Difference between revisions of "Installing Ubuntu on a ThinkPad R60e"

From ThinkWiki
Jump to: navigation, search
m (Xorg.config for two screens)
(External Sources)
 
(60 intermediate revisions by 2 users not shown)
Line 1: Line 1:
 
== Overview ==
 
== Overview ==
There are no particular problems installing Ubuntu on a R60e.
+
There are no particular problems installing Ubuntu on a {{R60e}}.
  
The notes here refer to 6.06.1 install disk and subsequent updates. I am currently testing Feisty on the basis of a herd1 install and updates but without any modification of config files. Significant changes that apply to Edgy (6.10) and Feisty (7.04) are noted here.
+
=== versions ===
 +
Most of the information here is based on a clean install of 6.06.1 with upgrade to {{Ubuntu 7.10}} via {{Ubuntu 6.10}} and {{Ubuntu 7.04}}. Significant changes particular to these versions are noted here..
  
Ubuntu 6.10 "Edgy"
+
'''Ubuntu 6.10 "Edgy Eft"'''
  
 
If the wireless kill switch is active during boot, that is wireless and bluetooth are switched off, there is a high probability that a "soft lockup on CPU0" will occur during boot. Boot appears to be ok provided the wireless is on during boot. See [https://launchpad.net/distros/ubuntu/+source/linux-source-2.6.17/+bug/63418 Bug 63418].
 
If the wireless kill switch is active during boot, that is wireless and bluetooth are switched off, there is a high probability that a "soft lockup on CPU0" will occur during boot. Boot appears to be ok provided the wireless is on during boot. See [https://launchpad.net/distros/ubuntu/+source/linux-source-2.6.17/+bug/63418 Bug 63418].
  
Ubuntu 7.04 "Feisty"
+
The problem with the wireless kill switch seems to have been fixed in kernel 2.6.20.
Installs ok with Herd1 CD image. Upgrades to equiv of Herd2 ok some open office files need to be removed.
+
 
 +
'''{{Ubuntu 7.10}} "Gutsy Gibbon" '''
 +
The version of Xorg in Gutsy includes RandR version 1.2 this entails some significant revision of the config of X for two screens described at [[#Using_xrandr_with_Ubuntu_7.10]] below. See also [[Xorg RandR 1.2]]
  
 
== Partition and Boot ==
 
== Partition and Boot ==
Line 16: Line 19:
  
 
To repartion:
 
To repartion:
boot to Windows and immediately create a Rescue and Recover disk set. The first disc of the set must be a CD (though if you put a DVD in it will be formatted and writen as a CD disc); this is a bootable disc. The second stage of the disc writing process will write to either one DVD or 5 CDs. Restoring from these disks will restore to factory state, which means the entire  hard drive is reformatted. After the disc set is created it is not possible to create a second set.
+
boot to Windows and immediately create a Rescue and Recover disk set. The first disc of the set must be a CD (though if you put a DVD in it will be formatted and writen as a CD disc); this is a bootable disc. The second stage of the disc writing process will write to either one DVD or 5 CDs. Restoring from these disks will restore to factory state, which means the entire  hard drive is reformatted. After the disc set is created it is not possible to create a second set. (Although if you update the R+R program you can create a new backup CD/DVD.)
  
 
However, if you have a USB HD you can also create a Rescue and Recovery copy on that. I have not tried (sucessfully) but I it should be possible to boot and restore from a USB HD recovery set and preserve any new partitions provided that: the windows partition is not too small, and the Recovery partition is preserved.  
 
However, if you have a USB HD you can also create a Rescue and Recovery copy on that. I have not tried (sucessfully) but I it should be possible to boot and restore from a USB HD recovery set and preserve any new partitions provided that: the windows partition is not too small, and the Recovery partition is preserved.  
Line 26: Line 29:
 
boot Ubuntu Live CD and install
 
boot Ubuntu Live CD and install
  
The live CD will install GRUB to the MBR, this is ok, the installer will identify both IBM_PRELOAD and the service partition and provide boot options for both. Edit  
+
The live CD will install GRUB to the MBR. For most users with a simple dual boot (Linux + Win) this will be fine; the installer will identify both IBM_PRELOAD and the service partition and provide boot options for both. (If you have need of a more complex boot arrangement, such as multiple linux versions then install using the Ubuntu '''alternate''' install CD.) Edit  
 
{{path|/boot/grub/menu.lst}} to add the hide and unhide lines (this will prevent Windows showing the Service Partition).
 
{{path|/boot/grub/menu.lst}} to add the hide and unhide lines (this will prevent Windows showing the Service Partition).
  
Line 48: Line 51:
  
 
== Kernel ==
 
== Kernel ==
The default kernel at install will be linux-image-386. Install Base System linux-image-686 for full support of the core-duo processor including SMP. (The older linux-image-SMP kernel is not required and may not perform as well as it is intended for servers and does not have the pre-emption patches.) You will also need  Base System (restricted) linux-restricted-modules-686 as the Intel wireless card driver loads binary firmware.
 
  
For Edgy-Eft (6.10) the default kernel linux-image-generic will fully support SMP so installing a kernel should not be necessary.
+
For current versions (from 6.10) the default kernel ''linux-image-generic'' will fully support SMP and CoreDuo processors so installing a kernel should not be necessary. Restricted modules are required for the Intel wireless card.
  
 
== Xorg.config for two screens ==
 
== Xorg.config for two screens ==
  
Intel 945GM
+
For Ubuntu Gutsy (7.10 alpha) see section below and [[Xorg RandR 1.2]]. Note also that if upgrading to Gutsy from Feisty the old Xorg.conf will be retained and  the i810 rather than the Intel driver will be used. The graphical configuration at System: Administration: Screens and Graphics (displayconfig-gtk) may be usable with the i810 driver, whereas it will probably wreck your xorg.conf if used with the Intel driver.
The config options are described in the driver man page {{cmduser|man i810}}. The following sections are for a configuration with the laptop screen as the primary display and an second display on the D-SUB15 analog VGA port. The second display is expected to be a flat panel or a data projector ('beamer').
+
 
 +
===Intel 945GM with the i810 driver===
 +
The i810 driver is used in versions before {{Ubuntu 7.10}}.
 +
Configuration options are described in the driver man page {{cmduser|man i810}}. The following sections are for a configuration with the laptop screen as the primary display and an second display on the D-SUB15 analogue VGA port. The second display is expected to be a flat panel or a data projector ('beamer').
 
