Difference between revisions of "Installing Ubuntu 6.10 on a ThinkPad T43"

From ThinkWiki
Jump to: navigation, search
Line 1: Line 1:
Installation Log of {{Ubuntu}} (Kubuntu) 6.10 on a {{T43}}  
Installation Log of Kubuntu 6.10 on a {{T43}}  
Disclaimer - Most of this article stolen from [[Installing_Ubuntu_6.06_on_a_ThinkPad_T43]]. WORK IN PROGRESS
Disclaimer - Most of this article stolen from [[Installing_Ubuntu_6.06_on_a_ThinkPad_T43]]. WORK IN PROGRESS
Line 280: Line 280:
Hope this helped somehow :-)
Hope this helped somehow :-)
[[Category: Kubuntu 6.10]] [[Category: Ubuntu 6.10]]

Revision as of 23:57, 26 August 2007

Installation Log of Kubuntu 6.10 on a T43

Disclaimer - Most of this article stolen from Installing_Ubuntu_6.06_on_a_ThinkPad_T43. WORK IN PROGRESS


Worked right out of the box

  • 1400*1050 resolution
  • Battery Management
  • Ultra Nav (Trackpoint and synaptic touchpad) 3rd button scroll did not work
  • WLAN (Atheros, IBM 11a/b/g Wireless LAN Mini PCI Adapter II)
  • Hibernate and Standby
  • Audio Keys
  • ThinkLight

Was easy or required some work

  • middle key of Ultra Nav (Trackpoint)
  • ATI 3D Acceleration (Mobility Radeon X300)

Still TODO

  • Beryl


  • Bluetooth (light indicates working)
  • Modem
  • IrDA


Recovery copy of data

Before installing a new OS you should create a security copy of your old system. As the IBM Rescue and Recovery tool quit with an error message I used the Ubuntu live CD, mounted and cd'ed into my external hard drive and ran the following command:

$ cmduser|sudo dd if=/dev/sda1 | gzip | dd of=./sda1.img

where /dev/sda1 is the device with my windows partition and sda1.img the gzipped security copy. In case of problems one can now restore lost information using

$ sudo dd if=./sda1.img | gzip -d | dd of=/dev/sda1 

After creating the recovery copy we are ready to resize the existing windows partition. This article assumes you want to keep your IBM Rescue and Recovery Partition, shrink in size, but keep your windows partition and create a new partition for Dapper Drake.

Resizing Partitions

I used Partition Magic, but others have done the following...

Probably the best choice is now to boot from the alternate CD (read [1] to know why) and use it to resize the existing NTFS partition. Unfortionately in my case it didn't work. So I booted the Live CD, but gparted and parted refused to resize my Windows, too. If the same happens to you, use the example here to know how to resize it "manually" using ntfsresize and fdisk.

After resizing your windows partition you should reboot window to check everything's in order. It probably will run checkdisk and reboot two times - according to experieces you can read in the web, you should better let windows do that.

Installation of Ubuntu

Now it's the time to install Ubuntu. I used the alternate CD for that because I chose to install grub into the Linux partition and not into the Master Boot Record (read why). The graphical LiveCD installer automatically installs grub to the MBR. If you want to use grub in the MBR read Rescue and Recovery. There is a description of what you have to do in order to still be able to use the IBM R'n'R partition.

  • remember that you're installing GRUB to an sda mount, not an hda mount like the GRUB installer will prompt you for what you should enter after you tell GRUB not to install in the MBR will be something like this:

After the installation is finshed it will reboot your system. Now windows should start. In my case it didn't, but playing around, booting into the R'n'R partition, starting PC Doctor and doing some Diagnostics (no changes) somehow and surprisingly made windows boot again.

To boot you freshly installed Linux you have to reboot the LiveCD one last time. Use

$ sudo dd if=/dev/sda5 of=ubuntu.img bs=512 count=1

to copy the first block of grub into an image file and use e.g. an usb flash drive to transfer it to your newly booted windows. Copy paste the image to C:\ and add the following line to your C:\boot.ini:

C:\ubuntu.img="Ubuntu Dapper Drake"

At the next restart the windows boot manager should now welcome you with the choice to boot windows or ubuntu. Choose ubuntu to (finally ;-) boot your newly installed linux for the first time.


