Difference between revisions of "Installing openSUSE 10.2 on a ThinkPad X60"
McCoy-Tyner (Talk | contribs) (→Integrating an (old) SIEMENS IGATE 11M PCMCIA-wlan card) |
McCoy-Tyner (Talk | contribs) (→Integrating an (old) SIEMENS IGATE 11M PCMCIA-wlan card) |
||
Line 747: | Line 747: | ||
==== Integrating an (old) SIEMENS IGATE 11M PCMCIA-wlan card ==== | ==== Integrating an (old) SIEMENS IGATE 11M PCMCIA-wlan card ==== | ||
− | I own an old IGATE 11M card (still fine for just surfing) I wanted to test. Unfortunately it did not work out of the box, so I describe here what I did to get it going. This issue is an openSUSE 10.2 problem and not specific to | + | I own an old IGATE 11M card (still fine for just surfing) I wanted to test on openSUSE 10.2. Unfortunately it did not work out of the box, so I describe here what I did to get it going. This issue is an openSUSE 10.2 problem and not specific to this wlan card. |
− | This card is based on a prism chipset where | + | This card is based on a prism chipset where a set of linux drivers are available (hostap, orinoco ..). When I used to work with SUSE 9.3 I had had success with the hostap driver so I had planned to use this one here, too. |
− | Yast2 nicely detects the card and allows | + | Yast2 nicely detects the card and allows to configure everything including the appropriate encryption settings (wpa psk in this case). In /etc/sysconfig/hardware/hwcfg-bus-pcmcia-0.0 the hostap driver is entered so initially everything seemed to be alright. |
− | + | However, the card was not working and I found that the orinoco driver had had been loaded - this was astonishing as YaST2 wrote "hostap_cs" int /etc/sysconfig/hardware/hwcfg-bus-pcmcia-0.0. This problem is caused by | |
+ | an error in /etc/modprobe.d/prism2. It causes the orinoco driver to always be loaded what messes up the entire configuration. | ||
− | To | + | In order to avoid this, the file /etc/modprobe.d/prism2 should be modified. It basically contains a list of keys that ought to assign each individual (pcmcia-) card to a specific driver. Unfortunately there is an aliasing phenomenon so there are two matches for this card - one for the orinoco driver, one for the prism2 driver. The orinoco driver does not work with the card, the prism driver is not installed. A pointer to hostap is missing in the file. |
+ | |||
+ | To fix this, the following patch should be applied: | ||
<code> | <code> | ||
--- prism2.original 2006-11-25 16:50:35.000000000 +0100 | --- prism2.original 2006-11-25 16:50:35.000000000 +0100 | ||
Line 778: | Line 781: | ||
</code> | </code> | ||
− | + | This basically removes the reference to the orinoco driver and adds one to the hostap driver. This makes the card work (for me). However, it should be denoted that this may or may not work for other wlan cards that might rely on orinoco / prism2. But probably this is an useful hint where to search for potential issues. | |
== What doesn't work yet == | == What doesn't work yet == |
Revision as of 18:55, 4 June 2007
Contents
- 1 Lenovo ThinkPad X60 (model 1707-CTO / model 1706-8GG)
- 1.1 Hardware Details
- 1.2 Software Details
- 1.3 Installation procedure
- 1.4 What works out of the box
- 1.5 What had to be configured by hand
- 1.5.1 Accessing the nvram - device
- 1.5.2 Automatic power switching for ipw3495
- 1.5.3 Activating FN-F2 and FN-F7
- 1.5.4 Activating the internal modem
- 1.5.5 Activating the fingerprint reader
- 1.5.6 Kernel upgrade to 2.6.21 and solving suspend2ram / suspend2disk stability issues
- 1.5.7 openSUSE specific issues
- 1.5.8 PCMCIA - slot
- 1.6 What doesn't work yet
- 1.7 What I haven't tested yet
- 1.8 lscpi
Lenovo ThinkPad X60 (model 1707-CTO / model 1706-8GG)
Hardware Details
- Intel Core Duo T2400 (1.83GHz, 2MB L2, 667MHz FSB)
- 2GB RAM (2 NonParity DDR2 SDRAM SoDIMM PC2-5300)
- Intel Graphics Media Accelerator 950
- 12.1 inch XGA (1024x768) (Lenovo LTN121XJ-L07)
- 80GB, 5400rpm Serial ATA (Hitachi HTS541080G9SA00) / 100GB Serial ATA on 1706GG (Toshiba MK1034GSX)
- Intel PRO/1000 Gigabit Ethernet
- Intel PRO/Wireless 3945ABG
- Bluetooth
- Firewire
- SD Card Reader
- 56K V.92 Modem
Software Details
- openSUSE 10.2 retail DVD9 iso
Installation procedure
Setup
Since I didn't get a dock or usb CDROM with this machine, I started the installation procedure using a USB Stick. I followed these instructions to set up a boot USB key. This contains GRUB and the loader for the installer. The actual installation media was on an NFS share. To set this up, copy the contents of the CDS/DVD into a directory (or mount the DVD iso image loopback) then share the directory containing CD1 via NFS, is the simplest way. Sharing the DVD as a SMB share works from windows, too.
