Difference between revisions of "Talk:How to control fan speed"

From ThinkWiki
Jump to: navigation, search
(Adding Z61m Fan speeds in Discussionarea. Please add to the List.)
(request for explanation, `the above` in 'Supported models' section)
 
(3 intermediate revisions by 3 users not shown)
Line 1: Line 1:
Z61m is the same like Z60.
+
== Please explain ==
 +
 
 +
What exactly is meant with `the above` in the "Supported models"-section ?
 +
 
 +
''The above was successfully tested on the following models:''
 +
 
 +
Because I haven't tried everything that is above that section,
 +
but am probably going to add my fan-specs anyway...
 +
 
 +
 
 +
== Z61m is the same like Z60. ==
  
 
The kernel 2.6.18 ibm_acpi 1.12a does not allow speed command. but with direct ecdump it works.
 
The kernel 2.6.18 ibm_acpi 1.12a does not allow speed command. but with direct ecdump it works.
Line 26: Line 36:
  
 
(perhaps this table helps a little bit.)
 
(perhaps this table helps a little bit.)
 +
 +
== disengaged mode reset automatically ==
 +
 +
For some reason, whenever I issue command echo level disengaged > /proc/acpi/ibm/fan, the mode is reset to auto ("by hardware") in few seconds.
 +
 +
Thinkpad T60
 +
Ubuntu Gutsy
 +
 +
root@Thinkbaby-Ubuntu:~# uname -a
 +
Linux Thinkbaby-Ubuntu 2.6.22-14-generic #1 SMP Tue Feb 12 07:42:25 UTC 2008 i686 GNU/Linux
 +
 +
I have also added "options thinkpad_acpi fan_control=1" to /etc/modprobe.d/options.
 +
 +
Any idea?
 +
 +
---
 +
 +
Yes. Take such questions off thinkwiki and into a proper ML, like linux-thinkpad, and I will try to answer them.
 +
 +
--[[User:Hmh|hmh]] 03:52, 13 June 2008 (CEST)
 +
 +
== X61s ==
 +
 +
On my X61s with Ubuntu 7.10 i've got speed about 5950 in disengaged mode

Latest revision as of 10:11, 13 March 2010

Please explain

What exactly is meant with `the above` in the "Supported models"-section ?

The above was successfully tested on the following models:

Because I haven't tried everything that is above that section, but am probably going to add my fan-specs anyway...


Z61m is the same like Z60.

The kernel 2.6.18 ibm_acpi 1.12a does not allow speed command. but with direct ecdump it works. the displayed fan speed changes. (But i dont notice any noise difference)

On Z61m and Kenrel and unpatched ibm_acpi from 2.6.18: on Start the Fan is disabled :( speed 0. with echo enable > fan the fan goes to maximum rpm of 2400. (Temperatur goes above 78°C .. Bad)

On Full CPU Duty: Mode RPM 0 0 (fast switch) 1 2257 (slow switch, 5-10s) 2 2257 3 2664 (fast switch) 4 2699-2719 5 2800 6 3400 7 3284 (100%load cpu temp 68°C) 8-F same as 7 0x8F 2600 !! 0xFF speed is not chaning anymore ? (not measurement ?) 0xCF 4200 (very slow chaning.. 30s for spin up)

(perhaps this table helps a little bit.)

disengaged mode reset automatically

For some reason, whenever I issue command echo level disengaged > /proc/acpi/ibm/fan, the mode is reset to auto ("by hardware") in few seconds.

Thinkpad T60 Ubuntu Gutsy

root@Thinkbaby-Ubuntu:~# uname -a Linux Thinkbaby-Ubuntu 2.6.22-14-generic #1 SMP Tue Feb 12 07:42:25 UTC 2008 i686 GNU/Linux

I have also added "options thinkpad_acpi fan_control=1" to /etc/modprobe.d/options.

Any idea?

---

Yes. Take such questions off thinkwiki and into a proper ML, like linux-thinkpad, and I will try to answer them.

--hmh 03:52, 13 June 2008 (CEST)

X61s

On my X61s with Ubuntu 7.10 i've got speed about 5950 in disengaged mode