Difference between revisions of "How to use UltraBay batteries"

From ThinkWiki
Jump to: navigation, search
 
(15 intermediate revisions by 7 users not shown)
Line 1: Line 1:
{| width="100%"
+
#REDIRECT [[How to use Ultrabay batteries]]
|style="vertical-align:top;padding-right:20px;width:10px;white-space:nowrap;" | __TOC__
+
|style="vertical-align:top" |
+
ThinkPad laptops only charge/discharge one battery at a time. If you have two batteries present (a system battery and an [[UltraBay]] battery), the laptop will completely deplete the UltraBay battery before using the main battery.
+
|}
+
 
+
===Battery hot-swapping===
+
Switching between the batteries is instant, so if you pull the UltraBay battery from the bay when it is being discharged, the system will instantly switch to the main battery. You can therefore use the UltraBay battery to hot-swap the system battery (i.e., replace it without the need to reboot, hibernate or use an external power adapter).
+
 
+
You should issue {{cmdroot|echo eject > /proc/acpi/ibm/bay}} before removing the battery from the bay, especially if you are replacing it with a different device.
+
 
+
===Charging and discharging===
+
When charging, the system will completely charge the main battery before it starts on the UltraBay battery. When discharging, the system will completely discharge the UltraBay battery before it discharges the main battery. This greatly reduces the lifetime of the Ultrabay battery, and also reduces its usefulness for enabling hot-swapping of the system battery. There are two ways to prevent this:
+
 
+
* Keep an eye on the charge in the UltraBay battery and physically remove it from the bay when it gets too low (or release the eject lever- see below).
+
* Use the [[SMAPI support for Linux#Using_the_tp_smapi_module|tp_smapi]] module to control which battery is charged (<tt>inhibit_charge</tt> on the other battery) or discharged (<tt>force_discharge</tt>). This only works on some ThinkPad models - see the [[SMAPI support for Linux#Model-specific_status|model-specific status]].
+
 
+
===UtraBay eject lever===
+
It seems that you don't have to completely remove the battery from the bay to stop using it. If you release the eject lever, but don't actually pull the battery from the bay, the battery is still visible to the system, but the BIOS reverses the order of use and will completely deplete the main battery before using the UltraBay battery. The order of charging is not affected. Test machine: T23. May or may not work on other models.
+
 
+
===Reading the battery status under Linux===
+
 
+
====Using APM====
+
 
+
The second battery is correctly detected by the APM subsystem (if activated).
+
 
+
====Using ACPI====
+
 
+
The second battery is correctly detected by the ACPI subsystem (if activated). However, the Linux ACPI subsystem only scans for batteries on boot. This means that the second battery must be present at boot time, or you will not be able to get any info for it via {{path|/proc/acpi/battery/BAT1}}.
+
 
+
With kernel 2.6.14.2 (possibly only with [[ibm-acpi]]) there is a sysfs file: {{path|/sys/firmware/acpi/namespace/ACPI/_SB/PCI0/LPC/EC/BAT1/eject}}. There isn't one for BAT0, but {{cmdroot|cat /proc/acpi/battery/BAT0/*}} shows {{cmdresult|not present}} when there is no internal battery.
+
 
+
For BAT1 all the states go to 0, critical, etc. .
+
 
+
{{cmdroot|echo 1 > /sys/firmware/acpi/namespace/ACPI/_SB/PCI0/LPC/EC/BAT1/eject}} will remove {{path|/proc/acpi/battery/BAT1}} and turn off the UltraBay led. Interestingly the battery will still be discharging (charging not tested) until it is physically removed.
+
 
+
Also, if you compile the battery module of ACPI as a module, boot with the UltraBay battery present, remove the UltraBay battery (without doing the eject above), {{path|/proc/acpi/battery/BAT1}} is still there, while after {{cmdroot|rmmod battery && modprobe battery}} {{path|/proc/acpi/battery/BAT1}} is gone (BAT0 is back). Put the battery back in and {{path|/proc/acpi/battery/BAT1}} is still missing, do {{cmdroot|rmmod battery && modprobe battery}} and {{path|/proc/acpi/battery/BAT1}} is back.
+
 
+
If you boot without the second battery <tt>BAT1</tt> never appears in {{path|/proc}} or {{path|/sys}}.
+
 
+
If you eject using the sysfs file above, <tt>BAT1</tt> disappears from both {{path|/proc}} and {{path|/sys}} and never comes back.
+
 
+
====Using <tt>tp_smapi</tt>====
+
 
+
Independently of APM or ACPI, the battery status is also accessible through the [[tp_smapi]] driver. The <tt>tp_smapi</tt> kernel module provides battery status (and other features) via the sysfs interface in {{path|/sys/devices/platform/smapi/BAT<nowiki>{</nowiki>0,1<nowiki>}</nowiki>}}, and includes some information not accessible through APM or ACPI (e.g., cycle count and momentary power draw). The BAT1 interface is always present, regardless of whether the battery is present, was present on boot, or was ejected using the sysfs interface above.
+
 
+
Unfortunately, currently none of the standard battery monitoring scripts/applets use <tt>tp_smapi</tt>.
+

Latest revision as of 23:01, 15 February 2009