There are some tradeoffs with Xorg.conf, the version below is intended to give the best available resolution with a variety of external screens without the need to change xorg.conf. See the notes at the end of this section for some other optimisations.
 
There are some tradeoffs with Xorg.conf, the version below is intended to give the best available resolution with a variety of external screens without the need to change xorg.conf. See the notes at the end of this section for some other optimisations.
  
Line 73: Line 78:
 
     Screen 1
 
     Screen 1
  
     # some additional possibilities
+
     # some additional possibilities (see man i810 for cryptic explanations)
     # Option "CheckLid" "no"
+
     # Option "CheckLid" "yes"
 
     # Option "Clone" "no"
 
     # Option "Clone" "no"
 
     # Option "CloneRefresh" "60"
 
     # Option "CloneRefresh" "60"
 
     # Option "FlipPrimary" "no"
 
     # Option "FlipPrimary" "no"
 
     # Option  "DisplayInfo" "yes"
 
     # Option  "DisplayInfo" "yes"
     # Option "Rotate" "CCW"
+
     # Option "Rotate" "0"
 +
    #  Option  "DevicePresence" "true"
 +
    #  Option  "LinearAlloc" "0"
 +
    #  Option  "Legacy3D"      "no"
 +
    #  Option  "AperTextSize"  "32768"
 
     EndSection
 
     EndSection
  
Line 175: Line 184:
 
     DefaultDepth 24
 
     DefaultDepth 24
 
     SubSection "Display"
 
     SubSection "Display"
    Depth 24
+
        Depth 24
Modes "1024x768" "1280x1024" "1600x1200" "640x480" "600x800"
+
            Modes   "1024x768" "1280x1024" "1600x1200" "640x480" "600x800"
 
     EndSubSection
 
     EndSubSection
 
     EndSection
 
     EndSection
Line 193: Line 202:
  
 
This may be a better config if you always use the same external screen, but less satisfactory if you need to connect to a variety of external screens.
 
This may be a better config if you always use the same external screen, but less satisfactory if you need to connect to a variety of external screens.
 +
 +
===Intel 945GM with the xorg Intel driver===
 +
This driver is used by {{Ubuntu 7.10}} and later.
 +
With X version 7.3 and xrandr version 1.2 the configuration of X for more than one screen is simplified. This section only covers {{Ubuntu 7.10}} and the {{R60e}} for other hardware and distributions see [[Xorg RandR 1.2]]
 +
 +
'''X RandR '''is used to set the size, orientation and reflection of the screen display outputs.
 +
 +
'''xrandr''' is the command line interface to the RandR X extension. As usual with X good documentation is hard to find, start with:
 +
 +
* [http://www.intellinuxgraphics.org/dualhead.html Intel's Dual head instructions]
 +
 +
then look at:
 +
* {{cmduser|xrandr --help}}
 +
* {{cmduser|man xrandr}}
 +
* {{cmduser|man intel}}
 +
 +
 +
If upgrading from earlier versions your old xorg.conf file may contain much that is now obsolete, so in what follows I will assume that you are starting with a fresh version of /etc/X11/xorg.conf which can be generated by
 +
 +
    {{cmdroot|sudo dpkg-reconfigure -phigh xserver-xorg}}
 +
 +
and then restarting X. With Gutsy ({{Ubuntu 7.10}}) using the graphical configuration (displyconfig-gtk) is likely to damage your xorg.config resulting in a 800x600 default display on reboot. In which case the above option will be useful.
 +
 
