Difference between revisions of "Patch for controlling fan speed"

From ThinkWiki
Jump to: navigation, search
(Hardware specs: - clearer presentation)
(Hardware specs: - IO ports)
Line 263: Line 263:
 
The patch relies on the following hardware behavior, which was discovered experimentally by [[User:Thinker|Thinker]] and neither provided by nor confirmed by IBM/Lenovo. The following description may be inaccurate and may vary by model (see list of models above). The terminology probably does not match the one used by IBM/Lenovo engineers.
 
The patch relies on the following hardware behavior, which was discovered experimentally by [[User:Thinker|Thinker]] and neither provided by nor confirmed by IBM/Lenovo. The following description may be inaccurate and may vary by model (see list of models above). The terminology probably does not match the one used by IBM/Lenovo engineers.
  
ACPI DSDT register _SB.PCI0.LPC.EC.HFSP (8 bits, offset 0x2F in the <tt>EmbeddedController</tt> address space)  
+
ACPI DSDT register _SB.PCI0.LPC.EC.HFSP (8 bits, offset 0x2F in the <tt>EmbeddedController</tt> address space, accessed through the standard EC interface at IO ports 0x62 and 0x66) is read/writable and has the following meaning:
is read/writable and has the following meaning:
 
 
   
 
   
 
  Bits  7 6 5 4 3 2 1 0
 
  Bits  7 6 5 4 3 2 1 0

Revision as of 13:29, 28 December 2005

Overview

This patch extends the ibm-acpi Linux kernel module to control fan speed. It can be used to reduce fan noise (both speed and pulsing) and to decrease fan power consumption.

When this patch is applied and the ibm-acpi module is loaded with the experimental=1 module parameter, the following new capabilities are added to /proc/acpi/ibm/fan:

  • # echo level LEVEL > /proc/acpi/ibm/fan sets a fan speed level between 0 and 7, where LEVEL=0 means fan off and LEVEL=7 is the fastest speed.
  • # echo level auto > /proc/acpi/ibm/fan tells the embedded controller to set the fan speed automatically according to system temperatures (this is the default).
  • # echo level disengaged > /proc/acpi/ibm/fan tells the embedded controller to disengage fan speed control (see specs below).
  • # cat /proc/acpi/ibm/fan shows the current fan level (in addition to the fan speed in RPM).

For example:

#cat /proc/acpi/ibm/fan
status:         enabled
level:          auto
speed:          4219
commands:       enable, disable, level <level>
                (<level> is 0-7, auto or disengaged)

#echo level 2 > /proc/acpi/ibm/fan

#cat /proc/acpi/ibm/fan
status:         enabled
level:          2
speed:          3142
commands:       enable, disable, level <level>
                (<level> is 0-7, auto or disengaged)

This patch is best used with an ACPI fan control script that monitors system temperature and sets the fan speed accordingly.

ATTENTION!
Overriding the system's automatic temperature control may cause permanent hardware damage. Even when using temperature monitoring software, it is not clear whether the software can access all temperature sensor accessible to the embedded controller and understand them correctly. Moreover, this patch relies on an undocumented hardware interface, and may thus have arbitrary effects (especially on models it wasn't tested on).

Models on which this patch works

  • ThinkPad T43, T43p (fan levels RPM: 1-2 = ~3300, 3-5 = ~4100, 6-7 = ~4700; disengaged mode works)
  • ThinkPad T42, T42p (fan levels RPM: 1-2 = ~2900, 3-5 = ~3700, 6-7 = ~4700)
  • ThinkPad T41, T41p (fan levels RPM: 1-2 = ~2980, 3-5 = ~3500, 6-7 = ~4050; disengaged mode works at ~5100)
  • ThinkPad T40 (fan levels RPM: 1-2 = ~2950, 3-5 = ~3600, 6-7 = ~4050)
  • ThinkPad T23
  • ThinkPad R52
  • ThinkPad R50 (highest manual level is 3; disengage mode works and reaches much higher RPM)
  • ThinkPad X41 Tablet
  • ThinkPad X31
  • ThinkPad Z60t (fan levels RPM: 1-2 = ~1700, 3-5 = ~2800, 6-7 = ~3500)

And probably additional models.