Using the ultra-bay DVD-drive is straightforward as it is detected at startup and can be booted from. Nothing special about this.
Installation
Press F12 during POST to get the boot selector menu up, choose the USB Key. This boots into GRUB. Press F4 here to set the installation source to NFS or SMB as needed, and enter the server details. For example, with SMB, enter the server name, the name of the share, and the directory where the first CD's contents are, eg 'CD1'. Now the installer is loaded from the share and proceeds as a usual SUSE install. No special steps are required during the install, but read the documentation about preserving or moving the ThinkVantage rescue partition before you commit to the installation.
What works out of the box
Hardware
- Ethernet adaptor
- Intel 3945ABG Wireless ethernet adapter
- GMA950 graphics with 3D acceleration with integral monitor
- Sound playback
- USB
- Firewire
- Bluetooth (with kbluetoothd, gets about 55kB/s with OBEXFTP)
- Trackpoint
- SD card reader
Power management etc
- Suspend to disk (Fn+F12)
- Suspend to RAM (Fn+F4)
- Turn display dark (Fn+F3)
- CPU speed stepping (required BIOS update to 2.05 though)
- LCD Brightness depending on current power scheme, via KPowersave and HAL
Extra keys
- Volume control, keyboard light and screen brightness control
- Lid switch (LCD off when lid closed, resume from suspend to RAM when opened)
- Multimedia keys with KMix and Amarok
- Browser back/forward keys with Konqueror
What had to be configured by hand
- Mouse wheel emulation, set "Emulate Mouse wheel with button 2" in SaX2 mouse settings
- Keyboard dead keys for international characters, set "Right Alt is Compose" in SaX2 keyboard settings, then ralt-shift-2, a => ä
- Sound recording, using KMix or other mixer, set the mic as capture source, turn it up, enable and turn up 'Capture' channel.
- FN-F2 initially does nothing. This requires extra tweaking.
- FN-F7 doesn't work either. Even though ibm-acpi module may be loaded, the video-switch facility does not work.
- The finger print reader, a working driver is existing.
- By default the fan runs all the time. If power management on the ipw3945 is enabled, it only runs about 1/3 of the time. Use 'iwpriv eth1 set_power 7' to enable power management - this comes at the cost of increasing latency when using wireless. See the ipw3495 README for details. A description how to do this automatically can be found below.
Accessing the nvram - device
The default permissions of the nvram device prevent the screen sliders for brightness / volume etc. from being displayed for non root users. To circumvent this problem, a modification of an entry should be made within /etc/udev.d/hooks/50-udev-default.rules:
replace
KERNEL=="nvram", GROUP="kmem", MODE="600"
by
KERNEL=="nvram", GROUP="users", MODE="640"
and every user is able to read from nvram. This ensures that the sliders are displayed when modifying the brightness or the volume.
Automatic power switching for ipw3495
This procedure can be automatized:
Create a script switch_wireless_mode in /usr/lib/powersave/scripts and make it executeable:
#!/bin/bash
###########################################################################
# #
# Powersave Daemon #
# #
# Copyright (C) 2004,2005 SUSE Linux Products GmbH #
# #
# This program is free software; you can redistribute it and/or modify it #
# under the terms of the GNU General Public License as published by the #
# Free Software Foundation; either version 2 of the License, or (at you #
# option) any later version. #
# #
# This program is distributed in the hope that it will be useful, but #
# WITHOUT ANY WARRANTY; without even the implied warranty of #
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU #
# General Public License for more details. #
# #
# You should have received a copy of the GNU General Public License along #
# with this program; if not, write to the Free Software Foundation, Inc., #
# 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA #
# #
###########################################################################
#
# change mode for the wireless network card on X60 lenovo laptop
# currently the interface name needs to be set manually.
#
#
IWPRIV="/usr/sbin/iwpriv"
MODEPARAM="set_power"
POWERSCHEME="6"
BATTERYSCHEME="7"
IF="eth1"
. ${0%/*}/helper_functions
if [ $EVENT_TYPE != ACADAPTER ]; then
DEBUG "switch_wireless_mode only makes sense for acadapter events ;-)" WARN
else
if [ "$1" = "acadapter.online" ]; then
${IWPRIV} ${IF} ${MODEPARAM} ${POWERSCHEME}
fi
if [ "$1" = "acadapter.offline" ]; then
${IWPRIV} ${IF} ${MODEPARAM} ${BATTERYSCHEME}
fi
fi
$SCRIPT_RETURN $EV_ID 0 "switch_wireless_mode finished"
EXIT 0
Finally only two lines have to be modified "on top" of this to make powersaved aware of this script. This ought to happen in /etc/sysconfig/powersave/events:
## Path: System/Powermanagement/Powersave/Events
## Type: string
EVENT_ACADAPTER_ONLINE="reread_cpu_capabilities switch_wireless_mode"
EVENT_ACADAPTER_OFFLINE="reread_cpu_capabilities switch_wireless_mode"
"switch_wireless_mode" should be added to the EVENT_ACADAPTER_ONLINE and EVENT_ACADAPTER_OFFLINE as shown above. Given this, the x60 will switch to low power mode when running on battery and back to high power mode when running on mains automatically.