 +
The resulting {{path|/etc/X11/xorg.conf}} should include something like
 +
 +
    Section "Device"
 +
        Identifier "Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
 +
        Driver "intel"
 +
        BusID "PCI:0:2:0"
 +
        '''# ADD THIS IF YOUR LAPTOP DOES NOT HAVE A TV CONNECTOR or DOCKING STATION '''
 +
        '''Option          "monitor-TV"  "TV" '''
 +
    EndSection
 +
    Section "Monitor"
 +
        Identifier "Generic Monitor"
 +
        Option "DPMS"
 +
    EndSection
 +
  ''' # ADD THIS IF YOUR LAPTOP DOES NOT HAVE A TV CONNECTOR or DOCKING STATION '''
 +
  '''Section "Monitor" '''
 +
        '''Identifier      "TV" '''
 +
        '''Option          "Ignore" "True" '''
 +
  '''EndSection '''
 +
    Section "Screen"
 +
        Identifier "Default Screen"
 +
        Device "Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
 +
        Monitor "Generic Monitor"
 +
        DefaultDepth 24
 +
        SubSection "Display"
 +
            Depth 24
 +
            '''# ADD A VIRTUAL LINE TO PROVIDE FOR THE LARGEST SCREENS YOU WILL HOTPLUG'''
 +
            '''Virtual              2048 2048 '''
 +
        EndSubSection
 +
    EndSection
 +
    Section "ServerLayout"
 +
        Identifier "Default Layout"
 +
        Screen "Default Screen"
 +
        InputDevice "Generic Keyboard"
 +
        InputDevice "Configured Mouse"
 +
        InputDevice    "stylus" "SendCoreEvents"
 +
        InputDevice    "cursor" "SendCoreEvents"
 +
        InputDevice    "eraser" "SendCoreEvents"
 +
        InputDevice "Synaptics Touchpad"
 +
    EndSection
 +
 +
The example above contains some modifications:
 +
* The '''Virtual''' line. It is a limitation of the Intel driver that frame buffer size cannot be changed once X has started. Therefore in order to hotplug a variety of screens this should be set the allow for the largest combination of display resolutions you plan to use. For the Intel 945 chip in the {{R60e}} a virtual size larger than 2048 will disable DRI. (If you do not need 3D graphics that is not important.) By default the Virtual size is set to that of the largest display that is connected when X starts. (Note this means that if an external VGA is connected but not switched on it will still influence the virtual display size.)
 +
xrandr is a Xinerama mode, the mouse and application windows move about the entire virtual screen, the physical monitors provide a display port view of a portion of that space. So if you want the laptop LCD and an external  monitor to show different information the virtual size must be larger than the default.
 +
 +
[[Image:Intel-DualHead.png|monitor windows must fit within the virtual screen]]
 +
 +
* The Monitor and Device sections for '''Monitor-TV'''.  The {{R60e}} does not have a TV out socket though the graphics chip provides this capability. Disabling the TV will prevent the screen of the external monitor blanking for a few seconds whenever the xrandr program is used. (Later versions of the Intel driver may have a fix for this problem.)
 +
 +
* The new minimalist xorg.conf should not need modelines, nor should it include HorizSync and VertRefresh in the Monitor section. For some screens (eg Dell 2001FP) it appears that xrandr will not provide the maximum display resolution when these options are present.
 +
 +
=== Using ''xrandr'' with {{Ubuntu 7.10}} ===
 +
There is a  Graphical Configuration Tool, ([https://launchpad.net/ubuntu/+source/displayconfig-gtk/0.2+20070731ubuntu1 displayconfig-gtk]) included with {{Ubuntu 7.10}}. At present [https://bugs.launchpad.net/ubuntu/+source/displayconfig-gtk it dosn't work too well].It is found in the menu: 'System: Administration: Screens and Graphics'. As using it will wreck your xorg.conf (see above) I recommend removing it. 
 +
 +
The command line xrandr however does work quite well. Note that Gnome places the menu bar on screen 0 and that limitations of the Intel chip and driver mean this Screen 0 (the external VGA monitor) will always be the default display if it is connected. This applies even if the external monitor is switched off but the cable connected: if you have a blank laptop monitor check if you have anything plugged in to the VGA port.
 +
 +
So, if you start X with an external monitor connected that will be the only display until you use xrandr to change things.
 +
 +
Open a terminal window to use the command line: 'Applications:Accessories:Terminal'
 +
 +
First look at the 'help' and 'man' pages.
 +
{{cmduser|xrandr --help}}
 +
{{cmduser|man xrandr}}
 +
 +
To query what we have (nothing connected to VGA)
 +
{{cmduser| xrandr -v}}
 +
    Server reports RandR version 1.2
 +
 +
{{cmduser| xrandr -q }}
 +
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 1920 x 1440
 +
VGA disconnected (normal left inverted right)
 +
  LVDS connected 1024x768+0+0 (normal left inverted right) 304mm x 228mm
 +
    1024x768      60.0*+  50.0 
 +
    800x600        60.3 
 +
    640x480        60.0    59.9 
 +
TV disconnected (normal left inverted right)
 +
 +
If you see the 'TV disconnected' line but have neither TV connector nor docking station (eg Thinkpad R60e) then add to the Monitor and Device sections of xorg.conf as noted above. This will prevent the external (VGA) flashing off for a few seconds every time xrandr is used. (Newer versions of the intel driver may fix this.)
 +
 +
Example with the external monitor connected,  powered on and a Virtual 2624x2048. (For some reason my monitor defaults to 1280x800 for its initial display so two further xrandr commands are reguired to set up.)
 +
{{cmduser| xrandr -q }}
 +
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 2624 x 2048
 +
VGA connected 1280x800+0+0 (normal left inverted right) 367mm x 275mm
 +
    1600x1200      60.0 +  59.9 
 +
    1280x1024      75.0    59.9 
 +
    1152x864      74.8 
 +
    1024x768      75.1    60.0 
 +
    800x600        75.0    60.3 
 +
    640x480        75.0    60.0 
 +
    720x400        70.1 
 +
LVDS connected (normal left inverted right)
 +
    1024x768      60.0 +  50.0 
 +
    800x600        60.3 
 +
    640x480        60.0    59.9 
 +
  1280x800 (0x46)  83.5MHz
 +
        h: width  1280 start 1344 end 1480 total 1680 skew    0 clock  49.7KHz
 +
        v: height  800 start  801 end  804 total  828          clock  60.0Hz
 +
{{cmduser|xrandr  --output LVDS --auto}}
 +
{{cmduser|xrandr  --output VGA --mode 1600x1200 --pos 1024x0 }}
 +
 +
More information for bug reports
 +
{{cmduser| xrandr --verbose}}
 +
 +
{{cmduser| xrandr --output LVDS --auto}}
 +
gets two screens but both at 1600x1200 cloned
 +
 +
{{cmduser| xrandr --output LVDS --mode 1024x768 --output VGA --off }}
 +
gets laptop only at 1024x768
 +
 +
Without a virtual set in xorg.conf
 +
{{cmduser| xrandr --output VGA --right-of LVDS --mode 1600x1200 }}
 +
    xrandr: screen cannot be larger than 1600x1600 (desired size 2624x1200)
 +
 +
{{cmduser| xrandr --output VGA  --mode 1600x1200 --pos 0x400 }}
 +
creates two screens with the laptop screen at  bottom of the 1600x1600 window
 +
 +
{{cmduser| xrandr --output LVDS --mode 1024x768 --pos 0x400 }}
 +
moves laptop screen to top of window, so both share same top line
 +
 +
{{cmduser| xrandr  --output VGA --mode 1600x1200 --pos 0x768}}
 +
  xrandr: screen cannot be larger than 1600x1600 (desired size 1600x1968)
 +
 +
edit xorg.conf and ensure we have '''Virtual 2048 2048'''. Try again and it works: we have a laptop screen in a virtual position at the top of a 2048x2048 frame with the VGA monitor below.
 +
 +
Next edit xorg.conf and set '''Virtual 2624 2048 ''' then:
 +
 +
{{cmduser| xrandr  --output VGA --mode 1600x1200 --pos 1024x0}}
 +
 +
Now it is possible to have the two windows side by side.
 +
 +
see also [[Sample Fn-F7 script]] to use xrandr with function key F7
 +
 +
* References
 +
** '''VGA'''    Analog VGA output
 +
** '''LVDS'''  Laptop panel
 +
** [http://gitweb.freedesktop.org/?p=xorg/proto/randrproto.git;f=randrproto.txt;a=blob RandR 1.2 protocol specifications]
 +
** [http://www.intellinuxgraphics.org/  Linux Graphics Drivers from Intel]
 +
** [https://launchpad.net/ubuntu/+source/xserver-xorg-video-intel/ Ubuntu source for Intel]
 +
** [http://lists.freedesktop.org/archives/xorg/ FreeDesktop.org Xorg archive]
 +
**[http://wiki.x.org/wiki/Development/Documentation/HowVideoCardsWork How video cards work]
 +
 +
== Screen Brightness control ==
 +
In 7.04 there is a problem with the Fn+home Fn+End screen brightness controls [https://bugs.launchpad.net/bugs/87028 Bug 87028].
 +
 +
The [http://www.mail-archive.com/ibm-acpi-devel@lists.sourceforge.net/msg00092.html workaround] is to disable video.o
 +
 +
echo blacklist video | sudo tee -a /etc/modprobe.d/local
 +
 +
Unfortunately this only fixes the blanking screen, using the Fn+Home and Fn+End provides values of bright and dim but no intermediate values [https://bugs.launchpad.net/bugs/61184 Bug 61184]. A fix has been posted. First check what you have
 +
  # lshal|grep smbios.system
 +
  smbios.system.version = 'ThinkPad R60e'  (string)
 +
  smbios.system.product = '06574TG'  (string)
 +
  smbios.system.manufacturer = 'LENOVO'  (string)
 +
 +
then edit /usr/share/hal/fdi/policy/10osvendor/10-laptop-panel-mgmt-policy.fdi
 +
 +
# sudo nano -w  /usr/share/hal/fdi/policy/10osvendor/10-laptop-panel-mgmt-policy.fdi
 +
 +
The original release 7.04 had a <device> block for LENOVO that tested the version string for X, T, and Z model ThinkPads but not R. A subsequent update to hal has modified the file to <deviceinfo version="0.2"> and removed the Lenovo specific code. Add to the file
 +
 +
  <device>
 +
    <match key="info.category" string="laptop_panel">
 +
      <match key="/org/freedesktop/Hal/devices/computer:smbios.system.manufacturer" string="LENOVO">
 +
        <match key="/org/freedesktop/Hal/devices/computer:smbios.system.version" contains="ThinkPad R">
 +
          <merge key="laptop_panel.brightness_in_hardware" type="bool">true</merge>
 +
        </match>
 +
      </match>
 +
    </match>
 +
  </device>
 +
 +
save the file then 
 +
# sudo /etc/dbus-1/event.d/20hal restart
 +
and restart X (Ctrl+Alt+Backspace)
 +
Note: the onscreen bar display will not display the changed level.
  
