ThinkWiki - User contributions [en]

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-10-26T16:34:39Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==

Note: You can use Ubuntu 7.10 instead, in which the ATI issue is apparently fixed

* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

Some cheaper T60p come with an Intel 3945 wireless card for 802.11a/b/g. This is supported out of the box in Ubuntu 7.10 (Gutsy Gibbon) with no additional downloads. The following applies to more expensive models, for which wireless does not work out of the box.

* '''Wireless'''

Some t60p (8744C9U) use an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work---not perfectly---with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5418''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' '''Kinda successful madwifi install''' prequel (for a fully functional wifi card install,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect---my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network. Pretty good nonetheles
given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: '''Back to the Windows driver''' and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

Sometimes, the wireless does not connect right away. Toggling the hotkey usually takes care of the problem.

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-29T13:38:00Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work---not perfectly---with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' '''Kinda successful madwifi install''' prequel (for a fully functional wifi card install,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect---my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network. Pretty good nonetheles
given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: '''Back to the Windows driver''' and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-29T13:37:13Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work---not perfectly---with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' '''Kinda successful madwifi install''' prequel (if you are lacking in time or curiosity,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect---my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network. Pretty good nonetheles
given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: '''Back to the Windows driver''' and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-29T13:36:39Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work---not perfectly---with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Kinda successful madwifi install prequel (if you are lacking in time or curiosity,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect---my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network. Pretty good nonetheles
given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: '''Back to the Windows driver''' and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-29T13:35:57Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work---not perfectly---with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Kinda successful madwifi install prequel (if you are lacking in time or curiosity,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect---my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network. Pretty good nonetheles
given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-28T18:55:37Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work---not perfectly---with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Kinda successful madwifi install prequel (if you are lacking in time or curiosity,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-28T18:54:56Z

Nicolasrobidoux: /* Installing Unbuntu Feisty Fawn */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY which has not been carefully checked.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Kinda successful madwifi install prequel (if you are lacking in time or curiosity,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:09:54Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Kinda successful madwifi install prequel (if you are lacking in time or curiosity,
'''go straight to Step 1).'''

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:09:28Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Kinda successful madwifi install prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:08:46Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Here are detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:08:12Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Detailed instructions on how to install the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:07:10Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a.
'''Atheros Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a.
'''Pciid 168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:06:27Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the '''Thinkpad 11abgn''' a.k.a. ```Atheros AR5416''' a.k.a. '''Atheros
Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a. '''Pciid
168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:05:49Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the '''Thinkpad 11abgn''' a.k.a. '''Atheros AR5416''' a.k.a. '''Atheros
Communications, Inc. Unknown device 0024 (rev 01)''' a.k.a. '''Pciid
168C:0024 (rev 01)''' wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:05:01Z

Nicolasrobidoux: /* Installing Unbuntu Feisty Fawn */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:04:35Z

Nicolasrobidoux: /* T60p hardware setup */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p Hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

'''Step 0)''' Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

'''Step 1)''' We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

'''Step 2)''' Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

'''Step 3)''' Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

'''Step 4)''' (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

'''Step 5)''' Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

'''Step 6)''' Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

'''Step 7)''' In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

'''Step 8)''' Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:02:41Z

Nicolasrobidoux: /* T60p hardware setups */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p Hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setup =

* '''Wireless:'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

'''Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.'''

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:02:07Z

Nicolasrobidoux: /* T60p hardware setups */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p Hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setups =

* '''Wireless:'''

The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

'''Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.'''

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:01:24Z

Nicolasrobidoux: /* T60p Hardware setups */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p Hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p hardware setups =

* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-27T18:01:01Z

Nicolasrobidoux: /* Installing Unbuntu Feisty Fawn */

= Installing Unbuntu Feisty Fawn =

'''Except for the T60p Hardware setup section, THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p Hardware setups =

* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:47:32Z

Nicolasrobidoux: /* T60p Hardware setups */

= Installing Unbuntu Feisty Fawn =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p Hardware setups =

* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2 Duo MacBooks.

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:47:00Z

Nicolasrobidoux: /* T60p Hardware setups */

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:44:23Z

Nicolasrobidoux: /* T60p Hardware setups */

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:40:00Z

Nicolasrobidoux: /* T60p Hardware setups */

= Installing Unbuntu Feisty Fawn =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p Hardware setups =

* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in early releases of Feisty Fawn will *NOT* work.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2
Duo MacBooks.

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting close to my wireless hub).