NOTE!
If you try this patch or the equivalent functionality in the ACPI fan control scripts, please update this page with your results.

Models on which this patch doesn't work

  • ThinkPad 600E, 600X, 770E, 770X (these use a different fan control interface)
  • ThinkPad 560 (these models don't have a fan)

The patch

for ibm-acpi 0.11

This also includes a minor fix (rename of device_add) to make ibm-acpi 0.11 compile on kernel 2.6.13.

--- ibm-acpi-0.11-orig/ibm_acpi.c	2005-03-17 12:06:16.000000000 +0200
+++ ibm-acpi-0.11/ibm_acpi.c	2005-10-26 06:21:57.000000000 +0200
@@ -1488,11 +1488,18 @@ static int fan_read(char *p)
 	} else {
 		/* all except 570, 600e/x, 770e, 770x */
 		if (!acpi_ec_read(fan_status_offset, &status))
 			len += sprintf(p + len, "status:\t\tunreadable\n");
-		else
+		else {
 			len += sprintf(p + len, "status:\t\t%s\n",
-				       enabled(status, 7));
+			              status ? "enabled" : "disabled");
+			if (status & 0x40)
+				len += sprintf(p + len, "level:\t\tdisengaged\n");
+			else if (status & 0x80)
+				len += sprintf(p + len, "level:\t\tauto\n");
+			else
+				len += sprintf(p + len, "level:\t\t%d\n", status);
+		}
 
 		if (!acpi_ec_read(fan_rpm_offset,     &lo) ||
 		    !acpi_ec_read(fan_rpm_offset + 1, &hi))
 			len += sprintf(p + len, "speed:\t\tunreadable\n");
@@ -1506,9 +1513,12 @@ static int fan_read(char *p)
 		len += sprintf(p + len, "commands:\tlevel <level>"
 			       " (<level> is 0-7)\n");
 	if (!gfan_handle)
 		/* all except 570, 600e/x, 770e, 770x */
-		len += sprintf(p + len, "commands:\tenable, disable\n");
+		len += sprintf(p + len, 
+		              "commands:\tenable, disable, level <level>\n"
+		              "         \t(<level> is 0-7, auto"
+		              "or disengaged)\n");
 	if (fans_handle)
 		/* X31, X40 */
 		len += sprintf(p + len, "commands:\tspeed <speed>"
 			       " (<speed> is 0-65535)\n");
@@ -1528,17 +1538,29 @@ static int fan_write(char *buf)
 			/* 570, 770x-JL */
 			if (!acpi_evalf(sfan_handle, NULL, NULL, "vd", level))
 				return -EIO;
 		} else if (!gfan_handle &&
-			   strlencmp(cmd, "enable") == 0) {
+			   ( (strlencmp(cmd, "enable") == 0) ||
+			     (strlencmp(cmd, "level auto") == 0) ) ) {
 			/* all except 570, 600e/x, 770e, 770x */
 			if (!acpi_ec_write(fan_status_offset, 0x80))
 				return -EIO;
 		} else if (!gfan_handle &&
 			   strlencmp(cmd, "disable") == 0) {
 			/* all except 570, 600e/x, 770e, 770x */
 			if (!acpi_ec_write(fan_status_offset, 0x00))
 				return -EIO;
+		} else if (!gfan_handle &&
+			   strlencmp(cmd, "level disengaged") == 0) {
+			/* all except 570, 600e/x, 770e, 770x */
+			if (!acpi_ec_write(fan_status_offset, 0x40))
+				return -EIO;
+		} else if (!gfan_handle &&
+		    sscanf(cmd, "level %d", &level) == 1 &&
+		    level >=0 && level <= 7) {
+			/* all except 570, 600e/x, 770e, 770x */
+			if (!acpi_ec_write(fan_status_offset, level))
+				return -EIO;
 		} else if (fans_handle &&
 		    sscanf(cmd, "speed %d", &speed) == 1 &&
 		    speed >= 0 && speed <= 65535) {
 			/* X31, X40 */
@@ -1751,9 +1773,9 @@ static int __init setup_notify(struct ib
 
 	return 0;
 }
 
-static int device_add(struct acpi_device *device)
+static int ibmacpi_device_add(struct acpi_device *device)
 {
 	return 0;
 }
 