 
== Sound ==
 
== Sound ==
Line 202: Line 407:
 
     # echo -n 96 > /sys/devices/platform/i8042/serio0/speed
 
     # echo -n 96 > /sys/devices/platform/i8042/serio0/speed
 
     # echo -n 200 > /sys/devices/platform/i8042/serio0/sensitivity
 
     # echo -n 200 > /sys/devices/platform/i8042/serio0/sensitivity
 +
 +
and with Ubuntu 7.10 (Gutsy)
 +
 +
    # echo -n 96 > /sys/devices/platform/i8042/serio1/speed
 +
    # echo -n 200 > /sys/devices/platform/i8042/serio1/sensitivity
  
 
This needs to be typed in a root window; using sudo gives a permission denied.
 
This needs to be typed in a root window; using sudo gives a permission denied.
  
 
== Wireless ==
 
== Wireless ==
Works if you install linux-image which depends on linux-restricted-modules-generic, which in turn contains the kernel module ath_pci. ath_pci is loaded automatically at system startup.
+
You need to install linux-restricted-modules-generic, which contains the kernel module ath_pci. ath_pci is loaded automatically at system startup.
 +
 
 +
Feisty (7.04) includes network-manager, although useful for roaming it dosn't work well for networks which do not broadcast ESSID.
  
 
== Suspend-to-RAM ==
 
== Suspend-to-RAM ==
Line 219: Line 431:
 
     /etc/acpi/sleep.sh
 
     /etc/acpi/sleep.sh
 
   fi
 
   fi
 +
 +
''7.04 (Feisty)''
 +
 +
Both Sleep (fn+4) and Hibernate (fn+12) appear to work.
  
 
== Modem ==
 
== Modem ==
Line 232: Line 448:
 
{{key|Fn}}{{key|F3}} Display Battery Condition
 
{{key|Fn}}{{key|F3}} Display Battery Condition
  
{{key|Fn}}{{key|F4}} Sleep can be configured in Gnome power save option, but seems to disable fn+F12 hibernate; 'blank screen' sets screensaver)  
+
{{key|Fn}}{{key|F4}} Sleep can be configured in Gnome power save option, but seems to disable fn+F12 hibernate; 'blank screen' sets screensaver (6.04 Dapper).
 +
Works without additional configuration (7.04 Feisty).
  
 
{{key|Fn}}{{key|F5}} toggle Wireless/Bluetooth on/off
 
{{key|Fn}}{{key|F5}} toggle Wireless/Bluetooth on/off
  
{{key|Fn}}{{key|F7}} Switch Screen? (no ibm/hotkey shown with {{cmduser|acpi_listen}} only effective if cloned displays?)
+
{{key|Fn}}{{key|F7}} Switch Screen (HKEY 00000080 00001007) see [[Sample_Fn-F7_script]]
  
 
{{key|Fn}}{{key|F8}} TrackPoint? No Effect (ibm/hotkey HKEY 00000080 00001008)
 
{{key|Fn}}{{key|F8}} TrackPoint? No Effect (ibm/hotkey HKEY 00000080 00001008)
Line 242: Line 459:
 
{{key|Fn}}{{key|F9}} (ibm/hotkey HKEY 00000080 00001009) (Easy Eject in WinXP)
 
{{key|Fn}}{{key|F9}} (ibm/hotkey HKEY 00000080 00001009) (Easy Eject in WinXP)
  
{{key|Fn}}{{key|F12}} Suspend to disk, seems to work, but not entirely reliable, some scrambling of text console display during restart Sometimes restart hangs after reading disk, need to deactivate/reactivate wireless.
+
{{key|Fn}}{{key|F12}} Suspend to disk, seems to work, but not entirely reliable, some scrambling of text console display during restart Sometimes restart hangs after reading disk, need to deactivate/reactivate wireless. (6.06 Dapper).
 +
Does not appear to work (7.04 Feisty).
  
