Problems with ACPI suspend-to-ram

2006-06-18T19:59:18Z

Uberpenguin: /* Troubles on resume */

The following glitches may or may not occur in relation to suspending to RAM:

==Troubles on suspend==
;Permissions:If your suspend is failing, and a {{cmdroot|tail /var/log/acpid}} shows "Permission denied" errors, be sure that your new ACPI event and action scripts have the appropriate permissions.

;Broken sysfs interface:You may experience problems when using {{cmdroot|echo standby > /sys/power/state}} or {{cmdroot|echo mem > /sys/power/state}} (machine goes to sleep and wakes up immediately). This can be avoided by using {{cmdroot|echo -n 3 >/proc/acpi/sleep}} to get it to sleep. This can be also happen if hotplug daemon is still running.

;MySQL daemon running:If you're running MySQL, sleep may also not work, so stop MySQL first, then sleep. Remember to restart MySQL when you wakeup.

;LCD backlight remains on during sleep:When your system is equiped with a Radeon Mobility graphic controller your [[Problem with LCD backlight remaining on during ACPI sleep|LCD backlight may not turn off automatically]]. Use [[radeontool]] to switch off your backlight prior suspend in your sleep action script.

;High power drain during sleep:Also, you might want to take note of the [[Problem with high power drain in ACPI sleep]].

==Troubles on resume==
;Blank display on resume:When resuming from a suspend-to-ram the display might remain black or might only show the pre-suspend output (the system is still rebootable via {{key|ctrl}}{{key|alt}}{{key|del}}). See [[Problem with display remaining black after resume]] for solutions.
;Broken hardware support after resume:
:*The '''serial port''' of the port replicator might not work after resume.
:*The '''parallel port''' might not work after resume. A possible fix is to unload and reload the parallel port drivers: {{cmdroot|rmmod lp parport_pc parport; modprobe lp}}.
:*Problems with the '''CD-RW/DVD drive''' after wake up from ram have been experienced.
:*There is a known Problem regarding '''battery info''' after suspend to RAM. A [http://www.ussg.iu.edu/hypermail/linux/kernel/0511.0/2429.html small patch] exists for kernels 2.6.14/2.6.15.
:*On {{X20}} and {{X21}} (and possibly other) models, the '''sleep LED''' is not reset properly on resume and will keep blinking. If you have the [[ibm-acpi]] kernel module loaded with the <tt>experimental=1</tt> option, you can switch it off on resume by appending the following line to your suspend script:
echo 7 off > /proc/acpi/ibm/led

;Crash on resume:
:*When using '''older ATI proprietary drivers''' a crash on resume can be solved by using [http://freshmeat.net/projects/vbetool/ vbetool]. See the example suspend script [[Problem with display remaining black after resume#Solution for ThinkPads with Intel I830 Chipset]]. This is no longer necessary with recent revisions of the ATI proprietary driver.
:*A crash could also be caused by having '''apic support''' enabled in the kernel config. Try disabling it (in the "Processor type and features" section).
:*On machines with Savage chipsets, the '''savagefb framebuffer driver''' might crash the machine on resume. Make sure it is disabled in your kernel config and use the standard vesafb driver instead.
:*Sonoma chipset based laptops ({{R52}}, {{T43}}, {{T43p}}, {{X41}}, {{X41T}}) utilize the '''SATA layer for disk access''' and SATA does not have power-management support yet. Suspend to RAM crashes these machines on resume. See the [[Problems with SATA and Linux#Hang on resume from suspend to RAM|relevant section]] on the [[Problems with SATA and Linux]] page.
:*When system resumes it hangs right after restarting tasks. This may be fixed by passing ec_intr=0 on kernel cmdline.
;Shutdown on resume:
:If your system immediately begins to shut down right after resume, make sure you don't have acpid running with the power button tied to shutdown. The system is simply sensing the power button event and shutting down. This issue has been reported as a bug against the kernel ACPI subsystem, refer to [http://bugzilla.kernel.org/show_bug.cgi?id=6612 kernel.org bugzilla bug #6612].

;Immediate suspend on resume:
:When running GNOME, sometimes gnome-power-manager will put the system back into suspend immediately after resuming. This is caused by a known bug in HAL that causes some ACPI events to be reported incorrectly after a suspend-to-ram. A simple workaround can be found [http://live.gnome.org/GnomePowerManager/Faq#head-b8b1280115b0a51c2cc27b13a57121130ebf36cb here].
:Note that suspend being triggered by unrelated ACPI events such as disconnecting the AC adapter may also be fixed by the above method.

Problem with display remaining black after resume

2006-06-18T19:56:40Z

Uberpenguin: /* Solution for ThinkPads with ATI graphic chips (or Intel 915GM) */ there is no need to kill off HAL; there's a nicer workaround that doesn't cause gnome-power-manager to die

There has been a problem encountered where the display stays black on resuming from suspend.

The symptom might have you think first that your system hang up, but you will realize that your ThinkPad works and you can even reset it via {{key|Ctrl}}{{key|Alt}}{{key|Del}}.

==Affected Models==
*ThinkPad {{T41p}}, {{T42}}, {{T42p}}, {{T43}}, {{T43p}}
*Thinkpad {{T23}}
*ThinkPad {{X21}}, {{X30}}, {{X31}}, {{X40}}, {{X41}}
*ThinkPad {{R31}}, {{R50e}}{{footnote|1}}, {{R50p}}, {{R51}} (with BIOS 1.11), {{R52}}
*ThinkPad {{A30p}}
*ThinkPad {{390X}} (doesn't wake up; LCD backlight on, harddrive light remains on)
*ThinkPad {{Z60t}}, {{Z60m}}

==Affected Operating Systems==
*Linux (it's a kernel issue)

==Solutions==
===Solution for ThinkPads with 1400x1050 internal LCD and Intel 915GM ===
see [[1400x1050 on Intel 915GM]].
===Solution for ThinkPads with ATI graphic chips (or Intel 915GM)===
One solution may be to provide the {{bootparm|acpi_sleep|s3_bios}} kernel parameter in your kernel parameter line.