3D Acceleration and Xgl/Compiz

If you have an ATI Radeon X300, use this explanation to make your hardware 3d acceleration work.

To test if it works type

$ glxinfo | grep rendering

The answer should be: "direct rendering: Yes". If it says "No", you don't have 3D acceleration.

If you have another card you might find a good explanation here.

3D Acceleration using open-source radeon driver and AIGLX/Beryl

From my experience it was better to use "radeon" driver, the open source one, on top of "drm" driver, also part of the kernel, instead of fglrx. I get direct rendering and similar performance---maybe fglrx driver gives 50-100 more fps. The most annoying thing about fglrx driver is that it can cause hard locks every now and then and your suspend doesn't work properly...believe me I tried the ones that the Thinkwiki says supposed to work.

$ glxinfo | grep rendering
direct rendering: Yes
OpenGL renderer string: Mesa DRI R300 20060815 TCL

Use the directions in the previous section to install fglrx driver, library. (I just installed them from shell rather than making them into packages, I found the uninstall script in /usr/share/fglrx to work properly). FYI, I used the version 8.26.18-x86.

If you don't get rendering use LIBGL_DEBUG=verbose glxinfo to diagnose the problem. The most common problem is that xorg looks for DRI library files in /usr/X11R6/lib/dri, which didn't exist for me. A simple way to solve this is creating a symlink to where those files are located (/usr/lib/dri/):

$ cd /usr/X11R6/lib/
$ ln -s /usr/lib/dri/ .

Open your /etc/modules file and add these lines and comment 'fglrx' if there is any:


Also, from my experience, it was better to use AIGLX than Xgl and Beryl instead of Compiz in terms of performance and integration---things like suspend and hibernate. And you can use nice start/shutdown scripts to disable beryl-manager since it can cause hang when you resume from suspension. For more information about suspend/resume scripts, here. For more information about installing aiglx and beryl, see here).

ATI X300 is pretty pitiful though...I get around ~570 average FPS when running AIGLX/beryl

$ glxgears
2850 frames in 5.0 seconds = 569.997 FPS
2925 frames in 5.0 seconds = 584.925 FPS
2904 frames in 5.0 seconds = 580.741 FPS
2923 frames in 5.0 seconds = 584.524 FPS...

With metacity (default Gnome window manager) I get around slightly over 1000 FPS

$ glxgears
5073 frames in 5.0 seconds = 1014.423 FPS
5073 frames in 5.0 seconds = 1014.531 FPS
5252 frames in 5.0 seconds = 1049.326 FPS
5803 frames in 5.0 seconds = 1160.502 FPS...

I added the following options under ati Device section of /etc/X11/xorg.conf

Option      "EnablePageFlip" "True"
Option      "ColorTiling" "True"

Then after that the performance boosted by quite a bit:

7026 frames in 5.0 seconds = 1405.147 FPS
7058 frames in 5.0 seconds = 1411.493 FPS
7062 frames in 5.0 seconds = 1412.393 FPS...

Active Protection System

See end of this chapter if you have ubuntu edgy eft.

The T43 has a great system to protect your hard disk, the Active Protection System APS. How to protect the harddisk through APS describes how you can use it.

Only follow these instructions if you know what you are doing!

If you didn't until now you will have to install make, libc, gcc, ... Best is you use

$ sudo apt-get install build-essential

Determine your kernel version using

$ uname -a

You should see somthing like

Linux ibm 2.6.15-26-386 #1 PREEMPT Thu Aug 3 02:52:00 UTC 2006 i686 GNU/Linux

Install the kernel sources "linux-source" e.g. using Synaptic. Download the right kernel patch from HDAPS#Applications according to your kernel version and system (I chose "sata/ide disk protection patch for 2.6.15") adapt following steps to your needs:

$ cd /usr/src/
$ sudo su
# bunzip2 linux-source-2.6.15.tar.bz2
# tar -xf linux-source-2.6.15.tar
# cd linux-source-2.6.15
# patch -p1 -l < /home/silvan/hdaps_protect.20060118.patch

You should see several lines with the word "suceeded". If you see many "failed" instead you probably chose the wrong patch for your kernel. You can use the --dry-run option to try it out first. If you get errors in the following steps you should better stop unless you know what you are doing.