{{key|Fn}}{{key|Home}} screen brighter (ibm/hotkey HKEY 00000080 00001010)  
+
{{key|Fn}}{{key|Home}} screen brighter (ibm/hotkey HKEY 00000080 00001010)
 +
(see notes above to fix regressions since 6.06 Dapper)  
  
 
{{key|Fn}}{{key|End}} screen dims (no ibm/hotkey shown with {{cmduser|acpi_listen}})  
 
{{key|Fn}}{{key|End}} screen dims (no ibm/hotkey shown with {{cmduser|acpi_listen}})  
Line 251: Line 470:
  
 
=External Sources=
 
=External Sources=
 +
*[http://www.linlap.com/wiki/IBM-Lenovo+Thinkpad+R60e General Linux guide for the ThinkPad R60e]
 
*This guide is listed at the [http://tuxmobil.org/ibm.html TuxMobil Linux laptop and notebook installation survey (IBM/Lenovo)].
 
*This guide is listed at the [http://tuxmobil.org/ibm.html TuxMobil Linux laptop and notebook installation survey (IBM/Lenovo)].
  
[[Category:R60e]] [[Category:Ubuntu]]
+
[[Category:R60e]]

Latest revision as of 07:00, 2 March 2008

Overview

There are no particular problems installing Ubuntu on a R60e.

versions

Most of the information here is based on a clean install of 6.06.1 with upgrade to Ubuntu 7.10 via Ubuntu 6.10 and Ubuntu 7.04. Significant changes particular to these versions are noted here..

Ubuntu 6.10 "Edgy Eft"

If the wireless kill switch is active during boot, that is wireless and bluetooth are switched off, there is a high probability that a "soft lockup on CPU0" will occur during boot. Boot appears to be ok provided the wireless is on during boot. See Bug 63418.

The problem with the wireless kill switch seems to have been fixed in kernel 2.6.20.

Ubuntu 7.10 "Gutsy Gibbon" The version of Xorg in Gutsy includes RandR version 1.2 this entails some significant revision of the config of X for two screens described at #Using_xrandr_with_Ubuntu_7.10 below. See also Xorg RandR 1.2

Partition and Boot

If the Windows and Service Partitions are to be retained then the Gnome Partition Editor can be used from the live cd to shrink the Windows partition (sda1). The IBM recovery partition is placed at the end of the HD disk and contains a cut down version of WinNT. Note that the Recovery partion is not located on a cylinder boundary and is placed between 'unused' disk areas, 3MB in front and 7MB behind. These appear to contain the diagnostics programs and should not be moved or resized if the diagnostics and R&R programs are required.

To repartion: boot to Windows and immediately create a Rescue and Recover disk set. The first disc of the set must be a CD (though if you put a DVD in it will be formatted and writen as a CD disc); this is a bootable disc. The second stage of the disc writing process will write to either one DVD or 5 CDs. Restoring from these disks will restore to factory state, which means the entire hard drive is reformatted. After the disc set is created it is not possible to create a second set. (Although if you update the R+R program you can create a new backup CD/DVD.)

However, if you have a USB HD you can also create a Rescue and Recovery copy on that. I have not tried (sucessfully) but I it should be possible to boot and restore from a USB HD recovery set and preserve any new partitions provided that: the windows partition is not too small, and the Recovery partition is preserved.

boot with Ubuntu live CD, use Gnome Partition editor to shrink the IBM_PRELOAD (sda1) partition.

reboot to Windows and let it run chkdsk

boot Ubuntu Live CD and install

The live CD will install GRUB to the MBR. For most users with a simple dual boot (Linux + Win) this will be fine; the installer will identify both IBM_PRELOAD and the service partition and provide boot options for both. (If you have need of a more complex boot arrangement, such as multiple linux versions then install using the Ubuntu alternate install CD.) Edit /boot/grub/menu.lst to add the hide and unhide lines (this will prevent Windows showing the Service Partition).

 # This entry automatically added by the Debian installer for a non-linux OS
 # on /dev/sda1
 title           Microsoft Windows XP Professional
 hide            (hd0,1)
 root            (hd0,0)
 savedefault
 makeactive
 chainloader     +1
 # This entry automatically added by the Debian installer for a non-linux OS
 # on /dev/sda2
 title         IBM/Lenovo Maintenance
 unhide        (hd0,1)
 root          (hd0,1)
 savedefault
 makeactive
 chainloader   +1

Kernel

For current versions (from 6.10) the default kernel linux-image-generic will fully support SMP and CoreDuo processors so installing a kernel should not be necessary. Restricted modules are required for the Intel wireless card.

Xorg.config for two screens

For Ubuntu Gutsy (7.10 alpha) see section below and Xorg RandR 1.2. Note also that if upgrading to Gutsy from Feisty the old Xorg.conf will be retained and the i810 rather than the Intel driver will be used. The graphical configuration at System: Administration: Screens and Graphics (displayconfig-gtk) may be usable with the i810 driver, whereas it will probably wreck your xorg.conf if used with the Intel driver.

Intel 945GM with the i810 driver

The i810 driver is used in versions before Ubuntu 7.10. Configuration options are described in the driver man page $ man i810. The following sections are for a configuration with the laptop screen as the primary display and an second display on the D-SUB15 analogue VGA port. The second display is expected to be a flat panel or a data projector ('beamer'). There are some tradeoffs with Xorg.conf, the version below is intended to give the best available resolution with a variety of external screens without the need to change xorg.conf. See the notes at the end of this section for some other optimisations.