But be warned: if for any reason the device ID of the wireless adapter should differ from eth1 you will have to edit the file switch_wireless_mode accordingly.
Doing a test
iwpriv eth1 get_power
should make it clear whether everything works as expected, the return values should differ between mains plugged and mains unplugged. This does not work if you suspend your computer when connected to mains, unplug mains and wake it up again. But, I guess that this is not what I would call a characteristic or typical mode of operation.
Activating FN-F2 and FN-F7
Both keys FN-F2 and FN-F7 create acpi events. This can be seen easily by performing a "tail -f /var/log/acpid" and pressing one of those combinations, however, in the initial state of the installation nothing happens afterwards. The following description shows how to make both keys do what you would expect them to.
FN-F2: blocking the screen as soon as FN-F2 is pressed
Firstly I have to point out that this description is referring to kde - users, I am highly convinced that there exists a similar program on gnome for locking the screen but I simply do not know (and did not test). Therefore your mileage may vary.
Locking the screen may be realized by calling: /opt/kde3/bin/kdesktop_lock --forcelock This works from within a kdesktop, however, if you perform this call from a deamon you do not have access to a X11-screen / a kde session. To circumvent this, the call is executed as the user that is currently owning the screen ":0" through sudo. See the patch for "dockhandler" below.
FN-F7: switching video outputs
Every attempt to make
echo "video_switch" > /proc/acpi/ibm/video
work failed. Luckily there is a tool available from Ken Mano at
http://www16.plala.or.jp/mano-a-mano/i810switch.html that can be patched to
make video switching work on x60.
The chip i945 on the x60 should be treated like a i855, so the patch that needs to be applied is:
--- i810switch-0.6.5/i810switch.c.original 2005-06-12 06:36:36.000000000 +0200
+++ i810switch-0.6.5/i810switch.c 2007-02-28 15:05:49.000000000 +0100
@@ -60,6 +60,7 @@
#define I855STR "8086:3582"
//#define I865STR "8086:2572"
#define I915STR "8086:2592"
+#define I945STR "8086:27a2"
#define MEMSTR "Memory at"
#define NONPRSTR "32-bit, non-prefetchable"
@@ -272,7 +273,8 @@
return p;
}
- i = (p = strstr(*buff_ptr, I855STR)) != NULL;
+ i = (p = strstr(*buff_ptr, I855STR)) != NULL ||
+ (p = strstr(*buff_ptr, I945STR)) != NULL;
if (i)
{
*chiptype = I855;
After this, the tool should be compiled and installed. I can provide RPM's for openSUSE 10.2 on request.
What is missing now is the interfacing between FN-F7 and i810switch and i810rotate. The latter should be used as it rotates from LCD-Only - LCD+CRT - CRT-Only with every new call.
Patching dockhandler
I included this in dockutils (/usr/lib/dockutils from dockutils-01), however, there are several optional ways how to do this. The patch in use is depicted below:
--- dockhandler 2006-11-06 18:22:37.000000000 +0100
+++ dockhandler 2007-03-02 12:44:53.000000000 +0100
@@ -70,6 +70,12 @@
elif [ "$SER" -eq 4107 ]; then # Fn+F9
ACTION=dock
fi
+ if [ "$SER" -eq 4098 ]; then # Fn+F2
+ ACTION=lockscreen
+ fi
+ if [ "$SER" -eq 4103 ]; then # Fn+F7
+ ACTION=videotoggle
+ fi
elif [ "$EVENT" = "ibm/dock" ]; then
case $VAL in
0) # X32 has strange dock code
@@ -81,7 +87,7 @@
fi
fi
-export MODEL=`hal-get-property --udi /org/freedesktop/Hal/devices/computer --key smbios.system.version`
+export MODEL=`hal-get-property --udi /org/freedesktop/Hal/devices/computer --key smbios.system.version | sed "y/abcdefghijklmnopqrstuvwxyz/ABCDEFGHIJKLMNOPQRSTUVWXYZ/"`
