User:Piccobello/Wireless

From ThinkWiki
Jump to: navigation, search

My X31 has an Intel PRO/Wireless LAN 2100 3B Mini PCI Adapter built in.

Initially I thought it did not work. I could do:

# iwconfig eth0 essid <name> key <key>

and it seemed to work fine, but no tx power:

# iwconfig

eth0      IEEE 802.11b  ESSID:"rightname"  Nickname:"ipw2100"
          Mode:Managed  Frequency:2.462 GHz  Access Point: 00:0F:34:D5:90:E0
          Bit Rate=11 Mb/s   Tx-Power:off
          Retry min limit:7   RTS thr:off   Fragment thr:off
          Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX   Security mode:open
          Power Management:off
          Link Quality=100/100  Signal level=-58 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:184   Missed beacon:0

but

# iwconfig eth0 txpower on

Error for wireless request "Set Tx Power" (8B26) :
 SET failed on device eth0 ; Invalid argument.

Apparently this is not a problem! I can use it and still see TxPower:off so it's just not related.. I'd like to make KWirelessManager aware of this, it still shows it as disabled even though it gives me the correct speed, but as it's working it's not really a problem.. One thing: I added it to my /etc/network/interfaces file and ifup'd it manually

The reason is this ipw2100 bug, fixed in 1.1.5 (I have 1.1.2).

My /etc/acpi/wireless.sh with lots of debugging info

#!/bin/bash
# Find and enable/disable wireless devices

for DEVICE in /sys/class/net/*; do
    if [ -d $DEVICE/wireless ]; then
# $DEVICE is a wireless device. Check if it's powered on:
        echo $DEVICE power state `cat $DEVICE/device/power/state`
        if [ `cat $DEVICE/device/power/state` = 0 ]; then
# It's powered on. Switch it off.
            echo Switching off
            echo -n 3 > $DEVICE/device/power/state;
            echo $DEVICE power state `cat $DEVICE/device/power/state`
#Check SW kill switch status
#see /usr/src/linux-source-2.6.12/Documentation/networking/README.ipw2100
            if [ -e $DEVICE/device/rf_kill ]; then
                echo $DEVICE rf_kill `cat $DEVICE/device/rf_kill`
                if [ `cat $DEVICE/device/rf_kill` = 0 ]; then
                    echo -n 1 > $DEVICE/device/rf_kill
                    echo $DEVICE rf_kill `cat $DEVICE/device/rf_kill`
                fi
            fi
            echo 0
        else
# It's powered off. Switch it on.
            echo Switching on
            echo -n 0 > $DEVICE/device/power/state;
            echo $DEVICE power state `cat $DEVICE/device/power/state`
#Check SW kill switch status
#see /usr/src/linux-source-2.6.12/Documentation/networking/README.ipw2100
            if [ -e $DEVICE/device/rf_kill ]; then
                echo $DEVICE rf_kill `cat $DEVICE/device/rf_kill`
                if [ `cat $DEVICE/device/rf_kill` -gt 0 ]; then
                    echo -n 0 > $DEVICE/device/rf_kill
                    echo $DEVICE rf_kill `cat $DEVICE/device/rf_kill`
                fi
            fi
            echo 1
        fi
    fi
done