   Section "Device"
   	Identifier	"Intel 945GM Internal LCD"
   	Driver		"i810"
   	BusID		"PCI:0:2:0"
   	Screen 0
   	Option 	"MonitorLayout" 	"CRT,LFP"
       VideoRAM        126976
   EndSection
   Section "Device"
   	Identifier	"Intel 945GM External D-SUB15"
   	Driver		"i810"
   	BusID		"PCI:0:2:0"
   	Screen 1
   # some additional possibilities (see man i810 for cryptic explanations)
   #	Option	"CheckLid" 	"yes"
   # 	Option 	"Clone" 	"no"
   #	Option 	"CloneRefresh"	"60"
   # 	Option 	"FlipPrimary" 	"no"
   # 	Option  "DisplayInfo" 	"yes"
   #	Option 	"Rotate" 	"0"
   #   Option  "DevicePresence" "true"
   #   Option  "LinearAlloc"	"0"
   #   Option  "Legacy3D"      "no"
   #   Option  "AperTextSize"  "32768"
   EndSection

Resolution and timing

X and the graphics adaptor will detect an external screen if present and attempt to auto negotiate an appropriate resolution and refresh rate. It is unclear from the Xorg/XFree documentation how the useable video modes are selected/rejected but it appears that if a monitor is connected to the VGA connector the highest available VESA resolution will not be selected unless it has a refresh rate of 75Hz or more. As the optimum refresh rate for a flat panel display is usualy 60Hz, and often the highest (native) resolution only available at this rate, it may be necessary to set a mode line for best performance.

In the case of a data projector, these appear designed to accept inputs for resolutions and refresh rates far in excess of their native SVGA or XGA capabilities and automaticaly convert down, which may entail a loss of image quality. Thus, for these also, forcing a reasonable resolution and refresh rate is desirable.

The possible modes for a connected monitor can be discovered by looking at the X log file $ sudo nano -w /etc/X11/xorg.conf or by running $ xvidtune.

   Section "Modes"
   	Identifier 	"V75"
   	ModeLine "VGA 75"   31.50  640  656  720  840  480  481  484  500 
    	ModeLine "SVGA 75"  49.50  800  816  896 1056  600  601  604  625 
   	ModeLine "XGA 75"   78.80 1024 1040 1136 1312  768  769  772  800 
   	Modeline "SXGA 75" 135.00 1280 1296 1440 1688 1024 1025 1028 1066
   EndSection
   Section "Modes"
   	Identifier 	"V60"
   	Modeline "XGA 60"   65.00 1024 1048 1184 1344  768  771  777  806 
   	ModeLine "SXGA 60" 108.00 1280 1328 1440 1688 1024 1025 1028 1066
   	ModeLine "UXGA 60" 160.00 1600 1664 1856 2160 1200 1201 1204 1250 
   EndSection

The monitor

Most recent monitors will supply X with data on available built in modes, and this will overide the HorizSync and VertRefresh values in the config file. However some projectors do not supply this information and fail to display unless the HorizSync and VertRefresh are configured.

   Section "Monitor"
   	Identifier	"LCD on D-SUB15"
   	Option		"DPMS"
   	HorizSync	31-75
   	VertRefresh 	59-75
    	UseModes 	"V60"
   	UseModes	"V75"
   EndSection
   Section "Screen"
   	Identifier	"External Screen"
   	Device		"Intel 945GM External D-SUB15"
   	Monitor		"LCD on D-SUB15"
   	DefaultDepth	24
   	SubSection "Display"
   		Depth		24
   #		Modes		"1024x768" "1280x1024" "1600x1200" "640x480" "600x800"
   		Modes 		"XGA 60" "SXGA 60" "UXGA 60" "VGA 75" "SVGA 75"
   	EndSubSection
   EndSection
   Section "Screen"
   	Identifier	"Laptop LCD"
   	Device		"Intel 945GM Internal LCD"
   	Monitor		"Lenovo 15in LCD"
   	DefaultDepth	24
   	SubSection "Display"
   		Depth		24
   		Modes		"1024x768"
   #		Virtual         1600 1200
   #		ViewPort 	0 0
   	EndSubSection
   EndSection
   Section "ServerLayout"
   	Identifier	"Default Layout"
   	Screen		0 "Laptop LCD" Absolute 0 0
   	Screen		1 "External Screen" RightOf "Laptop LCD"
   #	Screen 		1 "External Screen" Absolute 1024 0
   	InputDevice	"Generic Keyboard"
   	InputDevice	"Configured Mouse"
   EndSection

Note 1 With this layout the mouse will move off the right hand edge of the laptop screen and make an entrance on the left of the external monitor. If you can't find the mouse it may be on the other screen, try moving it top left.

Note 2 The gnome desktop can be configured for each monitor. But it is not possible to transfer a window from on display to the other. Trying to start Firefox on one desktop when it is opened on another monitor will give a message: "Firefox is already running, but is not responding. To open a new window you must first close the existing Firefox process, or restart your system".

Xinerama To be able to drag windows from one screen to another and fix the problem in Note 2, enable Xinerama extension. However with Xinerama enabled the resolution of the external display will default to XGA, the same as the laptop screen. The Gnome menu System:Preferences:Screen Resolution will respond with: "The X Server does not support the XRandR extension. Runtime resolution changes to the display size are not available", nor will Gnome provide a separate desktop task bar etc. note [here] This problem can be overcome by defining the preferred resolution - and only that resolution - for the screen and server layout. eg.

   Section "Monitor"
       Identifier      "Dell 2001FP"
       DisplaySize     408 306
       Option          "DPMS"
       HorizSync       31-80
       VertRefresh     56-76
       ModeLine        "1600x1200" 160.00 1600 1664 1856 2160 1200 1201 1204 1250
   EndSection
   Section "Screen"
   	Identifier	"External UXGA"
   	Device		"Intel 945GM External D-SUB15"
   	Monitor		"DELL 2100FP"
   	DefaultDepth	24
   	SubSection "Display"
   	    Depth		24
           Modes    "1024x768" "1280x1024" "1600x1200" "640x480" "600x800"
   	EndSubSection
   EndSection
   Section "ServerLayout"
       Identifier      "Default Layout"
       Screen          0 "Laptop LCD" Absolute 0 0
   # To move windows across screen we need Xinerama and will have to force
   # the screen reolution if we want more than 1024x768 (XGA)
      Option  "Xinerama"      "true"
      Screen          1 "External UXGA" RightOf "Laptop LCD"
      Screen          1 "External Screen" Absolute 1024 0
       InputDevice     "Generic Keyboard"
       InputDevice     "Configured Mouse"
   EndSection

This may be a better config if you always use the same external screen, but less satisfactory if you need to connect to a variety of external screens.