if [ -n "`echo $MODEL | grep -i thinkpad`" ]; then
HOOKDIR=thinkpad
--- hooks/thinkpad/60x60 2006-11-05 02:35:17.000000000 +0100
+++ hooks/thinkpad/60x60 2007-03-02 12:18:37.000000000 +0100
@@ -6,10 +6,25 @@
#
# This file is released under the GPLv2.
#
+# Modifications by Dr. Ing. Dieter Jurzitza / enhanced features
+#
. common_functions
-[ "$MODEL" == "Thinkpad X60" ] && exit 0;
+[ "$MODEL" = "THINKPAD X60" ] || exit 0;
+
+video_toggle(){
+ echo x60 video_toggle
+ /usr/sbin/i810rotate
+}
+
+lock_screen(){
+ echo x60 lock_screen
+ APPLICATION="/opt/kde3/bin/kdesktop_lock"
+ [ -f ${APPLICATION} ] || exit 0
+ USER=`/usr/bin/who -u | /bin/awk '{if(match($2, ":0")){print $1}}'`
+ sudo -u ${USER} /bin/bash -l -c "export DISPLAY=:0.0; ${APPLICATION} --forcelock &"
+}
if [ "$1" = "dock" ]; then
echo x60 dock
@@ -18,4 +33,12 @@
elif [ "$1" = "undock" ]; then
echo x60 undock
unregister_cdroms
+
+elif [ "$1" = "videotoggle" ]; then
+ echo x60 video toggle
+ video_toggle
+
+elif [ "$1" = "lockscreen" ]; then
+ echo x60 lock screen
+ lock_screen
fi
This patch does two things: firstly it repairs a bug in dockutils. The former comparison [ "MODEL" == "Thinkpad X60" ] && exit 0; ensures that the file 60x60 is processed for each notebook not named "Thinkpad X60" what is not what was meant here.
Functionally both the FN-F2 and FN-F7 keys are tested in dockhandler. Events are assigned that are called "lockscreen" for FN-F2 and "videotoggle" for FN-F7, correspondingly. The event "lockscreen" in turn triggers the function call "lock_screen()" from within 60x60, the same holds true for the event "videotoggle" and the function call to "video_toggle". Please make sure that the path to i810rotate in "video_toggle()" fits to your system environment.
After this, both keys FN-F2 and FN-F7 should do what you expect them to do. FN-F2 is adapted for the usage of kde, so your mileage may vary if you want to adapt it to gnome or other window managers.
If you do not want to struggle with those patches, let me know. I can provide rpm's for both i810switch and dockhandler that can simply replace the original ones and provide the functionality as described above. Send me an email if you need those.
The following commentary must have been caused due to problems with transferring the code described here to the local system:
The [ "MODEL" = XXX ]; then -line has been confirmed by SuSE (dockhandler author). If you run into issues with your X60 when implementing my suggestions, don't hesitate to contact me.
I have had to revert that change on my X60 /* MODEL = .... */
This is only another way to do it - and I think the elifs aren't appropriate because you'd think all key combinations are related to the Fn+F9 toggle, what is not the case.
I did changed the upper code into
elif [ "$SER" -eq 4107 ]; then # Fn+F9
ACTION=dock
elif [ "$SER" -eq 4098 ]; then # Fn+F2
ACTION=lockscreen
elif [ "$SER" -eq 4103 ]; then # Fn+F7
ACTION=videotoggle
fi
Activating the internal modem
Choosing the right modem driver
The internal modem can only be used with the hsfmodem-package that is available from http://www.linuxant.com. The current version is hsfmodem-7.60. I recommend *not* to use the "openSUSE" package but to switch to the "generic" package as the latter one rebuilds the module if the kernel version does not match. My experiments with the slmodem package have failed.
Suspend2ram / Suspend2disk issues with the modem driver
Installing this module encorporates issues with suspend2disk / suspend2ram. These are twofold. On one hand you have to make sure that the modules are being unloaded before performing a suspend2ram / suspend2disk process. Otherwise you will observe crashed. On the other hand the unloading of the intel sound module that is replaced by the hsf-package does not work as expected if i. e. kmix is running.
But step by step. First of all it must be ensured that the module is unloaded for sure if a susped2disk / suspend2 ram action should be performed. This can be achieved as follows:
This is done by placing a script in /etc/pm/hooks, I have chosen the name "08softmodem" and made it executable:
#!/bin/bash
. /etc/pm/functions
case "$1" in
hibernate|suspend)
/etc/init.d/hsf stop
;;
thaw|resume)
/etc/init.d/hsf start
;;
*)
;;
esac
exit $?
Secondly, given you want to unload this you have to make sure that the soundmodule is not bound to kmix any more. Therefore I created a second script called 06kmix located in the same directory to make sure that it is processed before the unloading of the modules is actually being processed:
#!/bin/bash
. /etc/pm/functions
KMIXPID=`ps ax | awk '{if (match($5, "kmix")){print $1}}'`
case "$1" in
hibernate|suspend)
kill -SIGHUP $KMIXPID
;;
thaw|resume)
;;
*)
;;
esac
exit $?
If both scripts are in place, suspending and resuming should work, however, kmix will be halted when you get out of the suspend and it will not restart automatically. I had received a suggestion to restard it using an event of kpowersaved did not work for me. But I realized it using a different technique.
I created a script called /home/<username>/.kde/Autostart/restartkmix with the following contents. It should be executeable as well:
#!/bin/sh
SLEEP=10
while [ 1 ]; do
PROCNUM=`ps ax | awk '{if(match($0," kmix")&&(!match($0,"awk"))){print $1}}'`
if [ "${PROCNUM}" = "" ]; then
kmix -autostart
fi
sleep $SLEEP
done
This generates a small amount of system load every 10 seconds but I think this is neglible. If kmix is not running it is restarted. This works perfectly for me.
