Difference between revisions of "Problem with video related system lockup II"
m (→Solutions) |
m (added r50p as affected) |
||
| (5 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | Thinkpads with the ATI 9600 video chip used in R50p, T42 and T42p can cause lock-ups. | |
This happens after about two years of use. | This happens after about two years of use. | ||
==Symptoms== | ==Symptoms== | ||
| − | Screen goes blank, requires hard reboot (power off-on) to get screen display. On boot may give one long, two short beeps POST code. Screen goes blank when laptop flexed, eg adjusting lid angle, squeezing around ultranav trackpad area, twisting, pressing on palmrest. POST code or screen blanking more prevalent after warm-up. Problem gets worse over time. Problem repeatable from first boot (bios) screen with tpad partially disassembled - | + | Screen goes blank, requires hard reboot (power off-on) to get screen display. On boot may give one long, two short beeps POST code. Screen goes blank when laptop flexed, eg adjusting lid angle, squeezing around ultranav trackpad area, twisting, pressing on palmrest. POST code or screen blanking more prevalent after warm-up. Problem gets worse over time. Problem repeatable from first boot (bios) screen with tpad partially disassembled - hdd, ultrabay, extra ram, wifi removed, kb, palm rest removed, but connected. See http://www.technotaste.com/blog/thinkpad-t42-ati-radeon-9600-driver-and-the-blue-screen-of-death-bsod |
| + | and | ||
| + | http://forum.thinkpads.com/viewtopic.php?t=33952 | ||
| + | for discussions of many similar symptoms. | ||
== Diagnosis == | == Diagnosis == | ||
| − | Bad solder joint on graphics chip. | + | Bad or broken solder joint on graphics chip. The chip is a ball grid array (BGA) package mounted to the system board. The problem is likely caused by an intermittent connection to the system board due to one or more bad or broken solder joints connecting the BGA to the system board. Thermal and/or mechanical movement breaks the connection, crashing the chip, yielding a blank screen or the BSOD. |
| − | |||
==Solutions== | ==Solutions== | ||
* Replace system board. | * Replace system board. | ||
| − | + | * Reflow the solder on the graphics chip: Remove the system board, take it to a board house that can reflow the BGA package, reassemble, cross fingers, test. There are a number of videos showing the process on YouTube. One of them: http://www.youtube.com/watch?v=vR8L3B3eDr0 | |
| − | * Reflow the solder on the graphics chip | + | * Place a supplement between the GPU Disipator and the keyboard metal, this will push the gpu to the systemboard, forcing a better contact. I placed about eight post-it's bended at the half. So far, so good. it works for me (eMaringolo). See it here: http://www.flickr.com/photos/emaringolo/373874916/ |
== See Also== | == See Also== | ||
[[Problem with garbled screen]] | [[Problem with garbled screen]] | ||
Latest revision as of 14:16, 26 January 2008
Thinkpads with the ATI 9600 video chip used in R50p, T42 and T42p can cause lock-ups.
This happens after about two years of use.
Contents
Symptoms
Screen goes blank, requires hard reboot (power off-on) to get screen display. On boot may give one long, two short beeps POST code. Screen goes blank when laptop flexed, eg adjusting lid angle, squeezing around ultranav trackpad area, twisting, pressing on palmrest. POST code or screen blanking more prevalent after warm-up. Problem gets worse over time. Problem repeatable from first boot (bios) screen with tpad partially disassembled - hdd, ultrabay, extra ram, wifi removed, kb, palm rest removed, but connected. See http://www.technotaste.com/blog/thinkpad-t42-ati-radeon-9600-driver-and-the-blue-screen-of-death-bsod and http://forum.thinkpads.com/viewtopic.php?t=33952 for discussions of many similar symptoms.
Diagnosis
Bad or broken solder joint on graphics chip. The chip is a ball grid array (BGA) package mounted to the system board. The problem is likely caused by an intermittent connection to the system board due to one or more bad or broken solder joints connecting the BGA to the system board. Thermal and/or mechanical movement breaks the connection, crashing the chip, yielding a blank screen or the BSOD.
Solutions
- Replace system board.
- Reflow the solder on the graphics chip: Remove the system board, take it to a board house that can reflow the BGA package, reassemble, cross fingers, test. There are a number of videos showing the process on YouTube. One of them: http://www.youtube.com/watch?v=vR8L3B3eDr0
- Place a supplement between the GPU Disipator and the keyboard metal, this will push the gpu to the systemboard, forcing a better contact. I placed about eight post-it's bended at the half. So far, so good. it works for me (eMaringolo). See it here: http://www.flickr.com/photos/emaringolo/373874916/