Intel 945GM with the xorg Intel driver

This driver is used by Ubuntu 7.10 and later. With X version 7.3 and xrandr version 1.2 the configuration of X for more than one screen is simplified. This section only covers Ubuntu 7.10 and the R60e for other hardware and distributions see Xorg RandR 1.2

X RandR is used to set the size, orientation and reflection of the screen display outputs.

xrandr is the command line interface to the RandR X extension. As usual with X good documentation is hard to find, start with:

then look at:

  • $ xrandr --help
  • $ man xrandr
  • $ man intel


If upgrading from earlier versions your old xorg.conf file may contain much that is now obsolete, so in what follows I will assume that you are starting with a fresh version of /etc/X11/xorg.conf which can be generated by

   # sudo dpkg-reconfigure -phigh xserver-xorg

and then restarting X. With Gutsy (Ubuntu 7.10) using the graphical configuration (displyconfig-gtk) is likely to damage your xorg.config resulting in a 800x600 default display on reboot. In which case the above option will be useful.

The resulting /etc/X11/xorg.conf should include something like

   Section "Device"
       Identifier	"Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
       Driver		"intel"
       BusID		"PCI:0:2:0"
       # ADD THIS IF YOUR LAPTOP DOES NOT HAVE A TV CONNECTOR or DOCKING STATION 
       Option          "monitor-TV"   "TV" 
   EndSection
   Section "Monitor"
       Identifier	"Generic Monitor"
       Option		"DPMS"
   EndSection
   # ADD THIS IF YOUR LAPTOP DOES NOT HAVE A TV CONNECTOR or DOCKING STATION 
  Section "Monitor" 
       Identifier      "TV" 
       Option          "Ignore" "True" 
  EndSection 
   Section "Screen"
       Identifier	"Default Screen"
       Device		"Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller"
       Monitor		"Generic Monitor"
       DefaultDepth	24
       SubSection "Display"
           Depth		24
           # ADD A VIRTUAL LINE TO PROVIDE FOR THE LARGEST SCREENS YOU WILL HOTPLUG
           Virtual              2048 2048 
       EndSubSection
   EndSection
   Section "ServerLayout"
       Identifier	"Default Layout"
       Screen		"Default Screen"
       InputDevice	"Generic Keyboard"
       InputDevice	"Configured Mouse"
       InputDevice     "stylus"	"SendCoreEvents"
       InputDevice     "cursor"	"SendCoreEvents"
       InputDevice     "eraser"	"SendCoreEvents"
       InputDevice	"Synaptics Touchpad"
   EndSection

The example above contains some modifications:

  • The Virtual line. It is a limitation of the Intel driver that frame buffer size cannot be changed once X has started. Therefore in order to hotplug a variety of screens this should be set the allow for the largest combination of display resolutions you plan to use. For the Intel 945 chip in the R60e a virtual size larger than 2048 will disable DRI. (If you do not need 3D graphics that is not important.) By default the Virtual size is set to that of the largest display that is connected when X starts. (Note this means that if an external VGA is connected but not switched on it will still influence the virtual display size.)

xrandr is a Xinerama mode, the mouse and application windows move about the entire virtual screen, the physical monitors provide a display port view of a portion of that space. So if you want the laptop LCD and an external monitor to show different information the virtual size must be larger than the default.

monitor windows must fit within the virtual screen

  • The Monitor and Device sections for Monitor-TV. The R60e does not have a TV out socket though the graphics chip provides this capability. Disabling the TV will prevent the screen of the external monitor blanking for a few seconds whenever the xrandr program is used. (Later versions of the Intel driver may have a fix for this problem.)
  • The new minimalist xorg.conf should not need modelines, nor should it include HorizSync and VertRefresh in the Monitor section. For some screens (eg Dell 2001FP) it appears that xrandr will not provide the maximum display resolution when these options are present.

Using xrandr with Ubuntu 7.10

There is a Graphical Configuration Tool, (displayconfig-gtk) included with Ubuntu 7.10. At present it dosn't work too well.It is found in the menu: 'System: Administration: Screens and Graphics'. As using it will wreck your xorg.conf (see above) I recommend removing it.

The command line xrandr however does work quite well. Note that Gnome places the menu bar on screen 0 and that limitations of the Intel chip and driver mean this Screen 0 (the external VGA monitor) will always be the default display if it is connected. This applies even if the external monitor is switched off but the cable connected: if you have a blank laptop monitor check if you have anything plugged in to the VGA port.

So, if you start X with an external monitor connected that will be the only display until you use xrandr to change things.

Open a terminal window to use the command line: 'Applications:Accessories:Terminal'

First look at the 'help' and 'man' pages. $ xrandr --help $ man xrandr

To query what we have (nothing connected to VGA)

$  xrandr -v
   Server reports RandR version 1.2
$  xrandr -q 
Screen 0: minimum 320 x 200, current 1024 x 768, maximum 1920 x 1440
VGA disconnected (normal left inverted right)
 LVDS connected 1024x768+0+0 (normal left inverted right) 304mm x 228mm
   1024x768       60.0*+   50.0  
   800x600        60.3  
   640x480        60.0     59.9  
TV disconnected (normal left inverted right)

If you see the 'TV disconnected' line but have neither TV connector nor docking station (eg Thinkpad R60e) then add to the Monitor and Device sections of xorg.conf as noted above. This will prevent the external (VGA) flashing off for a few seconds every time xrandr is used. (Newer versions of the intel driver may fix this.)

Example with the external monitor connected, powered on and a Virtual 2624x2048. (For some reason my monitor defaults to 1280x800 for its initial display so two further xrandr commands are reguired to set up.)