The network also disconnects at random times, although it almost always immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver and wrapper.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine (or use cabextract).

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey. The wireless also recovers
quickly from suspend to RAM (alternative: turn off the wireless prior
to closing the lid, and restart it).

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:33:26Z

Nicolasrobidoux: /* T60p Hardware setups */

= Installing Unbuntu Feisty Fawn =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p Hardware setups =

* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in Feisty Fawn will *NOT* work. Either get a newer release (when available), or build from SVN.

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2
Duo MacBooks (thank you, macbook users).

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting next to my old Linksys WRT54GS
v.2 with current firmware).

The network also disconnects at random times, although it immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine.

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey.

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:27:46Z

Nicolasrobidoux: /* T60p Hardware setups */

= Installing Unbuntu Feisty Fawn =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p Hardware setups =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''
* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in Feisty Fawn will *NOT* work. Either get a newer release (when available), or build from SVN.

The following is not from memory and has been checked carefully:

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2
Duo MacBooks (thank you, macbook users).

Step 0) Madwifi prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting next to my old Linksys WRT54GS
v.2 with current firmware).

The network also disconnects at random times, although it immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine.

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey.

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.

Installing Ubuntu 7.04 Feisty Fawn on a ThinkPad T60p

2007-08-26T21:25:11Z

Nicolasrobidoux: /* T60p Hardware setups */

= Installing Unbuntu Feisty Fawn =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''

== The long, but easy way ==
* Install earlier version of Ubuntu (6.06/6.10) and dist-upgrade. If you start from 6.06 you will have to upgrade to 6.10, and then upgrade to 7.04.

== The fast way ==
* Be sure to have a *wired* network connection ready (wifi will not work yet)
* Download a ubuntu 7.04 feisty fawn image from ubuntu.com
* Boot from the CD, and wait ... the installation will break down when attempting to start the graphical part of the installation (X).
The problem is, that the ATI driver required for X is not working. Luckily it is already in the ubuntu repos, so we just install it temporarily (in RAM), so we can get on with the installation. When you have a console prompt (in Kubuntu, you will need to remove the "splash" boot option to get the prompt), do a:
apt-get update
apt-get install xorg-driver-fglrx fglrx-control
depmod -a
then restart X with:
/etc/init.d/gdm restart
for Kubuntu, use:
/etc/init.d/kdm restart
With any luck X should launch, so you can click on the desktop icon and continue the installation.

If X doesn't launch, try changing the Driver in /etc/X11/xorg.conf from "vesa" to "fglrx", then restart X.

= T60p Hardware setups =

'''THIS IS A DRAFT WRITTEN FROM MEMORY AND HAVE NOT BEEN VERIFIED YET.'''
* The t60p uses an Atheros network device with this signature "Atheros Communications, Inc. Unknown device 0024 (rev 01)". It will work with any [[Madwifi]] driver version later than subversion revision '''2360'''. This means that the madwifi included in Feisty Fawn will *NOT* work. Either get a newer release (when available), or build from SVN.

Here are some details:

Installing the Thinkpad 11abgn a.k.a. Atheros AR5416 a.k.a. Atheros
Communications, Inc. Unknown device 0024 (rev 01) a.k.a. Pciid
168C:0024 (rev 01) wireless card under Ubuntu Feisty on a Lenovo
Thinkpad T60p 8744-C9U.

The following instructions are most likely applicable to many
Thinkpads which use a "Thinkpad" wireless card, as well as many Core 2
Duo MacBooks (thank you, macbook users).

Step 0) Prequel (if you are lacking in time or curiosity, go straight
to Step 1).

The instructions found at

http://ubuntu-tutorials.com/2007/08/02/how-to-setup-wireless-on-a-macbook-using-madwifi-710-gutsy

modified so that you

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

instead of wget the madwifi which is indicated, make everything work
fairly well except that the wireless on/off hotkey does not affect the
wireless (only bluetooth) and the wireless light does not turn on.
Not a big deal, although annoying.

For reference, here is my version of these painless---but somewhat
lacking as far as the Thinkpad goes---instructions:

sudo aptitude install build-essential

wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gz

tar -zxvf madwifi-ng-current.tar.gz

cd madwifi-ng-current

make

sudo make install (answer "r" when asked about previous modules)

Unfortunately the card only achieves between 12 Mb/s (after suspend to
RAM, resuming after wired connection or turning it off) and 36 Mb/s
(at boot, and then only if I am sitting next to my old Linksys WRT54GS
v.2 with current firmware).