@@ -1769,9 +1791,9 @@ static int __init register_driver(struct
 
 	memset(ibm->driver, 0, sizeof(struct acpi_driver));
 	sprintf(ibm->driver->name, "%s/%s", IBM_NAME, ibm->name);
 	ibm->driver->ids = ibm->hid;
-	ibm->driver->ops.add = &device_add;
+	ibm->driver->ops.add = &ibmacpi_device_add;
 
 	ret = acpi_bus_register_driver(ibm->driver);
 	if (ret < 0) {
 		printk(IBM_ERR "acpi_bus_register_driver(%s) failed: %d\n",

The author disclaims all warranty for this patch, and releases it to the public domain (meaning you may use and further distribute it under any terms you wish, including incorporating it into other software).

for ibm-acpi 0.12a as found in kernel 2.6.14

A slightly modified version which also keeps the lines in the format expected by the gkrellm plugin.

NOTE!
In order to patch the ibm_acpi.c file you have tu issue the following command: patch -p0 -l < fanpatch. The '-l' option is important because if the patch pasted here doesn't have any tabs any more. Another advice: Always try to patch the files first before really patching it. That is done by adding --dry-run to the command.


--- drivers/acpi/ibm_acpi.c.orig        2005-11-01 19:47:44.262270250 +0100
+++ drivers/acpi/ibm_acpi.c     2005-11-01 20:16:16.081252250 +0100
@@ -1465,6 +1465,7 @@ static int fan_read(char *p)
 {
        int len = 0;
        int s;
+       char status_read = 0;
        u8 lo, hi, status;

        if (gfan_handle) {
@@ -1477,9 +1478,11 @@ static int fan_read(char *p)
                /* all except 570, 600e/x, 770e, 770x */
                if (!acpi_ec_read(fan_status_offset, &status))
                        len += sprintf(p + len, "status:\t\tunreadable\n");
-               else
+               else {
                        len += sprintf(p + len, "status:\t\t%s\n",
-                                      enabled(status, 7));
+                                     status ? "enabled" : "disabled");
+                       status_read = 1;
+               }

                if (!acpi_ec_read(fan_rpm_offset, &lo) ||
                    !acpi_ec_read(fan_rpm_offset + 1, &hi))
@@ -1487,6 +1490,14 @@ static int fan_read(char *p)
                else
                        len += sprintf(p + len, "speed:\t\t%d\n",
                                       (hi << 8) + lo);
+               if (status_read) {
+                       if (status & 0x40)
+                               len += sprintf(p + len, "level:\t\tdisengaged\n");
+                       else if (status & 0x80)
+                               len += sprintf(p + len, "level:\t\tauto\n");
+                       else
+                               len += sprintf(p + len, "level:\t\t%d\n", status);
+               }
        }

        if (sfan_handle)
@@ -1495,7 +1506,10 @@ static int fan_read(char *p)
                               " (<level> is 0-7)\n");
        if (!gfan_handle)
                /* all except 570, 600e/x, 770e, 770x */
-               len += sprintf(p + len, "commands:\tenable, disable\n");
+               len += sprintf(p + len, 
+                             "commands:\tenable, disable, level <level>\n"
+                             "         \t(<level> is 0-7, auto "
+                             "or disengaged)\n");
        if (fans_handle)
                /* X31, X40 */
                len += sprintf(p + len, "commands:\tspeed <speed>"
@@ -1516,7 +1530,8 @@ static int fan_write(char *buf)
                        /* 570, 770x-JL */
                        if (!acpi_evalf(sfan_handle, NULL, NULL, "vd", level))
                                return -EIO;
-               } else if (!gfan_handle && strlencmp(cmd, "enable") == 0) {
+               } else if (!gfan_handle && ( (strlencmp(cmd, "enable") == 0) || 
+                               (strlencmp(cmd, "level auto") == 0) ) ) {
                        /* all except 570, 600e/x, 770e, 770x */
                        if (!acpi_ec_write(fan_status_offset, 0x80))
                                return -EIO;
@@ -1524,6 +1539,17 @@ static int fan_write(char *buf)
                        /* all except 570, 600e/x, 770e, 770x */
                        if (!acpi_ec_write(fan_status_offset, 0x00))
                                return -EIO;
+               } else if (!gfan_handle &&
+                          strlencmp(cmd, "level disengaged") == 0) {
+                       /* all except 570, 600e/x, 770e, 770x */
+                       if (!acpi_ec_write(fan_status_offset, 0x40))
+                               return -EIO;
+               } else if (!gfan_handle &&
+                   sscanf(cmd, "level %d", &level) == 1 &&
+                   level >=0 && level <= 7) {
+                       /* all except 570, 600e/x, 770e, 770x */
+                       if (!acpi_ec_write(fan_status_offset, level))
+                               return -EIO;
                } else if (fans_handle &&
                           sscanf(cmd, "speed %d", &speed) == 1 &&
                           speed >= 0 && speed <= 65535) {