Activating the fingerprint reader
There is a description of the fingerprint reader project at another location in this wiki (http://www.thinkwiki.org/wiki/Integrated_Fingerprint_Reader). The package (currently thinkfinger-0.2.2.tar.gz) should be downloaded, untared, built and installed. After that, you will have to do three things in addition:
1.) you need to modify /etc/pam.d/common-auth:
#%PAM-1.0
#
# This file is autogenerated by pam-config. All changes
# will be overwritten.
#
# Authentication-related modules common to all services
#
# This file is included from other service-specific PAM config files,
# and should contain a list of the authentication modules that define
# the central authentication scheme for use on the system
# (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the
# traditional Unix authentication mechanisms.
#
auth required pam_env.so
auth sufficient pam_thinkfinger.so
auth required pam_unix2.so
the line containing pam_thinkfinger.so needs to be added.
2.) you have to add a fingerprint from you. This is precisely described in the documentation of the thinkfinger package.
3.) you should change your default displaymanager to gdm, otherwise you will be able to use the fingerprint-reader only in console applications. This can be achieved by setting
DISPLAYMANAGER=gdm
in /etc/sysconfig/displaymanager.
Kernel upgrade to 2.6.21 and solving suspend2ram / suspend2disk stability issues
Stability issues
I had been facing suspend event related stability issues with the stock distribution system from the very begin. There were consistent freezes (see "Suspend2ram / Suspend2disk issues with the modem driver") I managed to solve. On top of this I experienced repetitive crashes from both suspend2ram / suspend2disk events and had no clue how to solve them. Those events were not deterministic, say every fourth or fifth suspend event there was a crash, the behaviour of suspend2ram was worse than that of suspend2disk, but both of them weren't reliable.
Stable suspend2ram / suspend2disk
Recently I decided to upgrade from stock kernel 2.6.18.8 to kernel 2.6.21-185 because the more recent kernels are said to be more robust with regard to suspend2disk / suspend2ram. However, initially I had no luck, apparently the very same behaviour appeared. But this time I got "oopses" from the e1000 module - though there was an entry in /etc/pm/config listing it as module that should be unloaded during suspend2ram / suspend2disk since the very begin:
SUSPEND_MODULES="button e1000"
Looking into /etc/pm/hooks I found that there is a file called 50modules, meant for unloading modules specified in SUSPEND_MODULES from /etc/pm/config, However, even moving 50modules to 04modules (to process this early) did not fix the problems, the crashes remained.
I started experimenting by stopping the interface and unloading the module by hand, and now: success! Say the wire bound ethernet interface is eth0 in your case, an
ifdown eth0
rmmod e1000
immediatly before suspend2ram / suspend2disk solved my issues. After restart, I had to add a
modprobe e1000
ifup eth0
to get the interface back into life. Either the script 50modules does not do what it is meant to do or the interface must be shut down prior to unloading the module. I thought it makes sense to add a small script to let this happen automatically. Call this file i. e. 04e1000 and put it into /etc/pm/hooks, do not forget to make it executable!
#!/bin/bash
. /etc/pm/functions
case "$1" in
hibernate|suspend)
ifdown eth0
rmmod e1000
;;
thaw|resume)
modprobe e1000
ifup eth0
;;
*)
;;
esac
exit $?
I was unable to cross check with the old kernel due to prior "experiments", so before following my path and upgrading the kernel, I strongly recommend to verify whether the manual procedure / the scriptlett alone probably solves everything and you can leave the kernel "as is". If you are not successful, you really might want to consider upgrading the kernel, too.
Generic solution / multiple network interfaces
After plugging another network interface into my X60 the name of the e1000-related network interface changed. I noticed this after new crashes with suspend2ram / suspend2disk. I decided that I didn't want to care about this any more and created a new script that unloads every network interface listed by ifconfig automatically. If you like this to happen, please consider the following script, I called it 04netmgnt.
#!/bin/bash
#
# This file makes sure that all netinterfaces and all corresponding modules
# are being shutdown at shutdown and restarted at reboot.
#
# Dr. Ing. Dieter Jurzitza, Karlsruhe, 2007
#
LS="/bin/ls"
SED="/bin/sed"
DEBUGFILE="/etc/pm/04unloadnet.dbg"
IFNAMEFILE="/etc/pm/ifnames-tmp"
IFCONFIG="/sbin/ifconfig"
IFUP="/sbin/ifup"
IFDOWN="/sbin/ifdown"
MODPROBE="/sbin/modprobe"
RMMOD="/sbin/rmmod"
SYS="/sys/class/net/"
SPATH="/device/driver/module/drivers/"
function getnetifnames(){
# call ifconfig, remove everything but interface-names!
# and remove "lo" since there is nothing to unload!
INTERFACES=(`${IFCONFIG} | ${SED} 's/[[:space:]].*//g;/^lo$/d;/^$/d'`)