The network also disconnects at random times, although it immediately
reconnects... at a lower speed.

This is not the performance I would expect (my old Thinkpad R51
running Gentoo reliably goes 54 Mb/s on the same network), although I
should not be ovverly surprised, given that the good madwifi folk are
not getting all the help they could from Atheros.

In other words: Back to the Windows driver.

Step 1) We will adapt

http://www.edsupport.cc/mguhlin/archives/cat_ubuntu.htm

and the INSTALL file which comes with the ndiswrapper tar file, with
some modifications.

Download the latest stable ndiswrapper tar.gz file from

http://ndiswrapper.sourceforge.net/

(As of 08/2007, it is version 1.47. You may be happy with the version
which can be installed by Synaptic: issue ndiswrapper -v in the
command line to find the version.)

Use Archive manager to uncompress and save to your Desktop.

The informative INSTALL file is found ~/Desktop/ndiswrapper*/INSTALL

Step 2) Remove previous installations of ndiswrapper by typing in the
following at the command line (in a terminal):

sudo aptitude remove --purge ndiswrapper-common ndiswrapper-utils

sudo rm -R /etc/ndiswrapper

sudo rm /etc/modprobe.d/ndiswrapper

Step 3) Use Synaptic or

sudo aptitude install build-essential wine

to install build-essential and wine (if you don't have them already).

Step 4) (Re)compile ndiswrapper:

cd ~/Desktop/ndiswrapper*

Read the message returned by the following command, and run it as
often as necessary (for me, once was enough):

sudo make uninstall

Then:

make

sudo make install

Step 5) Download the Lenovo driver compressed file 7iwc28ww.exe from

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-66449

Alternatively: To get the file, type this in your browser

ftp://ftp.software.ibm.com/pc/pccbbs/mobiles/7iwc28ww.exe

The file 7iwc28ww.exe should now appear on your Desktop (unless you've
changed download defaults).

Step 6) Make a folder into which to put the many files which are in
7iwc28ww.exe by typing

mkdir lenovo

on the command line.

Now, open 7iwc28ww.exe by right clicking on it. If Gnome does not know
already to open an .exe with wine, tell it to use a custom
application, and make it wine.

An InstallShield Wizard will pop up. Push buttons in it:

next -> accept -> next -> change (the save location) to Desktop/lenovo
-> next -> finish

Step 7) In the command line:

cd ~/Desktop/lenovo/WINXP_2K/

(The following step may be unnecessary.)

cp ../*.BIN .

sudo ndiswrapper -i NET5416.INF

A bunch of "forcing parameter MapRegisters from 256 to 64" messages
will appear. Not to worry (although some people change these back in
conf files, I did not bother).

Check whether the install went through:

In the command line:

ndiswrapper -l

You should get: "net5416 : driver installed device (168C:0024) present".

sudo modprobe ndiswrapper

(In case you have a firegl ATI graphics card: this last modprobe does
not break a good install.)

Step 8) Now, the wireless card works at top speed and reliably, and
the wireless hotkey and the wireless light work, and suspend to RAM
does not mess things up.

You may, however, find that the wireless does not kick in at boot,
this may be that the /etc/modules, which lists additional modules to
load at boots, specifies another wireless card driver.

This can be fixed as follows:

Edit the /etc/modules file as root, that is,

sudo gedit /etc/modules

Comment out with a "#" the entry(ies) which you suspect have to do
with wireless (in my case, it was ath_pci). For good measure, add
ndiswrapper.

Now, if you want to boot into wired, hotkey the wireless off, and if
you want to boot into wireless, hotkey the wireless on. You can also
switch from one to the other with the hotkey.

* The fans are too noisy and can be throttled down by using the [[ACPI fan control script]]. Increase the min and max to 70, 100 on the GPU. This will lower the fan speed to <3000 for normal usage (XGL/Compiz fusion setup).
* You should install a 'generic' kernel i favor of the i386 to gain better performance of the dual core, and better suspend.
* Compiz fusion (previously compiz and beryl) will run smoothly of this hardware, using ATI's fglrx and XGL. Use trevinos repository [http://ubuntuforums.org/showthread.php?t=481314 http://ubuntuforums.org/showthread.php?t=481314]

NOTE July 2007 I tried the instructions for Compiz and to date was unable to get it working on the T60p, if anyone has some better instructions please update them here.

* You can tweak the 'fn' keys to work well too.