How to enable integrated fingerprint reader with BioAPI
This page describes the process of getting the integrated fingerprint reader to work under Linux, using bioapi and binary-only drivers. It is based on experiences in Ubuntu on a T43. The same works on Fedora 4 and 5, RHEL4, SuSE 9.3, SuSE 10, and Gentoo. Note that experimental open-source driver is available, see the apropriate page for details. |
Basic installation
Installing the bioapi framework
Automated installation script
The Script for enabling the fingerprint reader automates the installation of most components (bioapi framework, driver, pam_bioapi, pam setup, device permissions, pamtester and enrolling), for some Linux distributions.
Binary packages
Note that these packages only take care of this one section. If you can use one, you should do so and then proceed to the section entitled, Installing and Configuring the Driver.
Debian/ Ubuntu Dapper
- If you're using Debian Sid (the unstable branch) or Ubuntu Dapper Drake 6.06 LTS you can try the packages from Michael R. Crusoe's site, either version 1.2.3 (recommended) or older versions which might not work with the steps in this howto.
Gentoo
Gentoo now includes needed ebuilds. Just run
ACCEPT_KEYWORDS=~x86 emerge pam_bioapi
You can also grab the ebuild, or use the source-install procedure below.
Also see http://toe.ch/~tsa/ibm-fingerprint/ for alternative documentation on installing on Gentoo including ebuilds for all the packages used.
Fedora Core
RPM packages for Fedora Core and installation instructions are available here
Installing from source
For ubuntu (Gutsy) you'll need at least the: build-essential automake packages, or building will fail.
- Get the bioapi source:
- I could not compile bioapi with the graphical Qt tools. To do it manually, do the following:
$ tar xzf bioapi_1.2.3.tar.gz
$ cd bioapi-1.2.3
$ ./configure --with-Qt-dir=no
$ make
- and then as root
# make install
- If make install fails, be sure you're root and then:
# export LD_LIBRARY_PATH=/usr/local/lib
# make install
- and if you want to compile pam_bioapi for auth later
# cp include/bioapi_util.h include/installdefs.h imports/cdsa/v2_0/inc/cssmtype.h /usr/include
- Be aware that checkinstall will not work!
- (I got through configure with Qt, but got a cryptic build error. It all worked fine with Qt disabled as above)
- buzz: This is due to a wrong qt include path, set it manually in configure and everything should work.
- Bioapi (at least version 1.2.2) doesn't compile with GCC4. You need to patch it:
- This is neccessary to compile on SUSE 10.1 which it using gcc version 4.1.0.
$ wget http://upir.cz/linux/patches/bioapi-1.2.2-gcc4.patch
$ patch -p1 < bioapi-1.2.2-gcc4.patch
- Patch for gcc 4.1 is available here - http://cvs.pld-linux.org/cgi-bin/cvsweb/SOURCES/bioapi-c++.patch?rev=1.3
- By default, bioapi will install numerous files in /usr/local/{bin,lib,include}, including files with "self-explanatory" names such as /usr/local/bin/Sample. To prevent this pollution:
- Create a dedicated directory, for example /opt/bioapi .
- Append --prefix=/opt/bioapi to the above ./configure command.
- Append /opt/bioapi/bin to $PATH and /opt/bioapi/lib to $LD_LIBRARY_PATH.
- When installing the driver (below), tell it the new install path:
# sh install.sh /opt/bioapi/lib
Adjusting ldconfigs library search path
At least on Fedora or Aurox Linux 11, you may need to add /usr/local/lib to the library path so that the libraries referenced from pam_bioapi.so get picked up properly. The usual way to do this is adding it to the ldconfig configuration:
# echo '/usr/local/lib' > /etc/ld.so.conf.d/bioapi.conf
# ldconfig
Alternatively you can add it to the LD_LIBRARY variable.
If you see bioapi libs in the output of
# ldconfig -p
then it should work.
Installing and configuring the driver
Installing the driver
- Download TFMESS_BSP_LIN_1.0.zip from the UPEK support site and unzip it into a seperate folder, as it will not create one.
