Search results

Jump to: navigation, search
  • #It is working with lilo boot loader, however it failed with syslinux.
    54 KB (6,098 words) - 02:34, 7 March 2020
  • ...ure out how, but it would be nice to have a little grub counterpart to the lilo-ness. Thanks, anyone who decides to take up my challenge :)
    1 KB (197 words) - 07:45, 24 December 2005
  • ...partitions) and when the time comes to install GRUB (you do prefer GRUB to LILO, don’t you?), make sure you install it into the boot sector of the b
    21 KB (3,356 words) - 21:05, 20 December 2019
  • ...r both. Yes, it happened to me... :-( Interrupting the boot process at the lilo boot menu, and then inserting the ipw2915abg card worked as a charm to circ
    10 KB (1,797 words) - 13:58, 3 June 2014
  • * Linux fails to boot: On boot, Grub displays ''Error 17''; Lilo shows ''L 99 99 99 99 ...''
    12 KB (2,012 words) - 23:37, 27 January 2014
  • ...rted by VESA for T60 is 1280x1024. You can set that for console in grub or lilo by adding vga=794 option.
    11 KB (1,734 words) - 14:55, 22 January 2021
  • ...he solution is to include 'vga-791' or to remove 'splash' from the grub or lilo command line. You don't need to do both. (It's been a few days, so I don't
    11 KB (1,746 words) - 14:49, 22 January 2021
  • {{path|/etc/lilo.conf}} should look like LILO version 22.5.9, as installed with Slackware 10.1, complains about the <tt>l
    21 KB (3,442 words) - 16:49, 26 October 2006
  • *Resolved by installing LILO instead. LILO installed fine, but didn't recognise the two Windows partitions and just bo Replaced LILO (which didn't see either Windows partition) with GRUB with the following co
    3 KB (541 words) - 23:27, 11 December 2006
  • ...tra 5GB (do at your own risk!) Make sure you have a basic understanding of lilo and how to recompile a kernel. Get the Slackware installation set (disks 1 ...r new .config) to your {{path|/boot}} directory, and add it to {{path|/etc/lilo.conf}}
    9 KB (1,548 words) - 02:20, 19 June 2010
  • ...boots the installed system from the hard disk, just like the old days with LILO and a boot floppy. Once the installation and you're logged in, start YaST2
    51 KB (7,507 words) - 11:46, 8 January 2008
  • ...boots the installed system from the hard disk, just like the old days with LILO and a boot floppy. Once the installation and you're logged in, start YaST2
    8 KB (1,267 words) - 06:24, 28 September 2007
  • # vi /etc/lilo.conf # lilo # see [[#Lilo Options|'''lilo options''']]
    11 KB (1,728 words) - 19:14, 26 June 2007
  • First, did you boot into "Safe Graphics Mode" from LILO or Grub, or from a graphical login screen? My installation hangs right bef
    4 KB (773 words) - 20:47, 9 September 2007
  • * Make system bootable, choosing '''/dev/hda''' if you wish to have LILO take over booting
    6 KB (915 words) - 18:17, 8 December 2007
  • *Skip LILO (unless you like pain)
    75 KB (12,480 words) - 17:49, 5 August 2011
  • ...uide on ThinkWiki), then downloaded the netboot files for Dapper, and used Lilo to load them and start the installer. Edit /etc/lilo.conf to include these new files. My new section looks like this:
    10 KB (1,785 words) - 15:49, 24 December 2007
  • ...tition and asked for a mount point for fstab, as well as recognizing it in lilo and adding a boot entry for it. Once the installation was completed, a simple reboot brought up the lilo boot menu, and I chose my new Slackware installation.
    4 KB (599 words) - 09:19, 24 April 2009
  • *Install LILO to the Linux partition. This leaves the MBR untouched and retains the abili ...XX''' with one of the above numbers in '''/etc/lilo.conf''' then re-run '''lilo'''.
    7 KB (807 words) - 17:22, 20 June 2010
  • ...e your kernel compiled and install, reboot and choose it from your grub or lilo menu. Hopefully it boots Ok, and you can open a command line and
    9 KB (1,351 words) - 09:34, 14 October 2008

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)