$  xrandr -q 
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 2624 x 2048
VGA connected 1280x800+0+0 (normal left inverted right) 367mm x 275mm
   1600x1200      60.0 +   59.9  
   1280x1024      75.0     59.9  
   1152x864       74.8  
   1024x768       75.1     60.0  
   800x600        75.0     60.3  
   640x480        75.0     60.0  
   720x400        70.1  
LVDS connected (normal left inverted right)
   1024x768       60.0 +   50.0  
   800x600        60.3  
   640x480        60.0     59.9  
  1280x800 (0x46)   83.5MHz
        h: width  1280 start 1344 end 1480 total 1680 skew    0 clock   49.7KHz
        v: height  800 start  801 end  804 total  828           clock   60.0Hz
$ xrandr  --output LVDS --auto 
$ xrandr  --output VGA --mode 1600x1200 --pos 1024x0 

More information for bug reports

$  xrandr --verbose
$  xrandr --output LVDS --auto

gets two screens but both at 1600x1200 cloned

$  xrandr --output LVDS --mode 1024x768 --output VGA --off 

gets laptop only at 1024x768

Without a virtual set in xorg.conf

$  xrandr --output VGA --right-of LVDS --mode 1600x1200 
   xrandr: screen cannot be larger than 1600x1600 (desired size 2624x1200)
$  xrandr --output VGA  --mode 1600x1200 --pos 0x400 

creates two screens with the laptop screen at bottom of the 1600x1600 window

$  xrandr --output LVDS --mode 1024x768 --pos 0x400 

moves laptop screen to top of window, so both share same top line

$  xrandr  --output VGA --mode 1600x1200 --pos 0x768
  xrandr: screen cannot be larger than 1600x1600 (desired size 1600x1968)

edit xorg.conf and ensure we have Virtual 2048 2048. Try again and it works: we have a laptop screen in a virtual position at the top of a 2048x2048 frame with the VGA monitor below.

Next edit xorg.conf and set Virtual 2624 2048 then:

$  xrandr  --output VGA --mode 1600x1200 --pos 1024x0

Now it is possible to have the two windows side by side.

see also Sample Fn-F7 script to use xrandr with function key F7

Screen Brightness control

In 7.04 there is a problem with the Fn+home Fn+End screen brightness controls Bug 87028.

The workaround is to disable video.o

echo blacklist video | sudo tee -a /etc/modprobe.d/local

Unfortunately this only fixes the blanking screen, using the Fn+Home and Fn+End provides values of bright and dim but no intermediate values Bug 61184. A fix has been posted. First check what you have

 # lshal|grep smbios.system
 smbios.system.version = 'ThinkPad R60e'  (string)
 smbios.system.product = '06574TG'  (string)
 smbios.system.manufacturer = 'LENOVO'  (string)

then edit /usr/share/hal/fdi/policy/10osvendor/10-laptop-panel-mgmt-policy.fdi

# sudo nano -w  /usr/share/hal/fdi/policy/10osvendor/10-laptop-panel-mgmt-policy.fdi

The original release 7.04 had a <device> block for LENOVO that tested the version string for X, T, and Z model ThinkPads but not R. A subsequent update to hal has modified the file to <deviceinfo version="0.2"> and removed the Lenovo specific code. Add to the file

 <device>
   <match key="info.category" string="laptop_panel">
     <match key="/org/freedesktop/Hal/devices/computer:smbios.system.manufacturer" string="LENOVO">
       <match key="/org/freedesktop/Hal/devices/computer:smbios.system.version" contains="ThinkPad R">
         <merge key="laptop_panel.brightness_in_hardware" type="bool">true</merge>
       </match>
     </match>
   </match>
 </device>

save the file then

# sudo /etc/dbus-1/event.d/20hal restart 

and restart X (Ctrl+Alt+Backspace) Note: the onscreen bar display will not display the changed level.

Sound

There is an option in the BIOS setup to disable the modem which seems a good idea if the modem is not needed. Do not do this, if the modem is disabled then sound will not work with Ubuntu (6.06 and Edgy knot2). (Sound does however work in WinXP with the modem disabled)

Mouse and TrackPoint

see How to configure the TrackPoint Note however that to modify sensitivity and scroll rate on R60e with Ubuntu 6.06 the commands are:

    # echo -n 96 > /sys/devices/platform/i8042/serio0/speed
    # echo -n 200 > /sys/devices/platform/i8042/serio0/sensitivity

and with Ubuntu 7.10 (Gutsy)

    # echo -n 96 > /sys/devices/platform/i8042/serio1/speed
    # echo -n 200 > /sys/devices/platform/i8042/serio1/sensitivity

This needs to be typed in a root window; using sudo gives a permission denied.

Wireless

You need to install linux-restricted-modules-generic, which contains the kernel module ath_pci. ath_pci is loaded automatically at system startup.

Feisty (7.04) includes network-manager, although useful for roaming it dosn't work well for networks which do not broadcast ESSID.

Suspend-to-RAM

There seems to be a bug in edgy in relation to cpufreq governors. See Bug 70602 for details and a workaround.

Had to add following script to let the laptop go into supsend after the lid was closed:

 #!/bin/sh
 #/etc/acpi/local/lid.sh.post
 grep -q closed /proc/acpi/button/lid/*/state
 if [ $? = 0 ] ; then
   /etc/acpi/sleep.sh
 fi

7.04 (Feisty)

Both Sleep (fn+4) and Hibernate (fn+12) appear to work.

Modem

If not used: see above re sound

If used: install mwave then it should work.

to be continued

Bluetooth [setup appears ok, untested due to lack of bluetooth device]

FnF2 lock Screen working

FnF3 Display Battery Condition

FnF4 Sleep can be configured in Gnome power save option, but seems to disable fn+F12 hibernate; 'blank screen' sets screensaver (6.04 Dapper). Works without additional configuration (7.04 Feisty).

FnF5 toggle Wireless/Bluetooth on/off

FnF7 Switch Screen (HKEY 00000080 00001007) see Sample_Fn-F7_script

FnF8 TrackPoint? No Effect (ibm/hotkey HKEY 00000080 00001008)

FnF9 (ibm/hotkey HKEY 00000080 00001009) (Easy Eject in WinXP)

FnF12 Suspend to disk, seems to work, but not entirely reliable, some scrambling of text console display during restart Sometimes restart hangs after reading disk, need to deactivate/reactivate wireless. (6.06 Dapper). Does not appear to work (7.04 Feisty).

FnHome screen brighter (ibm/hotkey HKEY 00000080 00001010) (see notes above to fix regressions since 6.06 Dapper)

FnEnd screen dims (no ibm/hotkey shown with $ acpi_listen)

FnPgUp ThinkLight on/off

External Sources