- Change to that folder and do as root:
# sh install.sh
- If you're running Gentoo, Debian or Ubuntu Dapper, use
# sh install.sh /usr/lib
For me it didn't work this way, but following did:
- sh install.sh /usr/local/lib
greetings, tec
- If that fails, it may be that make install failed up above -- try setting LD_LIBRARY_PATH, do the make install again, and come back here and try this again. You also need
mod_install
from bioapi in your PATH. - May there still occures and error, which means mod_install: command not found.
- Then login as root - not su!
- Do this:
# sh install.sh
- again. It should work. SU to root does not work since then the /usr/local/bin directory is not used per default.
Configuring permissions for non-root use
If you want to use PAM-aware applications like xscreensaver that are NOT running with root permissions (as opposed to login, gdm or other authentication mechanisms), you may need to do all or at least some of the things in this section. More details on what is necessary on which distributions would be greately appreciated.
- Create two groups, one for access to BioAPI files and the other for access to the usb files. (This is done for full generality; i.e., you may have other USB devices which you want accessable to other users, without exposing your BioAPI configuration to them). Add your normal user (the one you wish to use PAM-aware applications with) to both of these groups.
On Debian this is done with
# addgroup --system bioapi
# addgroup --system usbfs
# adduser yournormaluser bioapi
# adduser yournormaluser usbfs
On SUSE this is done with
# groupadd --system bioapi
# groupadd --system usbfs
# groupmod -A yournormaluser bioapi
# groupmod -A yournormaluser usbfs
On Mandriva this is done with
# groupadd -r bioapi
# groupadd -r usbfs
# usermod -G bioapi,usbfs yournormaluser
On Fedora this is done with
# groupadd bioapi
# groupadd usbfs
# usermod -G bioapi,usbfs yournormaluser
- (where
yournormaluser
is your normal user name). You will need to log out and log back in for this to take effect.
- Set permissions on the BioAPI config/registry directory:
# chown -R root:bioapi /usr/local/var/bioapi/
# chmod -R 770 /usr/local/var/bioapi/
- (change this path if you used an alternate BioAPI install directory above)
- Set permissions on the files in /proc/bus/usb:
# chown -R root:usbfs /proc/bus/usb
# chmod -R g+X /proc/bus/usb
# chown root:usbfs /proc/bus/usb/`lsusb | sed -ne "/0483:2016/s/Bus\ \(.*\)\ Device\ \(.*\):\ .*/\1\/\2/p"`
# chmod 660 /proc/bus/usb/`lsusb | sed -ne "/0483:2016/s/Bus\ \(.*\)\ Device\ \(.*\):\ .*/\1\/\2/p"`
- You may need to replace
lsusb
with its full path, which is something like/sbin/lsusb
or/usr/bin/lsusb
depending on your distro. It might be necessary to put these lines into a script which is run at startup and resume from suspend/hibernate.
In Fedora lsusb
is not installed by default. To intall it just type:
# yum install usbutils
- As an alternative to the
chown
/chmod
commands above, you can set mount options for usbfs with a line in /etc/fstab; an example would be
none /proc/bus/usb usbfs defaults,devgid=108,devmode=0660,busgid=108,busmode=0770,listgid=108,listmode=0660 0 0
- where 108 is replaced with the numerical group ID of the usbfs group (you can determine this with something like
cat /etc/group | grep usbfs | cut -d':' -f 3
). Make sure you only have one /proc/bus/usb entry in /etc/fstab. See themount(8)
manpage for more information on these options. This is "cleaner" but seems to have a few weird issues -- see the talk page for details.