# now we know all network interface names
# save those temporarily to $IFNAMEFILE, we need this at next restart.
# $INTERFACES is an array of the names we find.
i=0
echo -n "declare INTERFACES=(" > ${IFNAMEFILE}
while [ "${INTERFACES[$i]}" != "" ]; do
echo -n "${INTERFACES[$i]}" >> ${IFNAMEFILE}
i=`expr ${i} + 1`
if [ "${INTERFACES[$i]}" != "" ]; then
echo -n " " >> ${IFNAMEFILE}
fi
done
echo ")" >> ${IFNAMEFILE}
# now find the modules that belong to those interfaces!
# Same as before, now $MODULES is an array of modules corresponding
# to $INTERFACES
i=0
while [ "${INTERFACES[$i]}" != "" ]; do
MODULES[$i]=`${LS} ${SYS}${INTERFACES[$i]}${SPATH} | ${SED} 's/.*://g'`
i=`expr $i + 1`
done
# and write them to $IFNAMEFILE to store for the next reboot!
# Just like before.
i=0
echo -n "declare MODULES=(" >> ${IFNAMEFILE}
while [ "${MODULES[$i]}" != "" ]; do
echo -n "${MODULES[$i]}" >> ${IFNAMEFILE}
i=`expr ${i} + 1`
if [ "${MODULES[$i]}" != "" ]; then
echo -n " " >> ${IFNAMEFILE}
fi
done
echo ")" >> ${IFNAMEFILE}
}
function restartnetif () {
if [ -f ${IFNAMEFILE} ]; then
. ${IFNAMEFILE}
i=0
# ok. On startup, load each module and start the corresponding
# interface
while [ "${MODULES[$i]}" != "" ]; do
# just in case we'd like to see what happens.
# echo "${MODPROBE} ${MODULES[i]}" >> ${DEBUGFILE}
# echo "${IFUP} ${INTERFACES[i]}" >> ${DEBUGFILE}
${MODPROBE} ${MODULES[$i]}
${IFUP} ${INTERFACES[$i]}
i=`expr ${i} + 1`
done
rm -f ${IFNAMEFILE} > /dev/null 2>&1
fi
}
function shutdownnetif () {
declare -a INTERFACES
declare -a MODULES
getnetifnames
i=0
# ok. On shutdown, shut each interface down and unload the corresponding
# module.
while [ "${MODULES[$i]}" != "" ]; do
${IFDOWN} ${INTERFACES[$i]}
${RMMOD} ${MODULES[$i]}
i=`expr ${i} + 1`
done
}
case "$1" in
hibernate|suspend)
shutdownnetif
;;
thaw|resume)
restartnetif
# and finally restart the entire network!
/etc/init.d/network restart
;;
*)
;;
esac
exit $?
The script tries to detect each network interface automatically and determins the corresponding module. At suspend2ram / suspend2disk the interface is shut down and the module is unloaded. At resume the inverse process occurs. In order to "save state" the modules names / interface names are written into a temporary file that is removed after the next restart.
As always, if you consider playing with this and you think that errors can happen to easily while typing, I'd be pleased to provide the script if you like to try.
If you get the impression that there is something going wrong, you might want to try to keep the configuration files over a reboot. Just put a pound sign in front of the line
rm -f ${IFNAMEFILE} > /dev/null 2>&1
and you should be able to see what is written into /etc/pm/ifnames-tmp. Here it looks like:
declare INTERFACES=(eth0 eth1)
declare MODULES=(ipw3945 e1000)
These are two arrays apparently ok - this might vary as you put different network interfaces into your pcmcia slots or into one of the usb ports. Keep me informed if you experience something going wrong.
Kernel upgrade procedure
I downloaded the latest kernel from ftp.gwdg.de/pub/opensuse/repositories/Kernel:/HEAD/openSUSE_10.2. However I found that this branch has vanished in the meantime. So I suggest that if you are brave and you still want to install a kernel from the 2.6.21 series (as I did) you should use the one from the SL-OSS-factory tree:
ftp.gwdg.de/pub/opensuse/distribution/SL-OSS-factory/inst-source/suse/i586/kernel-default-2.6.21-12.i586.rpm
but be aware, I did not test it on my own until now (but this is on my todo list. I will test as soon as openSUSE 10.3 is released). Nevertheless I do not expect big differences to the kernel-default-2.6.21-185.i586.rpm I used from the path mentioned first in this chapter.
Between kernel 2.6.18 and 2.6.21 there were significant changes in the wlan interface. Due to this you should download and rebuild the following packages:
- the ipw3945 kernel module (ipw3945-kmp-default-1.2.0_2.6.21_12-3.i586.rpm), otherwise wlan won't work.
ipw3945d-1.7.18-31.i586.rpm can remain as-is, it need not be changed. The same is valid for ipw-firmware-7-31.i586.rpm.
- wpa_supplicant should be downloaded as source - rpm, recompiled and reinstalled. I used wpa_supplicant-0.5.7-21.src.rpm.
- madwifi should be upgraded, too. Download the source - rpm (madwifi-0.9.3-18.src.rpm), install it, rebuild the i586-rpm and install it.