The author disclaims all warranty for this patch, and releases it to the public domain (meaning you may use and further distribute it under any terms you wish, including incorporating it into other software).

Ideas for improvement

  • When fan speed is controlled from userspace (e.g., by the ACPI fan control scripts), the userspace component may die (for whatever reason) leaving the fan at a low speed, potentially leading to damage. We can add a watchdog to the kernel component, which resets the fan to Embedded Controller control (leve: auto) if /proc/acpi/ibm/fan was not written to for N seconds.

Controlling the fan without this patch

If you have the ibm-acpi module loaded with experimental=1, you can control the fan without patching the kernel by directly writing to the relevant embedded controller register using /proc/acpi/ibm/ecdump.

For example:

# echo 0x2F 0x04 > /proc/acpi/ibm/ecdump

will set the fan to manual mode 4 (see the specifications below).

Hardware specs

The patch relies on the following hardware behavior, which was discovered experimentally by Thinker and neither provided by nor confirmed by IBM/Lenovo. The following description may be inaccurate and may vary by model (see list of models above). The terminology probably does not match the one used by IBM/Lenovo engineers.

ACPI DSDT register _SB.PCI0.LPC.EC.HFSP (8 bits, offset 0x2F in the EmbeddedController address space, accessed through the standard EC interface at IO ports 0x62 and 0x66) is read/writable and has the following meaning:

Bits   7 6 5 4 3 2 1 0
       ---------------
Value  1 0 * * * * * *  - automatic
       * 1 * * * * * *  - disengaged
       0 0 N N N N N N  - manual (0..63; 0=disable fan, 1=min, ..., 7=max)

In automatic mode, the embedded controller sets the fan speed automatically according to system temperatures and some unknown algorithm.

In manual mode, the fan level is forced to the given value and the EC will auto-regulate the fan to maintain at a (roughly) constant RPM, which is model-dependent. Manual speed levels 8-63 yield the same behavior as level 7, and the the ACPI DSDT uses level 7 for the emergency mode it enters upon critical CPU/GPU temperature, so apparently 7 is the real maximum level.

In disengaged mode, the embedded controller does not read the fan RPM (hence EmbeddedController offset 0x84 is not updated), and does not maintain a stable fan speed. When disengaged mode is entered the fan speed is not immediately changed (except if the fan was disabed, in which case it is turned on at a low level). However, once in disengaged mode, fan speed will slowly increase to beyond the maximum manual level (this may cause hardware damage!).

After boot, the register may not reflect the true state of the EC (on some models it reads 0x07 even though the EC is actually in automatic mode).

Hint:
Apparently the pulsing fan noise experienced by some users can be cured by repeatedly running 2-4 seconds of manual control followed by 0.5-1 seconds of disengaged mode. The pulse occurs when the the embedded controller computes the fan speed and adjusts the fan voltage adaptively every few seconds (~4.8sec for the ThinkPad T43); the aforementioned mode switching doesn't give it a chance to do so. One of the ACPI fan control scripts implements this solution.

Tools based on this patch or specs