropriate image:
append = "libata.atapi_enabled=1 combined_mode=libata"
This causes the SATA driver to pick up the DVD drive instead of the IDE driver. This is important because the IDE driver won't allow DMA to be enabled properly. This is one major difference from the other Thinkpad 60's which have a slightly different SATA controller. The DVD drive will be /dev/sr0
After you've booted your shiny new kernel, we'll start configuring the system:
The first and most important thing to have working is your network connectivity. If you're using the gigabit ethernet card, this should already be working (so long as you compiled tg3). If you're like me, you need your wireless up as soon as possible.
The first thing to do is download the latest version of the ipw3945 drivers here.
Currently the Suspend option in Klaptop from KDE works reliably. Also, as long as the ACPI drivers are compiled in the kernel (not as modules) you can use the Lid-close suspend in KDE even with the wifi connected. When you open the lid, everything should resume properly, and the wifi will automatically reconnect to the network you had previously been connected to.
Follow the directions for setting up the touchpad here. Although it isn't mentioned explicitly, the Trackpoint can be used in conjunction with the Touchpad, simply follow the directions as though you have an additional external mouse, but set it's device file to /dev/psmouse as well. Both devices go through the same interface, this way you can use the Trackpoint as the pointing device and the Touchpad as a scrolling device. http://www.snpp.com/episodes/5F14
I'm using the pre-packaged i830 driver for XOrg, and i've found that it works nearly flawlessly in 16bpp mode, but in 24bpp more all kinds of (generally minor) screen corruptions occur. A program is necessary to enable the 1400x1050 resolution called 915resolution. This program writes the capability to the bios, at which point X is able to use it (providing that it's set up this way in your /etc/X11/xorg.conf file. I'm not using the external VGA nor S-Video at the moment, but fret not, this, as well as help setting up your xorg.conf file is available at Intel Graphics Media Accelerator 950.
- This guide is listed at the TuxMobil Linux laptop and notebook installation survey (IBM/Lenovo).