After this you will still face the problem that wlan does not work - though the drivers are being loaded, you will get no connection to the wlan. This is caused by getcfg not returning the appropriate values. To circumvent this problems, you have to write
WIRELESS='yes'
into /etc/sysconfig/network/ifcfg-wlan-bus-pci-0000:03:00.0. Be aware that this is required every time you modify the wlan configuration. The only alternative would be to patch getcfg.
Getcfg is part of the package sysconfig, so you will have to get the sources for sysconfig and patch there. The required patch is shown here:
--- tools/get_config_lib.c.original 2007-05-24 22:19:33.000000000 +0200
+++ tools/get_config_lib.c 2007-05-24 22:19:25.000000000 +0200
@@ -31,6 +31,7 @@
int syslog_verbosity = LOG_EMERG;
char syslog_name [MAX_HWDESC_PART_LEN] = {'\0'};
const char *hwdesc_type_names[] = { HWDESC_TYPE_NAMES };
+const char *hwdesc_interface_names[] = { HWDESC_INTERFACE_NAMES };
const char *hwdesc_bus_names[] = { HWDESC_BUS_NAMES };
void error_log(int level, const char* message, ...) {
@@ -87,6 +88,11 @@
hwdesc->interfacepath[i]);
sprintf(varname, " %s_INTERFACEPATH_%d", prefix, i);
strcat(varlist, varname);
+ if (!strcmp(hwdesc->interfacetype[i], hwdesc_interface_names[4])){
+ adjust_network_type(hwdesc, i);
+ strcpy(hwdesc->interfacetype[i],
+ get_interface_name(hwdesc->interfaceclass[i]));
+ }
printf("%s_INTERFACETYPE_%d=\"%s\";\n", prefix, i,
hwdesc->interfacetype[i]);
sprintf(varname, " %s_INTERFACETYPE_%d", prefix, i);
This is nothing but a plaster, however, this works for me.
openSUSE specific issues
Make irqbalancer work
If you installed the "irqbalancer" package you probably realized that it is not running. Calling "/etc/init.d/irq_balancer status" will return "unused". Doing a "cat /proc/interrupts" will show all interrupts on CPU 0, CPU 1 will not process any interrupt. To solve this problem you should edit /etc/init.d/irq_balancer manually. Change the line
start)
echo -n "Starting irqbalance "
if [ $PHYS -gt 1 ] || [ $PROC -gt 1 -a $PHYS -eq 0 ] ; then
into
start)
echo -n "Starting irqbalance "
if [ $PHYS -gt 1 ] || [ $PROC -gt 1 -a $PHYS -eq 1 ] ; then
$PHYS should be compared to 1, not to 0. After restarting irq_balancer, the interrupts should be shared between cpu 0 and cpu 1 now. The important point is the change from $PHYS -eq 0 to $PHYS -eq 1.
This issue has been fixed recently, you can download irqbalance-0.55-12.src.rpm from OSS-factory tree, build and install (or you live with the small change as shown above!)
Avoiding duplicate s2ram / s2disk events
To provide certain functionality openSUSE 10.2 still keeps both pm-utils and powersave active. In future versions powersave shall vanish. For thinkpads the file /usr/lib/powersave/thinkpad_acpi_events takes care of those events. Unfortunately the s2ram and s2disk events are treated both in pm-utils and in powersave. This can have unwanted side effects; depending on the speed of action the powersave actions may be faster than the pm-util actions, thereby certain modules that should be removed might not be appropriately.
To get out of these problems it is highly recommended to modify the file /usr/lib/powersave/thinkpad_acpi_events accordingly. The following patch provides all neccessary changes to ensure this. This patch is against the source package of powersave.
--- scripts/thinkpad_acpi_events 2006-11-24 15:33:11.000000000 +0100
+++ scripts/thinkpad_acpi_events 2007-04-16 11:10:07.000000000 +0200
@@ -91,11 +91,7 @@
ACTION="blank screen"
fi
;;
- 4100) HOTKEY="Fn+F4"
- ACTION="suspend-to-ram"
- . $SYSCONF_DIR/sleep
- [ "$DISABLE_USER_SUSPEND2RAM" != "yes" ] && powersave "--$ACTION"
- ;;
+ 4100) HOTKEY="Fn+F4" ;;
4101) HOTKEY="Fn+F5" # Wireles LAN
if [ -x /opt/thinkpad/ac/onscreen_ac.sh ] ; then
run_on_xserver "/opt/thinkpad/ac/onscreen_ac.sh start" &
@@ -109,29 +105,16 @@
fi
;;
4102) HOTKEY="Fn+F6" ;;
- 4103) HOTKEY="Fn+F7"
- ACTION="swap monitors"
- echo video_switch > /proc/acpi/ibm/video
- ;;
+ 4103) HOTKEY="Fn+F7" ;;
4104) HOTKEY="Fn+F8" ;;
- # ACTION="expand screen"
- # echo expand_toggle > /proc/acpi/ibm/video
- 4105) HOTKEY="Fn+F9"
- # ACTION="undock"
- # handled by dockutils
- ;;
+ 4105) HOTKEY="Fn+F9" ;;
4106) HOTKEY="Fn+F10" ;;
4107) HOTKEY="Fn+F11" ;;
- 4108) HOTKEY="Fn+F12"
- ACTION="suspend-to-disk"
- . $SYSCONF_DIR/sleep
- [ "$DISABLE_USER_SUSPEND2DISK" != "yes" ] && powersave "--$ACTION"
- ;;
+ 4108) HOTKEY="Fn+F12" ;;
4109) HOTKEY="Fn+Backspace" ;;
4110) HOTKEY="Fn+Insert" ;;
4111) HOTKEY="Fn+Delete" ;;
- 4112) HOTKEY="Fn+Home"
- ACTION="brighter display" ;;
+ 4112) HOTKEY="Fn+Home" ;;
*) HOTKEY="Unidentified" ;;
esac
else
PCMCIA - slot
There is nothing special to say about the PCMCIA-slot. It just works (for me).