# make clean
# make oldconfig # use old config, ask for new items, only
# make clean
# make           # takes quite a long time, several minutes
# make modules
# make modules_install

Afterwards use the debian sources mentioned in How to protect the harddisk through APS to install the user space deamon hdapsd and the gnome applet gnome-hdaps-applet, e.g. using Synaptic.

If this worked for you, you can find some nice applications at HDAPS#Applications which make use of the APS.

Help needed
For me unfortunately it didn't work as making the patched kernel failed. Please update ths section if you have different experiences and a better, more detailed working explanation.

After I updated to edgy eft hdaps works without further work: edgy comes with hdaps built in. You can check if it is working by installing hdaps-utils
# sudo apt-get install hdaps-utils

and calling

# hdaps-gl

for a nice 3D show. If it is not, load the kernel module using

# sudo modprobe hdaps

and it should work. But if you want to use hdaps for disk protection, you have to recompile your kernel in edgy, too. Follow this post for an howto:

Howto for edgy

Track Point Middle Key Scrolling

In my case the track point worked out of the box, but the middle mouse button for scrolling did not. How to configure the TrackPoint explains how to solve this. The steps you need to follow are in section "Using the X server (kernel 2.6.11+)". However you don't need to follow the steps in "EmulateWheelTimeout temporarily broken (-> fix for Ubuntu Dapper)" as this is fixed already if you have all your packages up-to-date.

Follow the instructions in the sections "Configure firefox for using trackpoint horizontal scrolling" and "Configure Opera for using trackpoint horizontal scrolling" as well, if you are using one of the two browsers.

Fingerprint Reader

Needs editing

Look at How to enable the fingerprint reader if you want to use your fingerprint reader.

An alternative way can be found at Installing Ubuntu 6.06 on a ThinkPad T43#Fingerprint_Reader.

Spezial keys

If the following standard settings are not enough for you, you'll find more info here: How to get special keys to work

Access IBM to start application

The Access IBM works out of the box. Just go to your shortcut configuration dialog and choose what actionyou want to connect with pressing this button, e.g. opening your home folder/terminal, switching o fullscreen, opening help...

CAPS to substitute Win/Super

For using your CAPS key as a replacement for the lacking Win/Super key, add following to your ~/.Xmodmap

! No Caps Lock
clear lock
! Caps Lock as Win key
add mod4 = Caps_Lock

To avoid restarting X type $ xmodmap ~/.Xmodmap

Forward/Backward in browsers


For using the Forward/Backward Keys in your browser add also these lines to your ~/.Xmodmap as at least Firefox gets confused with their original setting as XF86Back/XF86Forward.

! back and forward browser keys
keycode 234 = F19
keycode 233 = F20

For Firefox add these lines to your /usr/share/firefox/chrome/browser/content/browser/browser.xul

<key id="goBackKb3" keycode="VK_F19" command="Browser:Back" />
<key id="goForwardKb3" keycode="VK_F20" command="Browser:Forward" />

directly after these lines:

<key id="goBackKb"  keycode="VK_LEFT" command="Browser:Back" modifiers="alt"/>
<key id="goForwardKb"  keycode="VK_RIGHT" command="Browser:Forward" modifiers="alt"/>

For Opera add these pairs in Tool->Preferences->Advanced->Shortcuts->Keyboard setup->Edit->Browser Window->New

  • If you did the Firefox Xmodmap entry: F20-Forward, F19-Back
  • If you didn't add the lines: XF86Forward-Forward, XF86Back-Back

In Konqueror it's working out of the box. But if you did the Xmodmap settings you have to adjust Konqueror, too. Just go to Settings->Configure Shortcuts, look for Back and Forward and set the alternative shortcut in the custom dialog by pressing the respective key. If you are using KDE you'll be probable prefering to do that in the Configuration Center to make these changes visible to all KDE Apps.


Needs editing

Find information here: How to make use of IrDA

VGA out

Needs editing

I didn't try it, but it looks easy: How to enable VGA out


External Sources

Hope this helped somehow :-) tec