- You may also have files in /dev/bus/usb, which the driver will try before /proc/bus/usb. If this is another usbfs mount point (
mount
shows a line containing/dev/bus/usb type usbfs
), then simply follow the above instructions with /dev/bus/usb rather than /proc/bus/usb. Otherwise, you may be running a new kernel (i.e. 2.6.15) that makes usbfs-like files available through /dev/bus/usb. - On systems running udev these files are dynamically created; you can configure their permissions by editing a udev config file. On Debian this is done by changing the usb_device line of /etc/udev/permissions.rules to read
SUBSYSTEM=="usb_device", MODE="0660", GROUP="usbfs"
- For the beta versions only, there is a logfile, which needs to exist with the proper permissions:
# touch /var/log/BSP.log && chown root:bioapi /var/log/BSP.log && chmod 660 /var/log/BSP.log
Miscellaneous configuration
- To increase the security level (minimize false accept rate), set this in /etc/tfmessbsp.cfg:
security-level="5"
Testing the driver and enrolling a fingerprint
To test the driver and generate the file containing your fingerprint information, you need a sample program included with the driver. The compilation steps below were discovered by trial and error; if they don't work for you, try the binary Sample
utility that came with the beta versions of the driver (i.e., TFMESS_BSP_LIN_1.0beta2.zip as mentioned above).
Go to the folder where you extracted TFMESS_BSP_LIN_1.0.zip and do:
# cd NonGUI_Sample
- Edit main.c and remove (or comment out) the line
#include "port/bioapi_port.h"
- then add the line
#include <stdlib.h>
# gcc -o Sample main.c -L/usr/local/lib -lbioapi100 -DUNIX -DLITTLE_ENDIAN
# ./Sample
- Note that Sample may only run as root, unless you've already configured the usbfs file permissions.
- You can try to "e"nroll (to record a fingerprint for an account) and then "v"erify (to test a fingerprint against the one it expects for an account).
- You'll save a step later if you use your own login username as the username to enroll here.
- If running
./Sample
produces the error message 'BioAPI_ModuleLoad failed, BioAPI Error Code: 6477 (0x194d)' - then uncommenting the line
- //BioAPI_SetGUICallbacks(gModuleHandle, NULL, NULL,TextGuiCallback, NULL);
- in main.c can help.
Login via pam_bioapi
The following explains how to add fingerprint authentiation to programs that use the PAM (Pluggable Authentication Modules) framework, such as Gnome's GDM and KDE's KDM and screensaver.
Getting required libs & tools
Installing pam_bioapi
- Prerequisites
- On SuSE 10, I needed to install the pam-devel RPM
- In general, you will need pam itself (standard for most distros) as well as the pam development files (probably an optional package for your distro).
- Get and compile the pam_bioapi module.
$ wget http://www.qrivy.net/~michael/blua/pam_bioapi/pam_bioapi-latest.tar.bz2
$ tar xjf pam_bioapi-latest.tar.bz2
$ cd pam_bioapi-0.2.1
$ wget http://badcode.de/downloads/fingerprint.patch
$ patch -p0 < fingerprint.patch
- If you want to, review the patch. In general you should review all code you download and compile, if possible.
$ ./configure --libdir=/lib && make
- and as root
# make install
- If you get 'configure: error: cannot find required header: security/_pam_macros.h' and are on a Debian-like system, do "apt-get install libpam0g-dev" and try again. If you are using a Mandriva distribution, do "urpmi libpam0-devel" instead.
- If you get 'configure: error: cannot find required header: security/pam_modules.h' and are on a Debian-like system, do "apt-get install libpam0g-dev" and try again.
- If you get 'configure: error: cannot find required header: sqlite3.h' and are on a Debian-like system, do "apt-get install libsqlite3-dev" and try again.
- If you get 'make: msgfmt: command not found' and are on a Debian-like system, do "apt-get install gettext" and try again.
- If you get 'PAM [dlerror: /lib/security/pam_bioapi.so: undefined symbol: BioAPIMemoryFuncs]' error in your syslog, replace 'LIBS = ' line in libpam_bioapi/makefile with the following (of course, replace /opt/bioapi/ with the path where you installed bioapi):
LIBS = -L/opt/bioapi/lib -lbioapi100 -lbioapi_mds300 -lmds_util
- Use the sample tool from the fingerprint reader to create <username>.bir (<username> must be the username you want to login with. gdm will probably break for any login name that has no .bir file).