Integrating an (old) SIEMENS IGATE 11M PCMCIA-wlan card
I own an old IGATE 11M card (still fine for just surfing) I wanted to test on openSUSE 10.2. Unfortunately it did not work out of the box, so I describe here what I did to get it going. This issue is an openSUSE 10.2 problem and not specific to this wlan card.
This card is based on a prism chipset where a set of linux drivers are available (hostap, orinoco ..). When I used to work with SUSE 9.3 I had had success with the hostap driver so I had planned to use this one here, too.
Yast2 nicely detects the card and allows to configure everything including the appropriate encryption settings (wpa psk in this case). In /etc/sysconfig/hardware/hwcfg-bus-pcmcia-0.0 the hostap driver is entered so initially everything seemed to be alright.
However, the card was not working and I found that the orinoco driver had had been loaded - this was astonishing as YaST2 wrote "hostap_cs" int /etc/sysconfig/hardware/hwcfg-bus-pcmcia-0.0. This problem is caused by an error in /etc/modprobe.d/prism2. It causes the orinoco driver to always be loaded what messes up the entire configuration.
In order to avoid this, the file /etc/modprobe.d/prism2 should be modified. It basically contains a list of keys that ought to assign each individual (pcmcia-) card to a specific driver. Unfortunately there is an aliasing phenomenon so there are two matches for this card - one for the orinoco driver, one for the prism2 driver. The orinoco driver does not work with the card, the prism driver is not installed. A pointer to hostap is missing in the file.
To fix this, the following patch should be applied:
--- prism2.original 2006-11-25 16:50:35.000000000 +0100
+++ prism2 2007-05-28 10:36:46.000000000 +0200
@@ -58,7 +58,7 @@
alias pcmcia:m*c*f*fn*pfn*pa71B18589pbB6F1B0ABpc4B74BAA0pd* hostap_cs
alias pcmcia:m*c*f*fn*pfn*pa71B18589pbF144E3ACpc*pd* orinoco_cs
alias pcmcia:m*c*f*fn*pfn*pa71B18589pbF144E3ACpc4B74BAA0pd00000000* prism2_cs
-alias pcmcia:m*c*f*fn*pfn*pa74C5E40Dpb8304FF77pc4B74BAA0pd* prism2_cs
+alias pcmcia:m*c*f*fn*pfn*pa74C5E40Dpb8304FF77pc4B74BAA0pd* hostap_cs
alias pcmcia:m*c*f*fn*pfn*pa74C5E40DpbDB472A18pc*pd* hostap_cs
alias pcmcia:m*c*f*fn*pfn*pa78FC06EEpb45A50C1Epc*pd* prism2_cs
alias pcmcia:m*c*f*fn*pfn*pa78FC06EEpbDB9AA842pc*pd* prism2_cs
@@ -84,7 +84,6 @@
alias pcmcia:m0101c0777f*fn*pfn*pa*pb*pc*pd* hostap_cs
alias pcmcia:m0126c8000f*fn*pfn*pa*pb*pc*pd* hostap_cs
alias pcmcia:m0138c0002f*fn*pfn*pa*pb*pc*pd* hostap_cs
-alias pcmcia:m0156c0002f*fn*pfn*pa*pb*pc*pd* orinoco_cs
alias pcmcia:m01EBc080Af*fn*pfn*pa*pb*pc*pd* orinoco_cs
alias pcmcia:m01FFc0008f*fn*pfn*pa*pb*pc*pd* prism2_cs
alias pcmcia:m0250c0002f*fn*pfn*pa*pb*pc*pd* hostap_cs
This basically removes the reference to the orinoco driver and adds one to the hostap driver. This makes the card work (for me). However, it should be denoted that this may or may not work for other wlan cards that might rely on orinoco / prism2. But probably this is an useful hint where to search for potential issues.
What doesn't work yet
- Xinerama with external LCD
- Dual head with external LCD
What I haven't tested yet
- Embedded Security Subsystem (TCPA)
- Active Protection System (HDAPS)
- Maximum battery life
lscpi
> lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller AHCI (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02) 15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b4) 15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 09) 15:00.2 Generic system peripheral [Class 0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 18)