For grub this would look like this:

title Linux, kernel 2.6.11-1-686
root (hd0,0)
kernel /boot/vmlinuz-2.6.11-1-686 root=/dev/hda1 ro acpi_sleep=s3_bios
initrd /boot/initrd.img-2.6.11-1-686
savedefault
boot

For lilo it would look like this:

image=/boot/vmlinuz
append="acpi_sleep=s3_bios"

The actual process of going to sleep is then managed through a sleep script; as a start, see the {{path|sleep.sh}} script in the Extreme Graphics 2 section below, but note the following comments:

In [[:Category:OpenSUSE|OpenSUSE]] 10.1 (at least on a T43p), it's necessary to override the default options for s2ram if you're using the newer ATI driver. This can be done putting {{bootparm|SUSPEND2RAM_FORCE|"yes"}} and {{bootparm|SUSPEND2RAM_ACPI_SLEEP|"3"}} in {{path|/etc/powersave/sleep}}.

In {{Ubuntu}} or {{Kubuntu}}, it may be necessary to modify {{path|/etc/default/acpi-support}}. In that file, make sure that {{path|ACPI_SLEEP}} is uncommented and set to true. With ATI chips, also make sure that {{path|SAVE_VBE_STATE}} is uncommented and set to true; with Intel chips, on the other hand, ensure that nothing is done with respect to VBE--no reposts, no state saves.

In {{Fedora}}, it may be necessary with the Intel chips to edit the {{path|resume_video()}} function in {{path|/etc/pm/functions-intel}} to comment out the VBE post and restore. Also, the laptop, after waking up, may go back to sleep immediately or whenever the AC adapter is disconnected. When this happens, it's caused by a bug in the HAL daemon that incorrectly reports certain ACPI events. This is a known problem and a simple workaround is described [http://live.gnome.org/GnomePowerManager/Faq#head-b8b1280115b0a51c2cc27b13a57121130ebf36cb here].

{{NOTE|It is possible this method will not work if the laptop is docked.}}

Another solution is to use vbetool. If you are using {{Debian}} with the hibernate package, uncomment "EnableVbetool yes" in {{path|/etc/hibernate/hibernate.conf}} (or {{path|/etc/hibernate/ram.conf}}).

===Solution for ThinkPads with Intel Extreme Graphics 2===
{{NOTE|
On [[:Category:X40|X40]]s/[[:Category:X41|X41]]s - even with Intel Extreme Graphics - and for [[:Category:R52|R52]]s with Intel Graphics Media Accelerator 900 the [[Problem with display remaining black after resume#Solution for ThinkPads with ATI graphic chips|solution for ATI graphics chips]] above is reported to work. In this case, make sure no changes to VBE are made, especially no state saves and no reposts.}}

The following solution should work on 865G, 865GV, 855GM, 855GME, 852GME chipsets.
*First of all, '''do not''' use the {{bootparm|acpi_sleep|s3_bios}} kernel parameter.
*Second, completely remove framebuffer support from your kernel. If it's built as modules, it is important that they do not get loaded at all.
*Before suspending, change to a console and safe the video state with {{cmdroot|cat /proc/bus/pci/00/02.0 > /tmp/video_state}}.
*On resume, restore the video state with {{cmdroot|cat /tmp/video_state > /proc/bus/pci/00/02.0}} and change back to X.
*For a R50e the only thing needed to make suspend to ram work in Ubuntu 6.06 is adding
Option "VBERestore" "yes"
to the <tt>Device</tt> section in your {{path|/etc/X11/xorg.conf}}, and the example script below.

The following example {{path|/etc/acpi/actions/sleep.sh}} script shows how to integrate the according lines.

#!/bin/bash

# change to console 1
FGCONSOLE=`fgconsole`
chvt 6

# safe video state
cat /proc/bus/pci/00/02.0 > /tmp/video_state

# sync filesystem
sync

# sync hardware clock with system time
hwclock --systohc

# go to sleep
echo -n 3 > /proc/acpi/sleep

# waking up
# restore system clock
hwclock --hctosys

# restore video state
cat /tmp/video_state > /proc/bus/pci/00/02.0

# change back to X
chvt $FGCONSOLE

# clean up behind us
rm /tmp/video_state

===Solution for ThinkPads with Intel I830 Chipset===
The following solution worked for me on an X30 with I830M chipset with kernel >= 2.6.16.
*this works with vesafb and also with intelfb frambuffer support.
The following example {{path|/etc/acpi/actions/sleep.sh}} script shows how to integrate the according lines.

#!/bin/bash

FGCONSOLE=`fgconsole`
chvt 8
sync
hwclock --systohc

echo -n "mem" > /sys/power/state

hwclock --hctosys
vbetool post

if [ "$FGCONSOLE" -ge "7" ] ; then
chvt $FGCONSOLE
else
chvt 7
chvt $FGCONSOLE
fi

{{footnotes|
#If you have this problem with R50e and the above solution doesn't work, try switching to console first. An example sleep script can be found [[How to configure acpid|here]].
}}

ThinkWiki - User contributions [en]

Problems with ACPI suspend-to-ram

Problem with display remaining black after resume