- As root do:
# SERIAL=`BioAPITest | sed -ne "/Fingerprint/{n;n;s/^.*: \(.\{9\}\)\(.\{4\}\)\(.\{4\}\)\(.\{4\}\)\(.*\)/\1-\2-\3-\4-\5/gp}"`
# echo $SERIAL
should print something like{5550454b-2054-464d-2f45-535320425350}
now.- If it does, do:
# mkdir -p /etc/bioapi/pam/$SERIAL
# cp <username>.bir /etc/bioapi/pam/$SERIAL
- If not, you might just try
# SERIAL={5550454b-2054-464d-2f45-535320425350}
- as this value is hardcoded into the UPEK docs.
Configuring pam
The following part is distribution specific. On Ubuntu or SUSE you can modify /etc/pam.d/common-auth (on Gentoo and Fedora it is /etc/pam.d/system-auth) to look like this:
# # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # auth sufficient pam_bioapi.so {5550454b-2054-464d-2f45-535320425350} /etc/bioapi/pam/ password sufficient pam_bioapi.so {5550454b-2054-464d-2f45-535320425350} /etc/bioapi/pam/ auth required pam_unix.so nullok_secure
For Gentoo-Users - this allows you to attempt a password first. If you simply press enter, it then prompts for a fingerprints. Create a file named /etc/pam.d/bioapi. This also means that remote services, such as SSH keep working:
auth required pam_env.so auth sufficient pam_unix.so likeauth nullok auth sufficient pam_bioapi.so {5550454b-2054-464d-2f45-535320425350} /etc/bioapi/pam/ auth required pam_deny.so account required pam_unix.so session required pam_limits.so session required pam_unix.so
Now, simply replace "auth include system-auth" in all services that you wish to use fingerprint for with "auth include bioapi". For example, /etc/pam.d/kde by default contains
auth include system-auth auth required pam_nologin.so account include system-auth password include system-auth session include system-auth
Simply replace the first "system-auth" with bioapi and you can also get rid of KDE desktop lock with a fingerprint. If you do not wish to allow for "password fallback" then remove
auth sufficient pam_unix.so likeauth nullok
from /etc/pam.d/bioapi.
Note that sshd may pick up the fingerprint settings from /etc/pam.d/common-auth. I didn't want that, so I removed the "auth include common-auth" line from /etc/pam.d/sshd and replaced it with the lines that were originally in my /etc/pam.d/common-auth. That way most local services use the fingerprint reader, but sshd does not.
Another way to do this is to create a file (/etc/pam.d/bioapi for example) which contains the pam_bioapi.so
lines, and explicitly @include
this before /etc/pam.d/common-auth in the files for services which should use the fingerprint reader. In this case you should leave /etc/pam.d/common-auth alone.
In Fedora the original 'session' terms in /etc/pam.d/system-auth need to be kept.
To avoid that you can copy the default /etc/pam.d/system-auth to /etc/pam.d/sshd which will allow the sshd service to use the standard authentication procedure.
To enable normal password authorization to work with SUSE 10.3, edit the /etc/pam.d/sshd file. Remove all entries and replace them with:
auth required pam_env.so auth required pam_unix2.so auth required pam_nologin.so account required pam_unix2.so password required pam_pwcheck.so nullok password required pam_unix2.so nullok use_first_pass use_authtok session required pam_limits.so session required pam_unix2.so
(These entries are what common-auth normally does. Since we've changed common-auth around for bioapi, these need to be specified manually. -Ransak)
You can do some useful testing with pamtester
, which calls the pam modules as if it were a program of your choice. Examples:
# pamtester xdm yourusername authenticate
$ pamtester xscreensaver yourusername authenticate
where yourusername
is your username. Note that pamtester
should run as root if and only if the program in question does.
Application support
The implementation of fingerprint scanning support in the relevant applications varies.
Here is the behaviour of the most common ones:
- In gdm enter your username and there should pop up an (ugly) image to swipe your finger and... magic - you can login without a password.
- kdm doesn't give any visual indication, other than that the cursor stops blinking. Just swipe your finger and hope it lets you log in.
- In xdm, enter your username and a blank password, then swipe (there is no popup as well). Identification support for xdm can be achieved with this patch.
- The KDE screen saver in SUSE 10 requires you to enter an empty password (or select the correct user and then enter an empty password) in order to get the fingerprint prompt.
- For Fedora users, the redhat-config tools will crash if no root.bir presents. Also, there won't be any visual idication unless X server is properly configured for root to access. Just swipe your finger when the HDD stopped blinking or issue the following command in advance:
$ xhost +local:
- For RHEL4 users gdm, console (virtual terminal) logins and the xscreensaver all work
kdm support
To add graphical popup to kdm, you need following:
- Patch for pam_bioapi. This patch adds third parameter to pam_bioapi.so module, which is a name of file with additional environment variables that will be supplied to the UPEK driver.
# wget http://upir.cz/linux/patches/pam_bioapi-0.2.1-alter-environ.patch
# patch -p1 < pam_bioapi-0.2.1-alter-environ.patch
- Edit your Xsetup file (on SUSE 10 it's /etc/X11/xdm/Xsetup) and add these lines:
echo "XAUTHORITY=$XAUTHORITY" > /var/lib/xdm/kdm_env echo "DISPLAY=$DISPLAY" >> /var/lib/xdm/kdm_env
- In /etc/pam.d/xdm file, add /var/lib/xdm/kdm_env as a third parameter for pam_bioapi.so module:
auth sufficient pam_bioapi.so {5550454b-2054-464d-2f45-535320425350} /etc/bioapi/pam/ /var/lib/xdm/kdm_env
- On Ubuntu simply do:
echo "DISPLAY=$DISPLAY" >> /var/lib/kdm/kdm_env
- If you have created /etc/pam.d/bioapi then modify:
auth sufficient pam_bioapi.so {5550454b-2054-464d-2f45-535320425350} /etc/bioapi/pam/ /var/lib/kdm/kdm_env
Please note, that this won't work if you have more than one Xserver.
Make xscreensaver use the scanner
If you are using Gentoo, you can get a portage overlay with the necessary patches here: http://www.zzamboni.org/brt/files/xscreensaver-fingerprint-overlay.tar.gz
- Get the needed xscreensaver sources:
$ wget http://www.jwz.org/xscreensaver/xscreensaver-4.23.tar.gz
$ tar xzf xscreensaver-4.23.tar.gz
$ cd xscreensaver-4.23
$ wget http://www.nax.cz/pub/bioapi/2005/xscreensaver/xscreensaver-4.22_alternativeAuth.diff
mirror: http://zepan.org/files/xscreensaver-4.22_alternativeAuth.diff
For xscreensaver 5.00, you can get a patch here: http://www.zzamboni.org/brt/files/xscreensaver-5.00-alternativeauth.patch
- After reviewing the patch (it's small and straightforward), do
$ patch -p1 < xscreensaver-4.22_alternativeAuth.diff
The patch prevents xscreensaver from opening an authentification window and dispatches the authentification request to another program, in our case pam and pam_bioapi. It should apply with some offset, don't mind that. If it says something about rejected though, then there's a problem.
- Compile with
$ ./configure --with-pam && make
- If you receive an error like "Couldn't find X11 headers/libs" and are running a Debian-like system, try "apt-get install xlibs-dev"
- If you receive an error like "undefined reference to `XmuPrintDefaultErrorMessage'" then install the libxmu-dev package and run the previous line again and then install as root with
$ su -c make install
.
- Make sure that the newly compiled xscreensaver is used:
$ which xscreensaver
should return/usr/local/bin/xscreensaver
.
- In case it doesn't, try adjusting your PATH.
Common problems
Bioapi error #3
This is sometimes caused by improper permissions. The full error message is "BioAPI Error Code: 3 (0x3)".
However, at least on Gentoo, recent upgrades to glibc and gcc 4.1.1 caused Bioapi to break down due to some sort of incompatibility with bioapi registry. Reinstalling does not repair the issue automatically. However, you can still fix the issue manually, by removing /var/bioapi. You need to reinstall tfm-fingerprint driver after reinstalling bioapi so that the driver is properly re-registered. As root, type
# emerge -C bioapi
# rm -rf /var/bioapi
# emerge -av1 bioapi tfm-fingerprint